Page 1 Viper SRT10 2 0 1 0 O W N E R ’ S M A N U A L COUPE & ROADSTER...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler Group LLC shall be deemed to be deleted and features and equipment that are either standard or op- the name Chrysler Canada Inc.
Page 3 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 4 Chrysler Group LLC 10ZB27-126-AA First Edition Printed in U.S.A.
Page 5: Table Of Contents
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 7 INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 8: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 9 INTRODUCTION 5...
Page 10: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 11: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Illuminated Entry ..... . 17 ▫...
Page 14 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ General Information ....23 Occupant Restraints ..... 32 ▫...
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Safety Checks You Should Make Inside The Break-In Recommendations ....63 Vehicle ......65 Safety Tips .
Page 16: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS 6. Release the clutch pedal. You can insert the double-sided keys into the locks with either side up. The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle’s locks.
Page 17: Key-In-Ignition Reminder
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: The Power Accessory Delay feature allows you VEHICLE SECURITY ALARM SYSTEM to operate the radio and the power windows for two The Vehicle Security Alarm monitors the doors, trunk/ minutes after turning OFF the ignition switch. Removing liftgate, and hood for unauthorized entry and the ignition the key from the ignition switch and opening the driver’s switch for unauthorized operation.
Page 18 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE arm itself in approximately 16 seconds. During the NOTE: • The system will not cancel the arming process if you arming process, the Vehicle Security Light will flash at a fast rate. Once the system is armed, the light will flash open the hood or trunk/liftgate.
Page 19: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Press the TRUNK button on the RKE transmitter to allow To Disarm the System access without triggering the alarm or having to disarm There are two ways to disarm the system: the system. The trunk lid will pop open. •...
Page 20: Electronic Immobilization System - Canada Only
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Press the UNLOCK button on the RKE transmitter. Electronic Immobilization System — Canada Only The front and rear park lights and the turn signal The Electronic Immobilization system prevents unautho- lights will flash to acknowledge the signal. rized vehicle operation by disabling the engine.
Page 21: Illuminated Entry
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 the door. At this time the Vehicle Security Alarm will ILLUMINATED ENTRY also arm itself in approximately 16 seconds. The interior lights will turn on whenever a door is opened or the liftgate is opened (Coupe models) and the •...
Page 22: Remote Keyless Entry (Rke)
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually. REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors, open the trunk/liftgate, or activate the Panic Alarm from distances up to approximately 23 ft (7 m) using a Remote...
Page 23: To Unlock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Unlock the Doors 2. Release both buttons at the same time. Press and release the UNLOCK button on the RKE 3. Test the feature while outside of the vehicle, by transmitter once to unlock the driver’s door or twice to pressing the UNLOCK button on the RKE transmitter unlock both doors.
Page 24: To Lock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with the RKE transmitter. This feature can be turned on Alarm activated will cause the alarm to sound. Press the or turned off. To change the current setting, proceed as UNLOCK button to deactivate the Vehicle Security follows: Alarm System.
Page 25: To Unlatch The Trunk/Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 3. Test the feature while outside of the vehicle, by Using the Panic Alarm pressing the LOCK button on the RKE transmitter with The Panic Alarm unlocks the driver’s door, turns on the the ignition in the OFF/LOCK position, and the key interior lights, flashes the park lights and fog lights, and removed.
Page 26: Programming Additional Transmitters
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters 5. Within 30 seconds, press and release the LOCK button and the UNLOCK button at the same time on the new NOTE: You must have at least one programmed RKE RKE transmitter.
Page 27: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • Do not touch the battery terminals that are on the back 2. Remove and replace the battery. Avoid touching the housing or the printed circuit board. new battery with your fingers. Skin oils may cause battery deterioration.
Page 28: Door Locks
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your RKE transmitter fails to operate from a normal 3. The RKE transmitter battery may be weak or dead. distance, check for these two conditions: The expected life of the battery is a minimum of three years.
Page 29: Manual Door Lock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 WARNING! (Continued) • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be injured seriously or fatally. Don’t leave the key in the ignition.
Page 30: Power Door Locks
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks Electronic Door Lock A power door lock switch is on each door trim panel. Use This vehicle is equipped with a virtual lock system. Input this switch to lock or unlock the doors. from the outside door handle is ignored if the vehicle is virtually locked.
Page 31: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: Input from the door handles is ignored once the 5. Repeat these steps if you want to return this feature to vehicle is moving faster than 5 mph (8 km/h). its previous setting. Automatic Door Locks Programming This feature can also be disabled at an authorized deal- The Automatic Door Locks feature can be enabled or...
