Page 1
Service Manual Microwave Oven Model :KOG-371G0S KOG-391G0S KOG-371H0S KOG-391H0S KOG-376T1S KOG-396T1S KOG-371R0S KOG-391R0S KOG-374R0S KOG-375R0S KOG-373R0S KOG-393R0S Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information,please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr).
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5) Evidence of dropping or abuse.
SAFETY AND PRECAUTIONS 1. FOR SAFE OPERATION Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.) 1) A broken door hinge.
2. FEATURE DIAGRAM 1) KOG-371G/H0S, KOG-391G/H0S 1. DOOR SEAL - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2. REFLECTOR(Insulator Heater) 3. HEATING ELEMENT 4. OVEN CAVITY 5. SEFETY INTERLOCK SYSTEM 6. DOOR RELEASE BUTTON - By pushing this button the latch system cut off all circuits and stops the oven before the door is opened.
Page 8
2) KOG-376T1S, KOG-396T1S 1. DOOR SEAL - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2. REFLECTOR(Insulator Heater) 3. HEATING ELEMENT 4. OVEN CAVITY 5. SEFETY INTERLOCK SYSTEM 6. CONTROL PANEL 7. METAL RACK 8.
Page 9
3) KOG-371R0S, KOG-391R0S 1. DOOR SEAL - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2. REFLECTOR(Insulator Heater) 3. HEATING ELEMENT 4. OVEN CAVITY 5. SEFETY INTERLOCK SYSTEM 6. CONTROL PANEL 7. DOOR OPENING BUTTON 8.
Page 10
4) KOG-374R0S 1. DOOR SEAL - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2. REFLECTOR(Insulator Heater) 3. HEATING ELEMENT 4. OVEN CAVITY 5. SEFETY INTERLOCK SYSTEM 6. METAL RACK 7. COUPLER - This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.
Page 11
5) KOG-375R0S 1. DOOR SEAL - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2. REFLECTOR(Insulator Heater) 3. HEATING ELEMENT 4. OVEN CAVITY 5. SEFETY INTERLOCK SYSTEM 6. METAL RACK 7. COUPLER - This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.
Page 12
6) KOG-373R0S, KOG-393R0S 1. DOOR SEAL - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2. REFLECTOR(Insulator Heater) 3. HEATING ELEMENT 4. OVEN CAVITY 5. SEFETY INTERLOCK SYSTEM 6. METAL RACK 7. COUPLER - This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.
3. CONTROL PANEL 1) KOG-371G0S, KOG-391G0S Def. Grill Combi Timer/g 1. BREAD 2. SOUP Auto 3. BAKED POTATO Cook 4. FRESH VEGETABLE 5. FROZEN VEGETABLE Pasta Frozen Pizza Beverage Auto Defrost Fish Poultry Meat COMBI GRILL Defrost Kitchen Power Clock...
Page 14
2) KOG-371H0S, KOG-391H0S Def. Grill Combi Timer/g Frozen Pizza Fresh Vegetable Beverage Dish Warmer Pasta Auto Defrost Fish Poultry Meat COMBI GRILL Defrost Kitchen Power Clock Timer STOP/ START/ CLEAR SPEEDY COOK 1. TIME SET PAD - Used to set the cooking time and the present time. 2.
Page 15
3) KOG-376T1S, KOG-396T1S 1. Display - Cooking time, power level, indicators and present time are displayed. 2. Clock - Used to set clock. 3. Start/Easy Cook - Used to start operation, also for easy start (each press adds 30 seconds microwave cooking time).
Page 16
4) KOG-371R0S, KOG-391R0S DEF. Grill Combi Grill/Combi Power/Def. Auto cook 1. Dinner plate 2. Soup 3. Beverage 4. Fresh vegetable Start/ Easy cook Stop/Clear Weight/ Time Clock 1. Display - Cooking time, power level, indicators and present time are displayed. 2.
Page 17
4) KOG-374R0S Power/Def Grill/Combi Clock Auto Cook 1. Dinner Plate 2. Soup 3. Beverage 4. Fresh Vegetable Stop/Clear Start/Easy Cook 1. Display - Cooking time, power level, indicators and present time are displayed. 2. Grill/Combi - Used to cook GRILL or COMBI. 3.
Page 18
4) KOG-375R0S Power/Def Grill/Combi Clock 1. Dinner Plate Auto Cook 2. Soup 3. Beverage 4. Fresh Vegetable Stop/Clear Start/Easy Cook 1. Display - Cooking time, power level, indicators and present time are displayed. 2. Grill/Combi - Used to cook GRILL or COMBI. 3.
