Philips 19PFL3504D/F7 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. LCD TV
  5. 19PFL3504D/F7
  6. Service manual

Philips 19PFL3504D/F7 Service Manual

Hide thumbs Also See for 19PFL3504D/F7:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual

Service Manual

© 2009 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
19"
22"
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
chassis FL9.0
Contents
19PFL3504D/F7
22PFL3504D/F7
LCD TV
Subject to modification

Advertisement

Table of Contents
loading

Related Manuals for Philips 19PFL3504D/F7

Summary of Contents for Philips 19PFL3504D/F7

  • Page 1: Service Manual

    LCD TV chassis FL9.0 Service Manual Contents 19” 19PFL3504D/F7 22” 22PFL3504D/F7 © 2009 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai.

  • Page 2: Important Safety Notice

    IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions .

  • Page 4: Specifications

    < LCD PANEL > Description Condition Unit Nominal Limit Horizontal pixels 1366 1. Native Pixel Resolution Vertical pixels [19PFL3504D/F7] 2. Brightness (w / filter) cd/m [22PFL3504D/F7] Horizontal ° -85 to 85 3. Viewing Angle Vertical ° -80 to 80 < VIDEO >...

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 6 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
  • Page 7 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View Bottom View 1.
  • Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 11 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 13: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS [19PFL3504D/F7] 1. Disassembly Flowchart Removal Step/ This flowchart indicates the disassembly steps for the Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
  • Page 14 [2] Rear Cabinet (S-2) (S-3) (S-2) (S-2) [1] Stand Assembly (S-1) Fig. D1 A91N2DC...
  • Page 15 [15] Front Cabinet (S-13) [4] Digital Main [11] Speaker CBA Unit [3] Jack [9] LCD Module Holder(D) Assembly (S-13) Speaker Cushion (S-6) (S-4) (S-12) Speaker [10] Speaker Cushion Holder(s) (S-5) Shield Box (N-1) (S-12) [11] Speaker [5] Jack [12] Function Holder(A) (S-7) (S-10)
  • Page 16 TV Cable Wiring Diagram To LCD Module Assembly To LCD Module Assembly Digital Main Main CBA CBA Unit CN201 CN3902 CN301 CN3701 CN1001 CN302 CN3702 CN1002 Jack CBA CN702 CN872 CN102 CN701 AC CORD CN871 To Speaker Junction CBA CN101 CL102A To Speaker IR Sensor CBA...
  • Page 17 CABINET DISASSEMBLY INSTRUCTIONS [22PFL3504D/F7] 1. Disassembly Flowchart Removal Step/ This flowchart indicates the disassembly steps for the Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
  • Page 18 [2] Rear Cabinet (S-2) (S-3) (S-2) (S-2) [1] Stand Assembly (S-1) Fig. D1 A9172DC...
  • Page 19 [15] Front Cabinet (S-13) [4] Digital Main [11] Speaker CBA Unit [3] Jack [9] LCD Module Holder(D) Assembly (S-13) Speaker Cushion (S-6) (S-4) (S-12) Speaker [10] Speaker Cushion Holder(s) (S-5) Shield Box (N-1) (S-12) [11] Speaker [5] Jack [12] Function Holder(A) (S-7) [14] Junction...
  • Page 20 TV Cable Wiring Diagram To LCD Module Assembly To LCD Module Assembly Digital Main CBA Unit Main CBA CN3902 CN201 CN1550 CN3701 CN301 CN302 CN3702 CN1650 CN1750 CN702 Jack CBA AC CORD CN872 CN102 CN701 CN871 To Speaker Junction CBA CN101 CL102A To Speaker...

  • Page 21: Electrical Adjustment Instructions

    ELECTRICAL ADJUSTMENT INSTRUCTIONS How to set up the service mode: General Note: “CBA” is abbreviation for “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Use the service remote control unit. replacing circuit components and certain mechanical parts. It is important to perform 2.

  • Page 22: Vcom Adjustment

    1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, Test Point Adj. Point green, blue, and white to check for non-active pixels. [CHANNEL UP/DOWN ] 1. Enter the Service mode. Screen buttons 2. Each time pressing [7] button on the service M.

  • Page 23: White Balance Adjustment

    The white balance adjustment should be 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff performed when replacing the LCD Panel adjustment. Press [3] button to select “COB” for or Digital CBA. Blue Cutoff adjustment. [DRIVE] 3. White Balance Adjustment Press [4] button to select “DR”...