Page 32 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The window will lower slightly if it is closed com- NOTE: • The Power Accessory Delay feature allows you to pletely when opening the door. The window will operate the power windows for two minutes after return to its fully closed position after closing the door.
Page 33: Auto-Down Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To open the window to a desired position, press and hold the WINDOW switch in the first detent. Release the switch when you want the window to stop. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
Page 34 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE second. The parking lights and turn signal lights will The word “DECK” will flash in the odometer when the flash three times to acknowledge the signal. liftgate is open. With the key in the ignition switch, this display will turn off approximately 40 seconds after NOTE: Pressing the UNLOCK button on the RKE...
Page 35: Trunk Lock And Release - Convertible Models Only
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Gas props support the liftgate in the open position. Delay feature is active, it will turn off approximately However, because the gas pressure drops with tempera- 40 seconds after the delay feature times out. ture, it may be necessary to assist the props when NOTE: Gas props support the trunk lid in the open opening the liftgate in cold weather.
Page 36: Trunk Emergency Release
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Emergency Release OCCUPANT RESTRAINTS The trunk of your vehicle is equipped with an emergency Some of the most important safety features in your release handle. It is located on the inside of the trunk lid, vehicle are the restraint systems: near the latch, and is coated so that it glows in a darkened •...
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 way out and then adjusting the belt to the desired WARNING! length to restrain a child seat or secure a large item in a seat — if equipped In an accident, you and your passengers can suffer much greater injuries if you are not properly buckled If you will be carrying children too small for adult-sized up.
Page 38: Lap/Shoulder Belts
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of ejection and the risk of injury caused by striking the WARNING! (Continued) inside of the vehicle. Everyone in a motor vehicle should • Do not allow people to ride in any area of your be belted at all times.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.
Page 40 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury. A belt worn under the arm can cause internal injuries.
Page 42: Lap/Shoulder Belt Untwisting Procedure
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. To release the belt, push the red button in the buckle. WARNING! The belt will retract automatically to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow it to retract fully.
Page 43: Enhanced Seat Belt Use Reminder System (Beltalert )
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 1. Position the latch plate as close as possible to the buckle the seat belt. The driver should also instruct all anchor point. other occupants to buckle their seat belts. Once the warning is triggered, BeltAlert will continue to chime 2.
Page 44 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert Programming 5. Within 60 seconds of turning the ignition switch to the BeltAlert can be enabled or disabled by your authorized ON/RUN position, unbuckle and then re-buckle the dealer or by performing the following steps: driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
Page 45: Automatic Locking Retractors (Alr) Mode - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Automatic Locking Retractors (ALR) Mode — 3. Allow the belt to retract. As the belt retracts, you will If Equipped hear a clicking sound. This indicates the safety belt is In this mode, the shoulder belt is automatically pre- now in the Automatic Locking Mode.
Page 46: Seat Belts And Pregnant Women
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat Seat Belt Extender belt placement by the occupant. The seat belt still must be If a seat belt is too short, even when extended fully, your worn snugly and positioned properly.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 systems. The driver’s Advanced Front Airbag is mounted NOTE: These airbags are certified to the new Federal in the steering wheel. The passenger’s Advanced Front regulations for Advanced Airbags. The passenger’s Ad- Airbag is mounted underneath a cover in the passenger’s vanced Front Airbag is certified to the Federal regulations side of the instrument panel.
Page 48 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Do not put anything on or around the airbag • Relying on the airbags alone could lead to more covers or attempt to open them manually. You may severe injuries in a collision.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 • After any accident, the vehicle should be taken to an While the seat belts are designed to protect the driver and passenger in many types of collisions, the airbags will authorized dealer immediately. deploy in certain frontal collisions depending on the Airbag System Components severity and type of collision.
Page 50 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, airbag deployment can cause severe injury or death to an and Seat Track Position Sensors infant in this position. Refer to “Passenger Airbag Dis- abled (PAD) Indicator Light”.
Page 51: Airbag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 safety seat or booster seat. If too large for a booster seat, Airbag Deployment Sensors and Controls the child should wear the lap/shoulder belt properly. Occupant Restraint Controller (ORC) 8. Read the instructions provided with your child re- The ORC is part of a Federally regulated safety system straint to make sure that you are using it properly.
Page 52 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Airbags are designed to provide addi- Seat belts are necessary for your protection in all acci- tional protection by supplementing the seat belts in dents, and also are needed to help keep you in position, certain frontal collisions depending on the severity and away from an inflating airbag.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Light”). If the ORC detects a malfunction in any part of Driver Airbag/Passenger Airbag Inflator Units the system, it turns on the Airbag Warning Light either The Driver Airbag Inflator Unit is mounted in the steer- momentarily or continuously.
