Summary of Contents for Graco RentalPRO 210 262906
Page 1
Operation 332161A RentalPro 210 Electric Airless Sprayer, Lo-Boy - For portable spray applications of architectural paints and coatings - Model 262906 3300 psi (22.7 MPa, 227 bar) Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this man- ual.
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
Page 3
Check hoses and parts for signs of damage. Replace any damaged hoses or parts. • This system is capable of producing 3300 psi (22.7 MPa, 227 bar). Use Graco replacement parts or accessories that are rated a minimum of 3300 psi (22.7 MPa, 227 bar).
Page 4
Do not kink or over-bend the hose. • Do not expose the hose to temperatures or to pressures in excess of those specified by Graco. • Do not use the hose as a strength member to pull or lift the equipment.
Component Identification Component Identification Suction Hose Pressure Control Drain Hose ON/OFF switch Fluid Hose Hour Meter Power Cord Fluid Outlet Guard Prime Valve Trigger Safety Lock Pump Serial Number ID Label 332161A...
Pressure Relief Procedure Pressure Relief Procedure Follow the Pressure Relief Procedure whenever 3. Turn prime valve down. If you suspect spray tip or you see this symbol. hose is clogged or pressure is not fully relieved, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure.
Grounding Grounding Extension Cords • Use an extension cord with an undamaged ground contact. • If an extension cord is necessary, use a 3-wire, 12 AWG (2.5 mm ) minimum. The equipment must be grounded to reduce the risk of static sparking.
Page 8
Setup Setup 1. Connect Graco airless hose to sprayer. Tighten 6. Fill throat packing nut with TSL to prevent securely. premature packing wear. Do this each time you spray. ti5735b ti3307a ti20402a 7. Turn power OFF. 2. Connect other end of hose to gun.
Page 9
Startup Startup 1. Turn pressure control to lowest pressure. 6. Inspect for leaks. Do not stop leaks with hand or a rag! If leaks occur, perform Pressure Relief Procedure, page 6. Tighten fittings. 7. Place siphon tube in paint pail. ti20417a 2.
Startup Spray Test Pattern Clearing Clogs 1. Spray test pattern. Adjust pressure to eliminate heavy edges. 1. Release trigger, put safety ON. Rotate Spray Tip. Take safety OFF. Trigger gun to clear clog. Heavy Edges ti20404a ti20409a ti20413a ti20419a 2. Use smaller tip size if pressure adjustment cannot 2.
Page 11
Cleanup Cleanup 7. Stop triggering gun. Move gun to waste pail, hold gun against pail, trigger gun to thoroughly flush system. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Pro- cedure when you stop spraying and before cleaning, checking, or servicing the equipment.
Cleanup 11. Turn pressure control knob all the way down and ™ Power Flush power switch OFF. Unplug sprayer. Power flushing is a faster method of flushing. It can only ti5316a be used after spraying water-based coatings. ti4296a ti20417a This equipment stays pressurized until pressure is 12.
Page 13
Cleanup 6. Turn on water. Rinse paint off suction tube, prime 11. Remove paint from hose. tube and inlet screen. Close valve. a. Pull and hold gun trigger. Point gun into paint pail. b. Turn power switch ON to begin pumping paint in hose back into paint pail.
Page 14
Cleanup 14. Circulate water through sprayer, into waste pail, 18. Close drain valve. Turn power ON. Trigger gun into for 20 seconds. flushing pail to purge fluid from hose. 15. Turn power switch OFF. ti5303a ti5316a ti20407a Flush 19. Turn pressure control knob all the way down and power switch OFF.
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
Need help?
Do you have a question about the RentalPRO 210 262906 and is the answer not in the manual?
Questions and answers