Download Print this page

Dimplex XMX706N Installation And Operating Instructions

Xms(n) automatic xmx(n) storage heater range

Advertisement

XMS(N)
STORAGE HEATER RANGE
MODELS:
INSTALLATION
PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER USE.
NOTE ALSO THE INFORMATION GIVEN ON THE HEATER
The installation must be carried out by a trained competent personnel.
A means for disconnection must be incorporated in the fi xed wiring by a double pole switch with a contact separation
of a minimum of 3mm and in accordance with the current IEE Wiring Regulations
The heater must not be installed immediately below a fi xed socket outlet.
The heater is not suitable for connection to a 30A ring circuit (24 hour peak supply).
Do not position the heater under windows where curtains can contact the heater casing.
WARNING - THE SURFACES ON THIS HEATER CAN BE HOT
This heater meets EN60335 safety requirements. However, any heater type becomes hot in normal operation. Care
must be taken to ensure that prolonged skin contact with the heater does not occur.
WHERE YOUNG CHILDREN, INFIRM PERSONS, OR THE AGED ARE PRESENT THIS APPLIANCE MUST BE
ADEQUATELY GUARDED. Contact your installer or manufacturer for further advice.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision for instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
This appliance is very heavy and must be securely fi xed to a wall. DO NOT UNDER ANY CIRCUMSTANCES
ATTEMPT TO MOVE OR REPOSITION THIS HEATER WITHOUT SEEKING EXPERT ADVICE.
To maintain stability, it is essential that the heater is placed on a level surface.
This heater must be installed where it is impossible for switches and other controls to be touched by a person using
a bath or shower.
IMPORTANT - Due to the newness of materials the heater will produce a slight smell for the fi rst few days of
operation. ROOMS MUST BE WELL VENTILATED AND YOUNG CHILDREN, CAGED BIRDS, OR PERSONS
WITH RESPIRATORY COMPLAINTS MUST NOT REMAIN IN CLOSE PROXIMITY TO THE HEATER DURING
THE FIRST 48 HOURS OF THE COMMISSIONING PERIOD.
IF, DURING ANY REASSEMBLY OF THE HEATER, A PART OF THE THERMAL INSULATION SHOWS DAMAGE
OR DETERIORATION WHICH MAY IMPAIR SAFETY, IT SHOULD BE REPLACED BY AN IDENTICAL PART.
AUTOMATIC
XMX706N - 6kWh
XMS/X718N - 18kWh
INSTRUCTIONS
IMPORTANT
XMX(N)
XMS/X712N - 12kWh
XMS/X724N - 24kWh
OPERATING
AND
MANUAL

Advertisement

loading

Summary of Contents for Dimplex XMX706N

  • Page 1 XMS(N) XMX(N) AUTOMATIC MANUAL STORAGE HEATER RANGE MODELS: XMX706N - 6kWh XMS/X712N - 12kWh XMS/X718N - 18kWh XMS/X724N - 24kWh INSTALLATION OPERATING INSTRUCTIONS IMPORTANT PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER USE. NOTE ALSO THE INFORMATION GIVEN ON THE HEATER The installation must be carried out by a trained competent personnel.
  • Page 2: Circuit Diagram

    INSTALLATION INSTRUCTIONS Place the heater on its feet and in the desired position PREPARATION against the wall. Ensure the heater is based on a fi rm level surface at least 75mm from any end wall and at least The heater will arrive Model 706N - 4 bricks 250mm below any shelf or similar projection.
  • Page 3 THE FOLLOWING MUST BE APPLIED WHEN FIXING THE HEATER TO THE WALL BRACKET i) If no skirting board is present secure the heater through the wall bracket slots closest to the wall. ii) If 100mm (4in.) skirting is present secure the heater through the outer slots.
  • Page 4: Safety Instructions

    Should you require after sales information please go to THE INPUT CONTROL www.dimplex.co.uk where you will fi nd our self help guide by clicking For models XMS712N, 718N, 724N only: on ‘After Sales’ or ring our help desk on 0845 600 5111 (UK) or 01842 4833 (ROI).

This manual is also suitable for:

Xms/x718nXms/x712nXms/x724nXms718nXmx718nXms712n ... Show all