Page 54 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Occupant Classification Module (OCM) fault will occur which turns on both the PAD Indicator The Occupant Classification Module (OCM) is located Light and the Airbag Warning Light. Once the lodged underneath the passenger seat. The OCM uses input object is removed, the fault will be cleared automatically from the Flex Mat to classify the occupant in the passen- after a short period.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 their seat. If the PAD Indicator Light comes on when an WARNING! adult or teenager is in the passenger seat, have the passenger reposition their self in the seat until the light An infant in rear facing child safety seat, designed goes out.
Page 56 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE occupant properly. Furthermore, objects lodged under The following requirements must be strictly adhered to: the seat can prevent the occupant’s weight from being • Do not modify the passenger seat assembly or compo- measured properly and may result in the occupant being nents in any way.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • At no time should any supplemental restraint system Enhanced Accident Response System (SRS) component or SRS related component or fastener In the event of an impact causing airbag deployment, if be modified or replaced with any part except those the communication network remains intact, and the which are approved by Chrysler Group LLC/Mopar .
Page 58 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Front airbags will not deploy in all collisions. airbag inflation. These airborne particles may irritate This does not mean something is wrong with the airbag the skin, eyes, nose, or throat. If you have skin or eye system.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Maintaining Your Airbag System WARNING! (Continued) • Do not attempt to modify any part of your ad- WARNING! vanced airbag system. The airbag may inflate • Modifications to any part of the airbag system accidentally or may not function properly if modi- could cause it to fail when you need it.
Page 60: Child Restraints
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light NOTE: If the speedometer, tachometer, or any engine You will want to have the airbags ready to related gauges are not working, the Occupant Restraint inflate for your protection in a collision. The Controller (ORC) may also be disabled.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Infant and Child Restraints WARNING! • Safety experts recommend that children ride In an accident, an unrestrained child, even a tiny rearward-facing in the vehicle until they are at least baby, can become a projectile inside the vehicle. The one year old and weigh at least 20 lbs (9 kg).
Page 62 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with knees bent over the vehicle’s seat cushion while the WARNING! child’s back is against the seat back, they should use a belt-positioning booster seat. The child and belt- A rearward-facing infant restraint must not be used positioning booster seat are held in the vehicle by the in your vehicle unless the passenger airbag has been lap/shoulder belt.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • If the shoulder belt contacts the face or neck, move the Here are some tips on getting the most out of your child child closer to the center of the vehicle. Never allow a restraint: child to put the shoulder belt under an arm or behind •...
Page 64 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seat backs and cause serious personal injury. Child Restraint Tether Anchor Child restraints having tether straps and hooks for connection to tether anchors have been available for some time.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 5. Attach the tether hook to the anchor loop. 7. Return the seatback to an upright position. 8. Install the child restraint according to the manufactur- er’s directions. 9. Remove slack from the tether strap according to the child restraint manufacturer’s directions.
Page 66 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using the Vehicle Seat 4. Tighten the lap portion of the belt and allow the excess belt webbing to retract back to the retractor. If it still does not The passenger seat belt is equipped with an automatic make the child restraint secure, then secure the child locking retractor for child restraint system installation.
Page 67: Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 • Use the proper gear for your speed range. BREAK-IN RECOMMENDATIONS A long break-in period is not required for the drivetrain • Wait until the engine has reached normal operating (engine, transmission, and rear axle) in your new vehicle. temperature before driving at the recommended maxi- Following these few simple guidelines is all that is mum break-in speed.
Page 68: Safety Tips
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can •...
Page 69: Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 If you are required to drive with the trunk/liftgate open, Safety Checks You Should Make Inside the make sure that all windows are closed and the climate Vehicle control BLOWER switch is set at high speed. DO NOT Seat Belts use the recirculation mode.
Page 70 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to feel attached to the floor mat fasteners.
Page 71: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 lodged in the tread. Inspect the tread and sidewall for WARNING! (Continued) cuts and cracks. Check the wheel nuts for tightness. • Always make sure that objects cannot fall into the Check the tires (including spare) for proper pressure. driver foot well while the vehicle is moving.
Page 73: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Power Mirrors ..... . . 84 Convertible Top Operation — If Equipped ..71 ▫...
Page 74 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Lights-On Reminder ....90 ▫ Windshield Washers ....96 ▫...
Page 75: Convertible Top Operation - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 CONVERTIBLE TOP OPERATION — IF EQUIPPED CAUTION! • To insure that no damage occurs, be sure that the WARNING! vehicle is at a complete stop with the shift lever in The convertible top does not provide the structural the NEUTRAL position before lowering or raising protection that a reinforced metal roof does and the the top.
