Electrical Safety; Assembly And Adjustments; Operation - DeWalt DWD012 Operator's Manual

E N GLISH

Electrical Safety

The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your D WALT power tool is double
E
insulated in accordance with EN 60745;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D WALT service organization.
E
WARNING: NEVER use a light socket.
NEVER connect the live (L) or
neutral (N) wires to the earth
pin marked E or
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm ; the maximum length is 30 m.
2
Also refer to the table below.
Conductor size (mm )
2
0.75
1.00
1.50
2.50
4.00
Cable length (m)
7.5
Voltage Amperes Cable rating (Amperes)
220-240 0 – 2.0 6
2.1 – 3.4 6
3.5 – 5.0 6
5.1 – 7.0 10
7.1 – 12.0 15
12.1 – 20.0 20
115 0 – 2.0 6
2.1 – 3.4 6
3.5 – 5.0 6
5.1 – 7.0 10
7.1 – 12.0 15
12.1 – 20.0 20
When using a cable reel, always unwind the cable
completely.
6
.
Cable rating (Amperes)
6
10
15
20
25
15 25 30 45 60
6 6 6 6 6
6 6 6 6 6
6 6 6 10 15
10 10 10 15 15
15 15 15 20 20
20 20 20 25 –
6 6 6 6 10
6 6 6 15 15
6 10 15 20 20
10 15 20 20 25
–
15 20 25 25
20 25 – – –

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.

OPERATION

Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
Switches (fig. 1, 2)
To start the drill, depress the trigger switch; to stop
the drill, release the trigger.
A variable speed trigger switch (a) permits speed
control—the farther the trigger is depressed, the
higher the speed of the drill.
For continuous operation, press and hold the
variable speed switch, press the lock-on button (b),
then release the switch.
Based on the different applications, turn around the
speed dial(g) to control the maximum speed.
NOTE: Use lower speeds for starting holes without
a center punch, drilling in metal or plastics, driving
screws or drilling ceramics. Higher speeds are better
for drilling wood and composition boards and using
abrasive and polishing accessories.
The forward/reverse lever (c) is used for withdrawing
bits from tight holes and removing screws. It is
located above the trigger switch. To reverse the
motor, release the trigger switch FIRST and then
push the lever to the right. After any reversing
operations, return lever to forward position.
To stop continuous operation, press the switch
briefly and release it. Always switch the tool off when
work is finished and before unplugging.
Drilling
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to
the material.