  • Page 24: How To Initialize The Lcd Tv

    HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

  • Page 25: Firmware Renewal Mode

    FIRMWARE RENEWAL MODE Equipment Required The appearance shown in *1 is described as follows. Appearance State a. USB memory Downloading the firmware from b. Remote Control Unit Downloading... the USB memory. Writing the downloaded firmware Writing... Firmware Update Procedure in flash memory. Checking...

  • Page 26: Troubleshooting

    TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (D601, D602, D603, D604, Q601, Q602, T601) Is the INV+31V line voltage normal? FLOW CHART NO.2...
  • Page 27 FLOW CHART NO.6 PANEL+24.5V is not output. FLOW CHART NO.7 PANEL+13V is not output. FLOW CHART NO.8 P-ON+7V is not output. FLOW CHART NO.9 P-ON+5V is not output. (PANEL+13V is outputted normally.) Replace Q635(Q636). A91N2TR...

  • Page 28: Flow Chart No

    FLOW CHART NO.10 TUNER+5V is not output. (PANEL+13V is outputted normally.) Replace Q637. FLOW CHART NO.11 P-ON+3V is not output. FLOW CHART NO.12 P-ON+3.3V(PANEL+3.3V) is not output. FLOW CHART NO.13 P-ON+9V is not output. (PANEL+13V is outputted normally.) Replace Q641. A91N2TR...

  • Page 29: Flow Chart No

    FLOW CHART NO.14 AL+3.3V is not output. (P-ON+7V is outputted normally) FLOW CHART NO.15 LCD-7.1V is not output. Replace Q206. FLOW CHART NO.16 SP+14V is not output. A91N2TR...

  • Page 30: Flow Chart No

    [ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Re-install the switches (SW101, SW103~SW107) correctly or replace the poor switch. Check the switches (SW101, SW103~SW107) and their periphery, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit.

  • Page 31: Flow Chart No

    FLOW CHART NO.4 Picture does not appear normally.(Tuner input) FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr A91N2TR...
  • Page 32 [ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Check JK851, SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Check the line between Pin(4, 11) of IC771 and input...
  • Page 33 FLOW CHART NO.3 Audio is not outputted normally.(Tuner input) Check TU302 and their periphery circuit, and service it if defective. Check JK851, SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.4 Audio is not outputted normally.(HDMI Audio input) Check the line between Pin(5, 14) of IC771 and input terminal(JK721, JK722), and service it if defective.
  • Page 34 FLOW CHART NO.5 Audio is not outputted normally.(PC Audio input) Check the line between Pin(1, 12) of IC771 and input terminal(JK711), and service it if defective. Check JK851, SP861,SP862 and their periphery circuit, and service it if defective. A91N2TR...

  • Page 35: Block Diagrams

    BLOCK DIAGRAMS System Control Block Diagram A91N2BLS...
  • Page 36 Video Block Diagram A91N2BLV...
  • Page 37 Audio Block Diagram A91N2BLA...
  • Page 38 Digital Signal Process Block Diagram A91N2BLD...
  • Page 39 Inverter Block Diagram [19PFL3504D/F7] A91N2BLINV...
  • Page 40 Inverter Block Diagram [22PFL3504D/F7] A9172BLINV...
  • Page 41 Power Supply Block Diagram [19PFL3504D/F7] A91N2BLP...
  • Page 42 Power Supply Block Diagram [22PFL3504D/F7] A9172BLP...