Page 76 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Depress the button located at the top of the latch and 6. Raise both sun visors if so desired. then pull the latch handle downward and rearward. 7. Open the trunk. 8. Pull the convertible top all the way back into the storage well behind the seats.
Page 77: To Raise The Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 9. Push the leading edge of the top downward to engage the downstack latch. 10. Close the trunk. To Raise the Top 1. Lower the window in each door at least one inch. 2.
Page 78 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Manually raise the convertible top until it meets the 7. From inside the vehicle, grasp the handles and pull the windshield header. convertible top toward the windshield header. Then, push the latch handle forward so that the latch hook engages the windshield receiver rod.
Page 79: Convertible Top Boot Cover Installation - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 8. Ensure that the outboard locating pins are in their 2. Lower the convertible top. Verify that the latch handle respective receiving holes in the windshield header and is placed in the detent stow position. then push the latch handle forward all the way to close 3.
Page 80 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Slide the boot cover pocket over the front corner of the 5. Tuck the boot cover underneath the leading edge of convertible top on the driver side of the vehicle. Then, the convertible top. stretch and slide the boot cover pocket over the front corner of the convertible top on the passenger side of the vehicle.
Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 6. On the passenger side of the vehicle, clip the tab under 7. Push downward on the boot cover pocket to engage the trunk lid stop and on the outer edge of the quarter the inboard tab.
Page 82 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. On the driver side of the vehicle, clip the tab under the trunk lid stop and on the outer edge of the quarter panel flange. Engaging Driver Side Tab 10. Push downward on the boot cover behind driver seat to lock down the boot cover.
Page 83: Convertible Top Boot Cover Removal And Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Convertible Top Boot Cover Removal and Storage 1. Open the trunk. 2. On the driver side of the vehicle, pull upward on the boot cover to disengage the inboard tab. Locking Boot Cover 11.
Page 84 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Unclip the tab under the trunk lid stop and on the outer edge of the quarter panel flange. Disengaging Passenger Side Tab 5. Unclip the tab under the trunk lid stop and on the outer edge of the quarter panel flange.
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 7. Fold the outer edges of the boot cover inward. Tab Under Trunk Lid Stop 6. Slide the boot cover pockets off the front corners of the Folding Outer Edges convertible top.
Page 86: Mirrors
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Fold the boot cover again. MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A pivot system allows for horizontal and verti- cal mirror adjustment. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 87: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
Page 88: Power Mirrors
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors The power mirror switch is located on the driver’s door trim panel below the door handle. Press the button marked L (left) to select the driver-side outside mirror or the button marked R (right) to select the passenger’s outside mirror.
Page 89: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 SEATS position. Then, using body pressure, move forward and Seats are a primary part of the Occupant Restraint System rearward on the seat to be sure that the seat adjusters of the vehicle. They need to be used properly for safe have latched.
Page 90: To Open And Close The Hood
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE pull the recliner control lever upward and hold it until WARNING! the seat returns to its full upright position. • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Hood Release Lever Hood Safety Catch 2. Raise the front of the hood slightly and push the safety NOTE: Assist props will raise the hood to a normal catch handle to the right. The safety catch handle is usage position.
Page 92: Lights
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • Do not leave the hood open in areas where strong Be sure the hood is fully latched before driving your gusts of wind are likely. Such a place might be by vehicle.
Page 93: Headlight Time Delay
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 To activate the delay, turn the ignition switch OFF while the headlights are still on. Then, turn off the headlights within 45 seconds. The delay interval begins when the headlight switch is turned off. If you turn the headlights, parking lights, or ignition switch ON again, the system will cancel the delay.
Page 94: Lights-On Reminder
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: This feature is standard on all Canadian vehicles and cannot be disabled. For U.S. vehicles, this feature is shipped disabled and can be enabled or disabled at a authorized dealership, if so desired. Lights-On Reminder If the headlights or parking lights are on and the ignition switch is turned OFF, a chime will sound when the...
Page 95: Turn Signals
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Turn Signals NOTE: If either light has a very fast flash rate, check for Move the multifunction lever upward or downward and a defective outside light bulb. If an indicator fails to light the corresponding turn signal indicator on the instru- when the lever is moved, it would suggest that the ment panel will flash to show proper operation of the...
Page 96 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The interior lights will turn on, remain on for about dimmer control in the multifunction lever. These lights 30 seconds, and then fade to off if any of the following are also controlled automatically by the Illuminated occur: Entry system.
