Audio Setup Memory (Pro Mode) - Kenwood KDC-PSW9527 Instruction Manual

2nd section
Multi-function key operation
[2] [2] "USER"
"MEMORY" [3] "INST"
[3] [2] "USER"
"CALL" [3] "INST"
• You can store an adjusted audio setup value by
" "
selecting MEMORY . Also, you can recall it by
" ".
selecting CALL Refer to 'Audio Setup memory Recall'
(page 32).
3
Adjust the Audio setup item
Press the [4] or [¢] button.
Each time the button is pressed the setting
switches as shown below.
Adjustment Item
High Pass Filter Front
High Pass Filter Rear
3
High Pass Filter Center*
Low Pass Filter Subwoofer
Subwoofer Phase setting
DTA Front/DTA Rear/
DTA Subwoofer
DTA Center* 3
Bass Center Frequency
Middle Center Frequency
Treble Center Frequency
Bass Level/ Middle Level/
Treble Level
Bass Q Factor/ Middle Q Factor/
Treble Q Factor
SP-LEV Front Left/SP-LEV Front Right
SP-LEV Rear Left/SP-LEV Rear Right
3
SP-LEV Center* /SP-LEV Subwoofer
• The Adjustment item can also be controlled by the
rotary volume knob. Refer to 'Rotary Volume knob
operation mode select' (page 13).
• To get the best sound, first set the "CABIN" and "SP-
SEL" parameters using the 'Audio Setup (Easy mode)'
(page 28). Refer to 'Notes on Sound Management
System' (page 11).
3
• * Function of the KDC-PSW9527
• When the 'Dual Zone System' (page 24) is ON, each of
the following setup is ignored.
- "X'over"/ "EQ" / "DTA"
4
Exit Audio setup mode
Press the [6] ("RTN") button.
Audio setup item
User Memory
User Insttaller
Call User
Call Insttaller
Range
Through/30 — 250 (Hz)
30 — 250 (Hz)
Normal/ Reverse
0 — 610 (cm)
0 — 170 (cm)
60 — 400 (Hz)
500 (Hz) — 3.15 (KHz)
4.00 (kHz) — 16.00 (KHz)
-9 — +9 dB
0.25/ 0.50/ 1.00/ 2.00
-10 — +10

Audio Setup Memory (PRO mode)

1
Selects the PRO mode of Audio setup
See the 'Audio Setup' (page 50) and select "Audio
Setup: PRO".
2
Select the source for adjustment
Press the [SRC] button.
3
Select the key function section
Press the [NEXT] button.
Repeatedly press the button until "AD SET" is
displayed above the [3] button.
Refer to 'Notes on Multi-function Key System'
(page 10).
4
Enter Audio Setup mode
Press the [3] ("AD SET") button.
5
Select the Adjustment item section
Press the [NEXT] button.
Repeatedly press the button until the desired
Adjustment item is displayed above the [2] — [5]
button.
6
Select the Audio Setup item for adjustment
Press the [2] — [5] button.
Adjust the audio setup by referring to the 'Audio
Setup (PRO mode)' (page 30).
7
Select the Memory item section
Press the [NEXT] button.
Repeatedly press the button until "MEMORY" is
displayed above the [2] button.
8
Select the Memory item
Press the [2] ("MEMORY") button.
9
Stores the adjusted audio setup value in
memory
Press the [2] ("USER")/ [3] ("INST") button for
at least 2 seconds.
The "MEMORY" display blinks 1 time.
"USER": The values are erased from memory if the
battery is removed or if the reset button
is pressed.
"INST": The values are held in memory even if the
battery is removed or if the reset button
is pressed.
10
Exit Audio Setup mode
Press the [6] ("RTN") button.
31
|
English