Pioneer DEH-MG2037ZF Service Manual page 66

1
- Electrical and servo errors
A
Mode Digit Code
Electrical error 1,2
1,2
3,4
Servo error 1,2
1,2
1,2
1,2
1,2
1,2
B
1,2
1,2
3
4
- Mechanical errors
Mode Digit Code
Waiting for disc pulled out 1,2
1,2
C
1,2
1,2
1,2
1,2
1,2
3
4
CAM Err 1,2
1,2
1,2
1,2
D
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2
E
1,2
1,2
1,2
1,2
1,2
1,2
3
4
CAMRST Err 1,2
1,2
1,2
F
1,2
66
1
2
Name
0xA0 VD power NG
Mech Vref NG
0xA1
0x10 Setup carriage home NG
Setup focus NG
0x11
0x12 Setup spindle Lock NG /RF NG
Setup AGC NG
0x17
0x22 Setup Impossible to play (ROM)
0x23 Setup file format NG
0x30 SRH time-out during SRH
(including TRD L.I search time-out)
0x44
Setup Impossible to play (CD-DA)
Name
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x51 MFWDTO
MREVTO
0x52
MFWDTO
0x5a
0x5b MREVTO
MFWD2TO
0x5e
0x61 MFWDTO
MREVTO
0x62
MLSWNG
0x64
0x66 MREV2TO
MFWDTO
0x6a
0x6b MREVTO
MFWDTO
0x71
0x72 MREVTO
MFWDTO
0x7a
MREVTO
0x7b
0x7d MLSWNG
MREV2TO
0x7f
0x81 MFWDTO
MREVTO
0x82
MFWDTO
0x8a
0x8b MREVTO
MOVERCNT
0xaa
MFWDTO
0x91
0x92 MREVTO
MOVERCNT
0x93
0x94 MSPDERR
DEH-MG2037ZF/XU/UC
2
3
Descriptions
VD power abnormal
Mech elevation reference voltage abnormal
At the occurrence of error, motor control output (*6)
The CRG cannot move to inner tracks or move from inner tracks.
No focus
No spindle lock. Sub codes cannot be read.
AGC protection does not function. Focus is easily unlocked.
No playable MP3 file or WMA file. =No MP3 file or WMA file in the set CD-ROM
Being written in non-corresponding File Format
Cannot reach the target address.
No playable TRK No.
=
ALL of the TRK No. in the set disc has been specified with track skip information.
At the occurrence of error, claw switch value
The rotation rate does not satisfy the spec.
Descriptions
CAMRST Forced ejection Waiting for disc pulled out
WTLOAD Forced ejection Waiting for disc pulled out
EJCTON Forced ejection Waiting for disc pulled out
SEJPCK Forced ejection Waiting for disc pulled out
HLFLOAD Forced ejection Waiting for disc pulled out
DINSRDY Forced ejection Waiting for disc pulled out
LIFTDN LIFTUP Forced ejection Waiting for disc pulled out
The m2stat value at the original error followed by forced ejection (*3)
The LOAD SW value (3 bits) at the forced ejection end:
CAM motor FWD time-out error during TRAY UP operation
CAM motor REV time-out error during TRAY UP operation
CAM motor FWD time-out error during TRAY DN operation
CAM motor REV time-out error during TRAY DN operation
CAM motor FWD2 time-out error during TRAY DN operation
CAM motor FWD time-out error during CRG OUT operation
CAM motor REV time-out error during CRG OUT operation
LOAD SW ON stuck error during CRG OUT operation
CAM motor REV2 time-out error during CRG OUT operation
CAM motor FWD time-out error during CRG IN operation
CAM motor REV time-out error during CRG IN operation
CAM motor FWD time-out error during ELV IN operation
CAM motor REV time-out error during ELV IN operation
CAM motor FWD time-out error during ELV OUT operation
CAM motor REV time-out error during ELV OUT operation
LOAD SW ON stuck error during ELV OUT operation
CAM motor REV2 time-out error during ELV OUT operation
CAM motor FWD time-out error during EIN_EXP operation
CAM motor REV time-out error during EIN_EXP operation
CAM motor FWD time-out error during CIN_EXP operation
CAM motor REV time-out error during CIN_EXP operation
CAM SW has not been determined during CAM operation (Chatter remains.)
The OK stop position at the last elevation operation (*4)
The CAM SW value (3 bits) before retry (with the first error)
ELV motor FWD time-out error during CAMRST operation
ELV motor REV time-out error during CAMRST operation
Over-count error during CAMRST operation
The claws do not close during CAMRST operation.
3
4
4