Page 19
5) KOG-373R0S, KOG-393R0S KOG-373R Auto cook 1. Dinner Plate 2. Soup 3. Beverage 4. Fresh Vegetable Grill/Combi Power/ Defrost Clock DEF. Grill Combi Stop/ Clear Start/ Easy cook 1. Display - Cooking time, power level, indicators and present time are displayed. 2.
• This appliance is supplied with cable of special type, which, if damaged, must be reparied with cable of same type. Such a cable can be purchased from DAEWOO and must be installed by Qualified Person. 6. Examine the oven after unpacking for any damage such as: A misaligned door, broken door or a dent in cavity.
OPERATION AND FUNCTIONS 1. Connect the main lead to an electrical outlet. 2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking. 3.
DISASSEMBLY AND ASSEMBLY Cautions to be observed when trouble shooting Unlike many other appliances, the microwave oven is a high-voltage, high-current equipment. It is completely safety during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit. You are asked to observe the following precautions carefully.
Page 23
DISASSEMBLY AND ASSEMBLY 1. To remove cabinet. 1) Remove three screws on cabinet back. 2) Push the cabinet backward. 2. To remove door assembly. 1) Remove a screw which secure the stopper hinge top. 2) Remove the door assembly from top plate of cavity. 3) Reverse the above for reassembly.
Page 24
In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 3. To remove door parts. (1) KOG-371G0S/371H0S/371R0S REF. NO PART CODE...
Page 25
1) Remove the gasket door from door plate. 2) Remove the barrier screen inner from door plate. 3) Remove the door frame from door plate. 4) Remove the stopper hinge top from door plate. 5) Remove the spring and the hook. 6) Remove the supporter barrier screen outer from door frame.
Page 26
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (3) KOG-376T1S REF.
Page 27
1) Remove the gasket door from door plate. 2) Remove a screw which secure the door plate and door frame. 3) Remove the door frame from door plate. 4) Remove the stopper hinge top from door plate. 5) Remove the spring and the hook. 6) Remove the supporter barrier screen outer from door frame.
Page 28
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (5) KOG-374R0S REF NO.
Page 29
(1) Remove the gasket door from door weld as. (2) Remove the barrier screen inner from weld as. (3) Remove the door frame from door weld as. (4) Remove the stopper hinge top from door weld as. (5) Remove the spring and the hook. (6) Remove the barrier screen outer from door frame.
Page 30
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (6) KOG-375R0S REF NO.
Page 31
4. Method to reduce the gap between the door seal and the oven front surface. (1) To reduce gap located on part ‘A’ • Loosen two screws on stopper hinge top, and then push the door to contact the door seal to oven front surface.
Page 32
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (7) KOG-373R0S REF.
Page 33
1) Remove the gasket door from door plate. 2) Remove the barrier screen inner from door plate. 3) Remove the door frame from door plate. 4) Remove the stopper hinge top from door plate. 5) Remove the spring and the hook. 6) Remove the supporter barrier screen outer from door frame.
Page 34
In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 5. To remove control panel parts. (1) KOG-371G0S/371H0S REF. NO PART CODE...
Page 35
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly.
Page 36
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly.
Page 37
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (7) KOG-374R0S REF NO.
Page 38
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (8) KOG-375R0S REF NO.
Page 39
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (9) KOG-373R0S REF.
Page 40
1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. 2) Remove the door open lever from the control panel. 3) Remove four screws which secure the PCB assembly to control panel. 4) Disconnect membrane tail from the connector of the PCB assembly.
Page 41
8. To remove wind guide assembly. 1) Remove a screw for earthing. 2) Remove the noise filter from the wind guide. 3) Remove a screw which secure the wind guide assembly. 4) Draw forward the wind guide assembly. 5) Pull the fan from the motor shaft. 6) Remove two screws which secure the motor shaded pole.
Page 42
10. To remove tray motor. (1) Remove the coupler in the cavity. (2) Turn the set upside down. (3) Cut the tray motor cover part from the base plate. (4) Remove the tray motor cover. (5) Remove a screw which secure the tray motor. (6) Remove the tray motor.
Page 43
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 12. To remove heater parts. REF.
