Related Manuals for Kenwood DPF-1030
Summary of Contents for Kenwood DPF-1030
- Page 1 CD PLAYER DPF-1030 DPF-2030 INSTRUCTION MANUAL KENWOOD CORPORATION B60-4517-08 (EN)
-
Page 2: Introduction
Introduction Before applying power Units are designed for operation as follows. Australia ... AC 240 V only Europe and U.K..AC 230 V only *AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. -
Page 3: Table Of Contents
¶ Edit function for rearranging tracks according to the tape length so that no music is interrupted in the middle. ¶ Auto space function. ¶ Easy operation functions allow systematic operation with other KENWOOD components connected through the system control connection. System control cord ... (1) Batteries (R6/AA) ... -
Page 4: Important Safeguards
IMPORTANT SAFEGUARDS Please read all of the safety and operating instructions before operating this appliance. Adhere to all warnings on the appliance and in the instruction manual. Follow all the safety and operating instructions. These safety and operating instructions should be retained for future reference. -
Page 6: System Connections
“In case of difficulty”. Back panel : 10 cm Connection to KENWOOD CD TEXT MD recorder; DIGITAL OUTPUT jack The text (track titles) and the music of a CD can be copied to an MD. -
Page 7: To Use The Headphone
REMOTE CONTROL UNIT RC-P0715 To use the headphone (only for DPF-2030) Connect a stereo headphone to the PHONES jack of the CD player. Adjust the sound volume using the remote control unit. ÷ It is not favorable for the sound quality to decrease the output level from this unit too much. - Page 8 2. Do not connect system control cords to any components other than those specified by Kenwood. It may cause a malfunction and damage your equipment. 3. Be sure the system control plugs are inserted all the way in to the system control terminals.
-
Page 9: Maintenance
Maintenance Disc handling precautions Handling Hold the discs so that you do not touch the playing surface. Label side Playing side Sticker Do not attach paper or tape to either the play- ing side or the label side of the discs. Sticky paste Cleaning If fingerprints or foreign matter become at-... -
Page 10: Controls And Indicators
Controls and indicators TRACK TRACK mode indicator Program mode indicator Pause indicator Play indicator The figure shows an example for the DPF-2030 2 3 4 POWER - ON – OFF P.MODE PHONES EDIT 0 ! @ The keys with the same name as those on the remote control unit operate the same way as the remote control unit. -
Page 11: Operation Of Remote Control Unit
Operation of remote control unit TIME DISP P.MODE EDIT CLEAR CHECK RANDOM REPEAT ¡ ¢ DOWN OUTPUT LEVEL REMOTE CONTROL UNIT RC-P0715 Loading batteries 1 Remove the cover. Operation After plugging in the power cord, press the POWER switch of the main unit to turn the unit ON. When the unit is turned ON, press the key of the function to be operated. -
Page 12: Normal Play (Track Mode)
Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. Playing tracks in order from track No. 1 Press the POWER switch to ON. Load a disc. Open the tray. Place a disc. -
Page 13: Playback From Desired Track
Playback from desired track (except for DPF-1030) REMOTE CONTROL UNIT RC-P0715 Skipping tracks To skip backward Searching Backward search Time display on CD player (TIME DISPLAY) Each press of the TIME DISPLAY key changes the displayed contents. TIME DISPLAY Press the numeric keys as shown below... -
Page 14: Programmed Play (Pgm Mode)
Do this operation in the stop mode. Go to step 2 within 5 seconds. Program desired tracks. Select the desired track No. Remote control unit Main unit (Except for DPF-1030) (Except for DPF-2030) Press the numeric keys as (Programming is not shown below... possible during playback) To enter track No. -
Page 15: To Check Or Change The Programmed Tracks
Press until the track No. to CHECK be changed is displayed. Select the new track No. Remote control unit Main unit (Except for DPF-1030) (Except for DPF-2030) ¢ Set the entry. P.MODE To add a track to the program Do this operation in stop mode. -
Page 16: Repeated Playback
Do this operation in the stop mode. Press so that the "PGM" indicator lights. Select the desired track No. Remote control unit Main unit (Except for DPF-1030) (Except for DPF-2030) Press the numeric keys as shown below... To enter track No. 15: 05 ¢... -
Page 17: To Repeat The Entire Disc
To repeat the entire disc Press so that the “TRACK” indicator lights. If the "PGM" indicator is lit, press the P.MODE key. P.MODE Switch REPEAT ON. REPEAT Start playback. To cancel repeated playback Press the REPEAT key again. REPEAT : Keys and control used in the operations described on this page. Lights up. -
Page 18: Editing
6 key again to continue playback. When recording the edited content onto a tape, it is recommended to use the synchro recording or CCRS recording function of KENWOOD cassette decks. ÷ Do not adjust the output level from this unit particularly during record- ing. -
Page 19: To Check The Edited Contents
To check the edited contents CHECK To clear the edited contents Press any one of these keys. P.MODE OPEN/CLOSE Peak search This function identifies the highest peak level of the entire recording on a CD before recording the CD on the cassette deck. With this unit, after the peak level of each track recorded on the CD has been searched, the section of the music containing the highest peak level will be played repeatedly so that the recording level of the cassette deck or MD (analog recording) can be adjusted easily. -
Page 20: Playback In Random Order (Random Playback)
Playback in a random order (Random playback) As tracks are selected at random, you can enjoy listening to for a long time. Preparation ÷ Load a disc in the CD player. ™ Press the P.MODE key so that the "TRACK" indicator lights. -
Page 21: Timer Operations
Turn OFF the power output from the audio timer. 1. Some amplifiers cannot be used with a timer. Before using a amplifier, check it. 2. When operating the unit other than CD player using an audio timer, be sure to remove the disc from the CD player. Notes... -
Page 22: In Case Of Difficulty
Set the unit to POWER OFF by pressing the POWER key, and after a few seconds, turn the unit POWER ON by pressing the POWER key again. ÷ Please be aware that resetting the CD player will erase all stored information and return it to the factory settings. Cause ÷... -
Page 23: Specifications
Weight (Net) ... 4.3 kg (9.5 lb) 1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature). - Page 24 For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product.