Related Manuals for Team Losi Speed T
Summary of Contents for Team Losi Speed T
- Page 1 ® ® Not responsible for errors. All prices subject to change without notice. Losi, a Division of Horizon Hobby, Inc.
-
Page 2: Table Of Contents
® ® Table of Contents Introduction Safety Precautions: Caution: THIS PRODUCT IS NOT A TOY. This product is not intended for Introduction ....................2 Thank you for purchasing the Losi ™ Speed-T RC vehicle We hope you operate this RC model in a safe, reasonable use by children without direct adult supervision. -
Page 3: Supplied And Required Equipment
® ® Batteries and Charging: Supplied and Required Equipment Required Equipment: If you are going to be using a charger other than a peak detection charger it is important to have your battery fully The Speed-T uses rechargeable batteries such as NiMH or Four (4) AA alkaline batteries for the transmitter. Supplied tools: discharged prior to recharging. Many of these have a 15-20 LiPo. - Page 4 ® ® The Losi Speed-T Overview The Losi MTX Pro Radio System Overview Wheelie Xcelorin Brushless Antenna Motor Gear/Slipper Cover Rear Rear Camber Dual Rate Steering Wheel Suspension Adjustment (ST. D/R) Link Steering Trim (ST. Trim) Throttle Trim Power On/Off (TH.
-
Page 5: Battery Overview/Requirements
® ® Speed-T Electronics System Overview Battery Overview/Requirements The Speed-T is equipped with the Xcelorin Brushless System combined with the Losi EC3 connector. It has been designed to provide the maximum current flow to the Xcelorin Brushless System. Losi EC3 Connector Xcelorin 4800Kv Motor MRX3000 Receiver LOSB9616 Losi EC3 Connector Set, Male/Female Pair (shown here) LOSB9615 Losi EC3 Battery Connector Set, Female (2) Power Capacitor LOSB9614 Losi EC3 Battery Connector Set, Male (2) Bind Plug Xcelorin ESC It is recommended that you use the Losi EC3 connectors on all your battery packs to ensure efficient power delivery to the Xcelorin On/ Off Switch Brushless System. The connector is gold plated and is able to handle the high current loads of the Speed-T. Setup/Program Button Digital Servo Overview of Battery Packs for Use... - Page 6 ® ® Losi ONLY reccomends the following battery packs be used Related accessories (not included) that maybe helpful in the Installing Batteries: in the Speed-T. operation of your Speed-T. Transmitter Below are four (4) types of configurations that will fit nicely in your Speed-T. Remove the battery cover from the bottom of the transmitter by sliding it away from the base of the handle. Install the four (4) AA size batteries (not included) into the base, noting polarity when inserting each battery. 6-cell side-by-side configuration LOSB9616 Losi EC3 Connector Set, Male/Female Pair (shown here) LOSB9615 Losi EC3 Battery Connector Set, Female (2)
-
Page 7: Quick Start
® ® Battery Pack(s) Quick Start To install the battery pack remove the battery hold-down strap by removing the clip from the front mounting boss, and then, while Note: Please read the entire manual to gain a full understanding of the Speed-T vehicle, lifting the strap, pulling forward in one motion. -
Page 8: Losi Mtx Pro Radio System
® ® Losi MTX Pro Radio System Using the End Point Antenna Adjustments: All the adjust pots increase throw if turned clockwise and decrease throw turned counter-clockwise. The Losi MTX Pro DSM ® radio system included with the Speed-T operates on 2.4GHz and provides 79 unique channels, which are Steering: First set the steering trim so the Speed-T goes straight without touching the steering wheel. Lift the vehicle off the ground automatically selected when the transmitter and vehicle are turned on. -
Page 9: Xcelorin Brushless Electronic Speed Control
® ® Re-Bind Process Xcelorin Brushless Electronic Speed Control Ensure that the transmitter and vehicle are both turned off. Overview Using the supplied Bind plug (which looks like a standard receiver plug with a short wire loop installed), insert the Bind plug into the receiver slot labeled “BIND. ” When you look down on the receiver slots it is the slot furthest from the LED, and nearest The Losi Xcelorin electronic speed control (ESC) is specifically designed for operating Sensorless brushless motors. Featuring low to the corner of the receiver. - Page 10 ® ® Profile Overview Selecting profiles: When you are finished, press and hold the setup Using the Quick Programming Card button 2 seconds, the 4 status LEDs will scroll With the QPC in your hand and the back facing you, notice the Notice that Profile #3 is set from Profile #1 - “High Speed Performance” and the new selection will be stored to the active small jumper connectors.