INTERLOCK MECHANISM AND ADJUSTMENT The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
Page 45
INTERLOCK MECHANISM AND ADJUSTMENT The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE Following the procedure below to check if the oven is defective or not. 1) Check earthing before trouble checking. 2) Be careful of the high voltage circuit. 3) Discharge the high voltage capacitor. 4) When checking the continuity of the switches, fuse or high voltage tranformer, disconnect one load wire from these parts and check continuity with the AC plug removed.
TROUBLE SHOOTING GUIDE CONDITION CHECK RESULT CAUSE REMEDY Replace Defective Outlet has Check continuity of magnetron Continuity magnetron proper voltage Fuse does not Replace blow. Defective line Check continuity of Continuity filter board noise filter board Replace Open power Check continuity of Continuity supply cord power supply cord...
Page 48
(TROUBLE 3) No microwave oscillation even though fan motor rotates. CONDITION CHECK RESULT CAUSE REMEDY Check continuity of high microwave Continuity voltage fuse oscillation Replace high voltage fuse Continuity Replace Check continuity if high Defective high voltage capacitor terminals voltage with wires removed transformer Continuity in...
Page 49
(TROUBLE 4) The following visual conditions inditions indicate a probable defective touch control circuit or membrane switch assembly 1. Incomplete segments, 1) Segments missing. 2) Partical segments missing. 3) Digit flickering other than normal display slight flickering. 4) " :0" does not display when power is on. 2.
MEASUREMENT AND TEST 1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT Microwave output power can be checked by indirectly mmeasuring the temperature rise of a certain amount of water exposed to the microwave as directed below. PROCEDURE 1. Microwave power output measurement is made with the microwave oven supplied at rated voltage and operated at its maximum microwave power setting with a load of 100 ±...
2. MICROWAVE RADIATION TEST CAUTION 1. Make sure to check the microwave leakage before and after repair of adjustment. 2. Always start measuring of an unknown field to assure safety for operating personnel from microwave energy. 3. Do not place your hands into any suspected microwave radiation field unless the safe density level is known. 4.
3. COMPONENT TEST PROCEDURE • High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle. • It is neither necessary nor advisable to attempt measurement of the high voltage. • Before touching any oven components or wiring, always unplug the oven from its power source and discharge the capacitor.
PRINTED CIRCUIT BOARD <KOG-371G/H0S, KOG-391G/H0S> 1. CIRCUIT CHECK PROCEDURE 1. Low voltage transformer check The low voltage transformer is located on the P.C.B. Measuring condition: Input voltage: 230V / Frequency: 50Hz Terminal Voltage LOAD NO LOAD AC 25.8 V AC 28.4 V NOTE 1.
Page 57
3. When there is no microwave oscillation 1) When touching START pad, oven lamp does not turn on. Fan motor do not rotate, but cook indicator in display comes on. Cause : RELAY 2 does not operate. refer to Circuit Diagram (point 3) - Check method POINT STATE...
In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 3. P.C.B. LOCATION NO (1) KOG-371G0S/371H0S NAME SYMBOL...
Page 60
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-391G0S/391H0S NAME SYMBOL SPECIFICATION...
Page 61
PRINTED CIRCUIT BOARD <KOG-376T1S, KOG-396T1S> 1. CIRCUIT CHECK PROCEDURE 1. Low voltage transformer check The low voltage transformer is located on the P.C.B. Measuring condition : Input voltage : 230V/Frequency : 50Hz Terminal Voltage LOAD NO LOAD 8 - 9 AC 23V AC 27.7V 6 - 7...
Page 63
3. When there is no microwave oscillation 1) When touching START pad, oven lamp does not turn on. Fan motor do not rotate, but cook indicator in display comes on. Cause : RELAY 2 does not operate. refer to Circuit Diagram (point 3) - Check method POINT STATE...
Page 65
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 3. P.C.B. LOCATION NO (1) KOG-376T1S NAME SYMBOL...
Page 66
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-396T1S NAME SYMBOL SPECIFICATION...
Page 67
PRINTED CIRCUIT BOARD <KOG-371R0S, KOG-391R0S> 1. CIRCUIT CHECK PROCEDURE 1. Low voltage transformer check The low voltage transformer is located on the P.C.B. Measuring condition: Input voltage: 230V / Frequency: 50Hz Terminal Voltage LOAD NO LOAD AC 25.8 V AC 28.4 V NOTE 1.
Page 69
3. When there is no microwave oscillation 1) When touching START pad, oven lamp does not turn on. Fan motor do not rotate, but cook indicator in display comes on. Cause : RELAY 2 does not operate. refer to Circuit Diagram (point 3) - Check method POINT STATE...
