Advertisement
Quick Links
REARSIGHT CAMERA SYSTEM
INSTALLATION INSTRUCTIONS
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . 2
SYSTEM LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
REASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INSTALLATION TIPS . . . . . . . . . . . . . . . . . . . . . . . . 10
MENU FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 11
Form #5165, Rev. B, 02-17-11
250-8192 & 250-8052
CONTENTS
CAUTION: To minimize risk
of injury from contact with the
monitor during an accident,
always wear your seat belt.
Advertisement
Related Manuals for Rostra 250-8192
Summary of Contents for Rostra 250-8192
-
Page 1: Table Of Contents
REARSIGHT CAMERA SYSTEM 250-8192 & 250-8052 INSTALLATION INSTRUCTIONS CONTENTS PARTS IDENTIFICATION ..... . 2 SYSTEM LAYOUT ......3 INSTALLATION . -
Page 2: Parts Identification
PARTS IDENTIFICATION UANTITY UMBER ESCRIPTION 2508203 REARSIGHT MONITOR MONITOR EXTENSION HARNESS MONITOR STAND (not shown) FORM #5165 INSTALLATION MANUAL (not shown) 2508110 REAR CAMERA ASSEMBLY 2508530 CAMERA RCA & POWER HARNESS 2508511 CAMERA A/V EXTENSION HARNESS 2508509 SACK PARTS: TIE STRAPS, T-TAPS, SEALING PUTTY 250-8133 REARSIGHT MONITOR &... -
Page 3: System Layout
SYSTEM LAYOUT DIAGRAM A LCD Monitor Monitor Harness Camera Splitter Harness 6 ACCESSORY POWER GROUND REVERSE LIGHT POWER CAMERA 5 VEHICLE PREPARTION Before beginning installation, familiarize yourself with the installation instructions and the REAR SIGHT camera system components. To ensure your safety: A) Apply the emergency brake. -
Page 4: Installation
INSTALLATION STEP 1: HARNESS CONNECTIONS 1. ROUTE HARNESSES TO BE JOINED WITH VIDEO 2 (VIDEO 2 ALLOWS REVERSE OVERIDE TO FUNCTION) RCA, AUDIO RCA & DC POWER CONNECTOR HARNESS AS PER DIAGRAM. USE PROVIDED WIRE TIES TO SECURE WIRING HARNESS AWAY FROM MOVING PARTS AND SHARP EDGES. - Page 5 INSTALLATION STEP 2A: STEM MOUNTED MONITOR 1. REMOVE EXISTING REARVIEW MIRROR FROM VEHICLE. FIGURE 2. 2. MOUNT REARSIGHT MONITOR ON WINDSHIELD LUG AND TIGHTEN SCREW. FIGURE 3. ROUTE CAMERA EXTENSION HARNESS TO THE BACK OF VEHICLE. 3. SECURE HARNESSES WITH WIRE TIES.
- Page 6 2. USE AN ALCOHOL PAD TO CLEAN THE DASH AREA AND BASE OF PEDESTAL SELECTED FOR INSTALLATION. (IN THE EVENT THE DASH HAS BEEN WIPED WITH A SILICON PRODUCT AN ACTIVATOR MAY BE REQUIRED TO REMOVE THE EFFECTS OF THE SILICON MATERIAL.) 3.
- Page 7 INSTALLATION STEP 3: MOUNTING CAMERA FIGURE 4 TOP OF CAMERA MICROPHONE ON RIGHT 1. WHEN MOUNTING THE CAMERA CHOOSE A LOCATION THAT MEETS SOME VERY IMPORTANT REQUIREMENTS. • CAMERA IS MOUNTED IN MANNER THAT PROVIDES A CLEAR VIEW FOR THE BACK OF THE VEHICLE.
- Page 8 • USE BRACKET FOR TEMPLATE TO MOUNT CAMERA AT OUTERMOST POINT OF FRAME. • ASSEMBLE CAMERA AS SHOWN. ANGLE CAMERA FULLY TO THE GROUND IN ORDER TO SEE BUMPER OF TRUCK. FIGURE 5 2. ALWAYS UTILIZE STANDARD PRACTICE OF VEHICLE WIRE ROUTING WHEN ROUTING CABLES.
-
Page 9: Figure
• ROUTE CABLES INSIDE WALL OF TRUCK FIGURE 7 BODY TO PREVENT ANY DAMAGE TO CIRCUITS. (FIGURE 7) INSIDE OF WALL • ROUTE WITH EXISTING CABLES AT EXITS AT THE BOTTOM OF THE BOX AND ALONG FRAME RAIL WIRE TIE CIRCUITS AT A MINIMUM AT THE OEM FREQUENCY. -
Page 10: Testing
TESTING AND REASSEMBLY TESTING 1. RECONNECT NEGATIVE BATTERY CABLE AND TORQUE TO 3 FT*LBS. RE-ENTER ANY THEFT DETERRENT INFORMATION, IF APPLICABLE. 2. TURN THE IGNITION SWITCH ON. PRESS THE MENU BUTTON TO SWITCH FROM VIDEO 1 TO VIDEO2. VERIFY THAT THE REARSIGHT MONITOR IS ON AND THE CAMERA’S PICTURE APPEARS. -
Page 11: Menu Functions
PAGE 11... - Page 12 PAGE 12...