-
Page 11: Driving The Speed-T
® ® Driving the Speed-T ESC Warning LEDs: Confirmation of Full Throttle and Brake: • If the Battery low voltage cutoff (LVC) is reached the • While the ESC is on and operational if you pull the throttle How you drive your Speed-T will also affect your run times. If Red LED will blink. Please note the following precautions before running trigger to Full Throttle the Green LED will turn ON Solid. -
Page 12: Tuning, Adjusting And Maintaining The Speed-T
® ® Tuning, Adjusting and Maintaining the Speed-T Periodically examine your Speed-T for the following: Tuning the Front End of the Speed-T Inboard Camber Location: The Speed-T has three different Outboard Camber Location: In addition to the inboard • Keep your vehicle clean using a brush to remove dirt inner locations with vertical adjustment for the front camber camber location, the Speed-T also provides outboard three Shock Location: The Speed-T has two mounting locations... - Page 13 ® ® Tuning the Rear End of the Speed-T Tuning the Chassis of the Speed-T Battery Position: This is a critical adjustment that is often Locker Differential (Spool) overlooked but can be very useful. Start by running the battery (Standard equipment for Speed-T) Slipper Adjustment: This should be done after the locker-diff Shock Location: Moving the shocks out on the arm will result spaced in the middle (standard setup with 6-cell battery pack).
-
Page 14: Troubleshooting Your Speed-T
® ® Troubleshooting your Speed-T Standard Ball Differential Adjustment: Adjusting Gear Mesh Off-Road Gearing (optional, not included) Incorrect gear mesh is the most common cause of stripped spur See Note 1 Many questions are the result of simple user errors or minor Never allow the diff to slip; that’s what the slipper is for. Before gears. To set the gear mesh, one method is to cut a narrow strip adjustments which are easily addressed. -
Page 15: Warranty Information
® ® Warranty Information Vehicle runs slow/slow acceleration: If you as the Purchaser or user are not prepared to accept Non-Warranty Repairs the liability associated with the use of this Product, you are Check the battery connectors. Should your repair not be covered by warranty the repair Age Recommendation: Ages 14 and up. -
Page 16: Rc Terminology
® ® Warranty Information (cont.) RC Terminology Compliance Information for the European Union BEC (Battery Elimination Circuit) – The BEC is used to eliminate GUID – Globally Unique Identification Code. Each Sensorless – Is a type of brushless system, of which there are the need for a receiver pack to power the radio system. - Page 17 ® ® Replacement Parts List Part Number Description Price Part Number Description Price LOSA4136 Front and Rear Inner Pin Brace Set (XXX, XXX-T) ................$3.00 LOSA1022 Front Axles for XX-T Wheels (GTX, NXT, XXX-T) ..................$6.00 LOSA4170 Battery Strap, Pad, and Foam Block (XXX-TCR-Speed-T) ..............$4.49 LOSA1113 Front Shock Tower (Speed-T) ........................$5.99 LOSA4224 Threaded Chassis Inserts - Short and Long ..................$6.50 LOSA1118 Front Suspension Arms (Speed-T) ......................$7.99 LOSA5013 Front and Rear Upper Shock Mount Bushings (XXX,T) ..............$3.00 LOSA1146 Front Outer & Kingpins 3/32” (XX, ‘CR’ , XXX, XXX-T) .................$3.00 LOSA5015 Double O-Ring Shock Cartridge ......................$2.00 LOSA1150...
- Page 18 ® ® Optional Parts for the Speed-T Part Number Description Price LOSA2961 CVD Rebuild Kit: Speed-T ...........................$5.99 LOSA3009 Differential Balls 3/32” (12) (Optional) ....................$1.25 LOSA3065 Silicone Differential Compound (Optional) ..................$2.50 LOSA3927 90-Tooth, 48-Pitch Spur Gear for Double-Disk Slipper ..............$3.50 LOSA3929 86-Tooth, 48-Pitch Spur Gear for Double-Disk Slipper ..............$3.50 LOSA3930 84-Tooth, 48-Pitch Spur Gear for Double-Disk Slipper ..............$3.50 LOSA3932 78-Tooth, 48-Pitch Spur Gear for Double-Disk Slipper ..............$3.50 LOSA3933 76-Tooth, 48-Pitch Spur Gear for Double-Disk Slipper ..............$3.50 LOSA4112 48 Pitch Pinion Gear,12T ..........................$4.00 LOSA4113 48 Pitch Pinion Gear,13T ..........................$4.00 LOSA4114 48 Pitch Pinion Gear,14T ..........................$4.00 LOSA4115...
- Page 19 ® ® LOSA6206 LOSA5051 LOSA4122 LOSA1620 LOSA1610 LOSA5158 LOSA1113 LOSA1620 LOSA5051 LOSA1610 LOSA5013 LOSA3034 LOSA1615 LOSA1620 LOSA6300 LOSA6350 LOSA6305 LOSA6306 LOSA6215 LOSA2105 LOSA4133 LOSA5160 LOSA4133 LOSA5073 LOSA1620 LOSA6216 LOSA6204 LOSA6305 LOSA1620 LOSA6100 LOSA6001 LOSA6300 LOSA6229 LOSA6229 LOSA5073 LOSA6350 LOSA5017 LOSA6100 LOSA5045 LOSA4170 LOSA4231...
- Page 20 ® ® Use this page to record tuning information Use this page to record tuning information...
- Page 21 ® ® ©2008 Losi, A division of Horizon Hobby, Inc. Not responsible for typographical errors. 800-0349 All pricing subject to change without notice. Revised 08/09 12660.1...