Page 71
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 3. P.C.B. LOCATION NO (1) KOG-371R0S NAME SYMBOL...
Page 72
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-391R0S NAME SYMBOL SPECIFICATION...
Page 73
PRINTED CIRCUIT BOARD <KOG-374R0S, KOG-375R0S> 1. CIRCUIT CHECK PROCEDURE 1. Low Voltage Transformer check • The low voltage transformer is located on the P.C.B. • Measuring condition: input voltage : 230V/Frequency : 50Hz Terminal Voltage LOAD NO LOAD AC 25.8 V AC 28.4 V NOTE : 1.
Page 75
3. When there is no microwave oscillation 1) When touching START pad, oven lamp does not turn on. Fan motor do not rotate, but cook indicator in display comes on. Cause : RELAY 2 does not operate. refer to Circuit Diagram (point 3) - Check method POINT STATE...
Page 77
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 3. P.C.B. LOCATION NO (1) KOG-374R0S/375R0S NAME NAME...
Page 78
PRINTED CIRCUIT BOARD <KOG-373R0S, KOG-393R0S> 1. CIRCUIT CHECK PROCEDURE 1. Low Voltage Transformer check • The low voltage transformer is located on the P.C.B. • Measuring condition: input voltage : 230V/Frequency : 50Hz Terminal Voltage LOAD NO LOAD AC 25.8 V AC 28.4 V NOTE : 1.
Page 80
3. When there is no microwave oscillation 1) When touching START pad, oven lamp does not turn on. Fan motor do not rotate, but cook indicator in display comes on. Cause : RELAY 2 does not operate. refer to Circuit Diagram (point 3) - Check method POINT STATE...
Page 82
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 3. P.C.B. LOCATION NO (1) KOG-373R0S NAME NAME...
Page 83
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-393R0S NAME NAME SYMBOL...
EXPLODED VIEW AND PARTS LIST <KOG-371G/H/R0S, KOG-391G/H/R0S> 1. DOOR ASSEMBLY Refer to Disassembly and assembly 2. CONTROL PANEL ASSEMBLY Refer to Disassembly and assembly 3. TOTAL ASSEMBLY...
Page 85
In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (1) KOG-371G0S/371H0S/371R0S REF NO...
Page 86
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) REF NO PART CODE PART NAME DESCRIPTION...
Page 87
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-391G0S/391H0S/391R0S REF NO PART CODE PART NAME...
Page 88
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) REF NO PART CODE PART NAME DESCRIPTION...
Page 89
EXPLODED VIEW AND PARTS LIST <KOG-376T1S, KOG-396T1S> 1. DOOR ASSEMBLY Refer to Disassembly and assembly 2. CONTROL PANEL ASSEMBLY Refer to Disassembly and assembly 3. TOTAL ASSEMBLY (1) KOG-376T1S...
Page 90
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-391G0S/391H0S/391R0S REF NO PART CODE PART NAME...
Page 91
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) REF NO PART CODE PART NAME DESCRIPTION...
Page 93
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (1) KOG-396T1S PART CODE PART NAME DESCRIPTION...
Page 94
EXPLODED VIEW AND PARTS LIST <KOG-374R0S> 1. DOOR ASSEMBLY Refer to Disassembly and assembly 2. CONTROL PANEL ASSEMBLY Refer to Disassembly and assembly 3. TOTAL ASSEMBLY (1) KOG-374R0S...
Page 95
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (1) KOG-374R0S PART CODE PART NAME DESCRIPTION...
Page 96
EXPLODED VIEW AND PARTS LIST <KOG-375R0S> 1. DOOR ASSEMBLY Refer to Disassembly and assembly 2. CONTROL PANEL ASSEMBLY Refer to Disassembly and assembly 3. TOTAL ASSEMBLY (1) KOG-375R0S...
Page 97
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (1) KOG-375R0S PART CODE PART NAME DESCRIPTION...
Page 98
EXPLODED VIEW AND PARTS LIST <KOG-373R0S, KOG-393R0S> 1. DOOR ASSEMBLY Refer to Disassembly and assembly 2. CONTROL PANEL ASSEMBLY Refer to Disassembly and assembly 3. TOTAL ASSEMBLY...
Page 99
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (1) KOG-373R0S REF NO PART CODE PART NAME...
Page 100
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) REF NO PART CODE PART NAME DESCRIPTION...
Page 101
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) (2) KOG-393R0S REF NO PART CODE PART NAME...
Page 102
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) REF NO PART CODE PART NAME DESCRIPTION...