Sanyo PLC-XD2200 Service Manual page 50

Electrical Adjustments
Group/
Item Name
Item
4 Cr Imange Area Start X
5 Cr Imange Area Start Y
6 Image Area H Width
7 Image Area V Hight
8 Y Target Level
9 Cb Target Level
10 Cr Target Level
11 Gain Tolerance
12 Delta Gain
Group
Auto calibration (Ycbcr)
264
0 Y-OFFSET AREA H START
1 Y-OFFSET AREA V START
2 CB - OFFSET AREA H
START
 CB - OFFSET AREA V START CB - Offset Acquiring Area V-Start
CR - OFFSET AREA H
4
START
5 CR - OFFSET AREA V START
6 Y - GAIN AREA H START
7 Y - GAIN AREA V START
8 CB - GAIN AREA H START
9 CB - GAIN AREA V START
10 CR - GAIN AREA H START
11 CR - GAIN AREA V START
12 Image AREA H WIDTH
1 Image AREA V HIGHT
14 Y - OFFSET TARTGET
15 CB OFFSET TARGET
16 CR OFFSET TARGET
17 Y-GAIN TARGET
18 CB-GAINTARGET
19 CR-GAINTARGET
20 OFFSET torelance
21 GAIN torelance
Group
cuStoM(Aspect)
270
0 Scaler Horizontal
1 Sclaler Vertical
2 Connect
 Position Horizontal
4 Position Vertical
5 Aspect Enable
Group
AutoPc Adjust
280
0 AutoPCAdjustEnable
1 Frequency Step
2 Frequency Threshold
 Fine Phase
4 BLKDET
5 PHASEMSK
Group
Paneltype * Panel type check
290
0 GammaL/R-View
1 GammaL/R-Change
Group
composite (NtSc) composite / S-Video
500
0
Function
Cr Acquiring Area H-Start Position
Cr Acquiring Area V-Start Position
Image Level Acquiring Area
Image Level Acquiring Area Height
Target Value of Y Level Adj.
Target Value of Cb Level Adj.
Target Value of Cr Level Adj.
Torelance of Level Adj.
Deviation Width of Gain Value
Y - Offset Acquiring Area H-Start
Position
Y - Offset Acquiring Area V-Start
Position
CB - Offset Acquiring Area H-Start
Position
Position
CR - Offset Acquiring Area H-Start
Position
CR - Offset Acquiring Area V-Start
Position
YCBCR Level Acquiring Area
YCBCR Level Acquiring Area Height
Torelance of OFFSET Adj.
Torelance of GAIN Adj.
Horizontal Scaler Edit
Vertical Scaler Edit
Seperate/Connect Edit
Horizontal Postion Correction
Vertical Position Correct
Aspect Adj. Enable
Auto-PC Adj Operation Enable if Un-
supported Signal Input
Frequency Steps of Total Dot
Total Dot Freqency Threshold
Do Phase Adj after Total Dot Adj.
Black Level Detection Area
Phase Detection Filter
Current Setting Check
Setting of Gamma
Initial
500
200
8
9
217
212
212
1
9
925
500
925
500
925
500
50
500
800
500
700
500
1
9
4
128
128
217
27
27
1
1
100
100
0
100
100
0
0
1
5
1
1
0
0
10
-50-
range Note
0-1000
0-1000
0-4095
0-4095
0-255
0-255
0-255
0-255
0-255
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 255
0 - 255
0-255
0-255
0-255
0-255
1-255
1-255
68-12
68-12
0-1 0:Seperate, 1: Connect
85-115
85-115
0-1 1: Enable, 0: Disable
0-1 0:Enabel, 1:Disable
0-
0-10 0[]<-- - --> 10[Not matched]
0-1 0;Excutes Fine Phase; 1:Not Excute
0 - 
0: Effective All Bit,
1: Disable Lower 1 bit
0 - 
2: Disable Lower 2 bit, : Disable
Lower  bit
0: Gamma for L-Turn
0-20
20: Gamma for R-Turn * Read only
Sets L-Turn Gamma if the Value is
set to 0.
0-20
Sets R-Turn Gamma if the Value is
set to 20.