  • Page 43: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 44 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
  • Page 45 Main 1/4 Schematic Diagram [19PFL3504D/F7] 10-3 A91N2SCM1...
  • Page 46 Main 2/4 Schematic Diagram [19PFL3504D/F7] 10-4 A91N2SCM2...
  • Page 47 Main 3/4 Schematic Diagram [19PFL3504D/F7] 10-5 A91N2SCM3...
  • Page 48 Main 4/4 Schematic Diagram [19PFL3504D/F7] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
  • Page 49 Main 1/4 Schematic Diagram [22PFL3504D/F7] 10-7 A9172SCM1...
  • Page 50 Main 2/4 Schematic Diagram [22PFL3504D/F7] 10-8 A9172SCM2...
  • Page 51 Main 3/4 Schematic Diagram [22PFL3504D/F7] 10-9 A9172SCM3...
  • Page 52 Main 4/4 Schematic Diagram [22PFL3504D/F7] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
  • Page 53 Jack Schematic Diagram A91N2SCJ 10-11...
  • Page 54 Function Schematic Diagram 10-12 A91N2SCF...
  • Page 55 IR Sensor & Junction Schematic Diagram 10-13 A91N2SCIR...
  • Page 56 Digital Main 1/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into seven and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. 10-14 A91N2SCD1...
  • Page 57 Digital Main 2/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into seven and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. 10-15 A91N2SCD2...
  • Page 58 Digital Main 3/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into seven and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. 10-16 A91N2SCD3...
  • Page 59 Digital Main 4/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into seven and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. A91N2SCD4 10-17...
  • Page 60 Digital Main 5/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into seven and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. A91N2SCD5 10-18...
  • Page 61 Main CBA Top View [19PFL3504D/F7] Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used. CAUTION ! Also, in order to have the ability to increase the input Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 62 Main CBA Bottom View [19PFL3504D/F7] Because a hot chassis ground is present in the power CAUTION ! supply circuit, an isolation transformer must be used. Also, in order to have the ability to increase the input Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 63 Main CBA Top View [22PFL3504D/F7] Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used. CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input CAUTION ! : For continued protection against risk of fire, slowly,when troubleshooting this type power supply...
  • Page 64 Main CBA Bottom View [22PFL3504D/F7] Because a hot chassis ground is present in the power CAUTION ! supply circuit, an isolation transformer must be used. Also, in order to have the ability to increase the input Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, slowly,when troubleshooting this type power supply...
  • Page 65 Jack CBA Top View BA91N2F01021-A 10-23...
  • Page 66 Jack CBA Bottom View BA91N2F01021-A 10-24...
  • Page 67 IR Sensor CBA Top View Function CBA Top View IR Sensor CBA Bottom View Function CBA Bottom View BA91N2F01021-C Junction CBA Junction CBA Top View Bottom View BA91N2F01021-B BA91N2F01021 10-25...

  • Page 68: Waveforms

    WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) Pin 4 of CN302 Pin 17 of CN302 CVBS 0.2V 20µs VIDEO-Pb 0.2V 20µs Pin 8 of CN302 Pin 19 of CN302 20µs...

  • Page 69: Wiring Diagram

    WIRING DIAGRAM [19PFL3504D/F7] 12-1 A91N2WI...
  • Page 70 WIRING DIAGRAM [22PFL3504D/F7] 12-2 A9172WI...

  • Page 71: Exploded Views

    EXPLODED VIEWS Cabinet [19PFL3504D/F7] Digital Main CBA Unit SP861 CL871 CL3701 CL3902 CL201 CL3702 CL872 SP862 Junction CBA Function CBA LCD1 CL701 IR Sensor CBA Jack CBA Main CBA Stand Assembly See Electrical Parts List for parts with this mark.
  • Page 72 Cabinet [22PFL3504D/F7] Digital Main CBA Unit SP861 CL871 CL3701 CL3902 CL201 CL3702 CL872 SP862 Junction CBA Function CBA LCD1 CL701 IR Sensor CBA Jack CBA Main CBA Stand Assembly See Electrical Parts List for parts with this mark. AC601 13-2 A9172CEX...
  • Page 73 Packing X10 X11 Tape Stand Assembly Packing Tape Tape Packing Tape Packing Tape Some Ref. Numbers are not in sequence. Packing Tape 13-3 A91N2PEX...

  • Page 74: Mechanical Parts List

    MECHANICAL PARTS LIST [19PFL3504D/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. REMOTE CONTROL TRANSMITTER YKF259- URMT34JHG001 Before replacing any of these components, read BATTERY R03-B500/01S XB0M451CZB01 carefully the product safety notice in this service...
  • Page 75 Don't degrade the safety of the product CHILD SAFETY SHEET A91H2UH 1EMN24526 through improper servicing. CONNECTION GUIDE A91N2UH 1EM325917 REGISTRATION CARD(PHILIPS) A91H2UH 1EMN24599 NOTE: Parts that are not assigned part numbers WALL MOUNT INSTRUCTION A91H2UH 1EMN24527 (---------) are not available.

  • Page 76: Electrical Parts List

    ELECTRICAL PARTS LIST [19PFL3504D/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C607 POLYESTER FILM CAP . (PB FREE) 0.082µF/ CA2A823DT018 100V J Before replacing any of these components, read C608 POLYESTER FILM CAP .
  • Page 77 Ref. No. Description Part No. Ref. No. Description Part No. C1007 CAP CERAMIC (AX) 2200pF/50V/B/K CA1J222TU061 D407 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1008 CAP CERAMIC HV 10pF/6KV/SL/J CCA1000TE009 D408 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1009 ELECTROLYTIC CAP . 10µF/50V M CE1JMASDL100 D409 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1010...
  • Page 78 Ref. No. Description Part No. Ref. No. Description Part No. D1016 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1003 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1018 DIODE ZENER 10BSB-T26 NDTB010BST26 Q1004 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1020 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26 Q1005# FET MOS SMD TPC8214-H QF2ZTPC8214H D1021 DIODE ZENER 15BSB-T26 NDTB015BST26 Q1006...
  • Page 79 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 82 Ω CHIP RES. 1/10W F 3.3k Ω R305 RRXAJR5Z0820 R673 RRXAFR5H3301 CHIP RES.(1608) 1/10W 0 Ω CHIP RES. 1/10W F 10k Ω R313 RRXAZR5Z0000 R674 RRXAFR5H1002 CHIP RES.
  • Page 80 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 1.5k Ω R1025 RRXAJR5Z0152 R1108 WIRE CP STP-S-0.50 XZ40F0REN001 RES CARBON FILM T 1/4W J 2.2k Ω CHIP RES. 1/10W F 2.2k Ω R1026 RCX4222T1001 R1109 RRXAFR5H2201 CHIP RES.
  • Page 81 Ref. No. Description Part No. Ref. No. Description Part No. RES CARBON FILM T 1/4W J 56k Ω C743 CHIP CERAMIC CAP . F Z 1µF/10V CHD1AZ30F105 R763 RCX4563T1001 CHIP RES. 1/10W J 56k Ω C744 CHIP CERAMIC CAP . F Z 1µF/10V CHD1AZ30F105 R764 RRXAJR5Z0563...
  • Page 82 Ref. No. Description Part No. RES CARBON FILM T 1/4W G 2.7k Ω R112 RCX4272T1002 RES CARBON FILM T 1/4W G 4.7k Ω R113 RCX4472T1002 RES CARBON FILM T 1/4W G 8.2k Ω R114 RCX4822T1002 RES CARBON FILM T 1/4W G 18k Ω R115 RCX4183T1002 SWITCHES...
  • Page 83 ELECTRICAL PARTS LIST [22PFL3504D/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C633 CERAMIC CAP . B K 1500pF/1KV CCD3AKP0B152 Before replacing any of these components, read C636# ELECTROLYTIC CAP . 100µF/25V M CE1EMASDL101 carefully the product safety notice in this service C638...
  • Page 84 Ref. No. Description Part No. Ref. No. Description Part No. C1501 ELECTROLYTIC CAP . 470µF/35V M CE1GMZNDL471 D404 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1502# CERAMIC CAP . B K 2200pF/500V CCD2JKS0B222 D405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1503 CERAMIC CAP . B K 2200pF/500V CCD2JKS0B222 D406 SWITCHING DIODE 1SS133(T-77)
  • Page 85 Ref. No. Description Part No. Ref. No. Description Part No. D1013 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC201 IC TL3472CDR NSZBA0TTY115 D1045 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC601# PHOTO COUPLER LTV817MCF NPECLTV817MF D1401 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC631 IC LD1117V NSZBA0SSS046 D1402 DIODE ZENER 7V5BSB-T26 NDTB7R5BST26 IC801 AUDIO AMP IC TDA1517P/SOT398-1/18...
  • Page 86 Ref. No. Description Part No. Ref. No. Description Part No. GLASS GLAZE RES. 1/2W J 1M Ω Q1600 FET MOS SMD TPC8214-H QF2ZTPC8214H R601# RXX2JZLZ0105 CEMENT RES. 3W K 1.2 Ω Q1650 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R602# RW031R2PG007 RES CARBON FILM T 1/4W J 560k Ω Q1651 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P...
  • Page 87 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 620 Ω RES CARBON FILM T 1/4W J 1.2k Ω R685 RRXAFR5H6200 R1049 RCX4122T1001 CHIP RES. 1/10W F 1.0k Ω R686 RRXAFR5H1001 R1050 WIRE CP STP-S-0.50 XZ40F0REN001 RES CARBON FILM T 1/4W J 1.0 Ω...
  • Page 88 JACK ASSEMBLY Ref. No. Description Part No. CHIP RES. 1/10W J 27k Ω R1653 RRXAJR5Z0273 Ref. No. Description Part No. CHIP RES. 1/10W J 10k Ω R1654 RRXAJR5Z0103 JACK ASSEMBLY 1ESA20116 CHIP RES. 1/10W J 10k Ω R1655 RRXAJR5Z0103 Consists of the following: RES CARBON FILM T 1/4W J 27k Ω...
  • Page 89 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 100k Ω R721 RRXAJR5Z0104 JK733 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 CHIP RES. 1/10W J 100k Ω R722 RRXAJR5Z0104 JK741 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 CHIP RES.

This manual is also suitable for:

22pfl3504d/f7

Table of Contents