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 dimmer control in the multifunction lever. This light is Instrument Panel Dimming also controlled automatically by the Illuminated Entry With the parking lights or headlights system. on, rotate the dimmer control upward to increase the brightness of the instru- Battery Saver Feature —...
Page 98: Windshield Wipers And Washers
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Light Defeat (OFF) WINDSHIELD WIPERS AND WASHERS Rotate the dimmer control to the ex- The windshield wiper/washer control lever is on treme bottom OFF position. The inte- the right side of the steering column. rior lights will remain off when the From the off position, push the windshield wiper/ doors are open.
Page 99: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. From the off position, push the windshield wiper/washer control lever upward to the first detent DEL position, and then rotate the end of the lever to select the desired delay interval.
Page 100: Mist Feature
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you activate the washer while the windshield wiper is WARNING! in the delay range, the wipers will operate in low-speed for two wipe cycles after releasing the lever and then Sudden loss of visibility through the windshield resume the intermittent interval previously selected.
Page 101: Adjustable Pedals
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
Page 102 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The adjustable pedals switch is recessed into the knee 2. Either press the adjustable pedals switch forward to bolster beneath the steering column. move the pedals forward (toward the front of the ve- hicle), or pull the switch rearward to move the pedals rearward (toward the rear of the vehicle).
Page 103: Adjustable Foot Rest
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. Adjustable Foot Rest This feature allows the driver to adjust the foot rest forward or backward and to rotate it upward or down- ward to allow for greater driving comfort.
Page 104: Electrical Power Outlets
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To adjust the pedal: One power outlet is located on the top of the floor console. To access, push downward on the top or the 1. Adjust the seat and steering column to a comfortable outlet and release.
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 An additional power outlet is located inside the center WARNING! console. Open the lid of the console to access this outlet. To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet.
Page 106: Console Features
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES CAUTION! The front console has a removable ashtray, power outlet/ • Many accessories that can be plugged in draw cigarette lighter, and power window switches. power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 107: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 STORAGE Pull outward on the handle/latch to open this compart- A glove box storage compartment is located on the ment. passenger side of the instrument panel. Opening Glove Box Storage Compartment Glove Box Storage Compartment...
Page 108: Rear Window Features
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The rear window defroster button is located on the the heating elements: climate control panel. Press this button to turn on •...
Page 109 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....107 Sales Code RAH — AM And FM Stereo Radio With CD Player And CD/DVD Changer Instrument Cluster Descriptions ... 108 Controls .
Page 110 106 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ PTY (Scan) Button ....132 Uconnect™ Multimedia (Satellite Radio) — If Equipped ......129 ▫...
Page 111: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 107 INSTRUMENT PANEL FEATURES 1 — Air Outlet 7 — Speedometer/Odometer 13 — Climate Control 2 — Sound System Speaker 8 — Oil Pressure Gauge 14 — ENGINE START Button 3 — Main Message Center 9 — Passenger Airbag Off Light 15 —...
Page 112: Instrument Cluster Descriptions
108 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he Speedometer cannot do so, then the odometer must be set at zero, and Shows the vehicle’s speed in miles- a sticker must be placed in the door jamb stating what the per-hour (mph) and kilometers-per-...
Page 113: Message Center
UNDERSTANDING YOUR INSTRUMENT PANEL 109 • The words “FLAT TIRE” will flash rapidly in the Liquid Crystal Display (LCD) Panel The LCD panel at the bottom of the speedometer displays display and a chime will sound if critically low tire specific messages for given conditions.
Page 114 110 UNDERSTANDING YOUR INSTRUMENT PANEL Front Fog Light Indicator to have the system serviced. Furthermore, if the red This indicator will illuminate when the front fog BRAKE Warning Light and the amber ABS Warning lights are on. Light are on, and the parking brake is fully released, see your authorized dealer immediately.
Page 115 UNDERSTANDING YOUR INSTRUMENT PANEL 111 does not come on when turning the key from OFF/LOCK WARNING! to ON/RUN, have the condition checked promptly. A malfunctioning catalytic converter, as referenced Certain conditions such as a loose or missing gas cap, above, can reach higher temperatures than in normal poor fuel quality, etc., may illuminate the light after operating conditions.
Page 116 112 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Leaving the hazard flashers on for extended light remains on when the parking brake is released, it periods will wear down the battery. indicates a possible hydraulic brake system malfunction. In this case, immediate repair is necessary and continued Airbag Warning Light operation of the vehicle in this condition is dangerous.
Page 117 UNDERSTANDING YOUR INSTRUMENT PANEL 113 • If the light is flashing when the engine is running, Electronic Throttle Control (ETC) Light This light will turn on briefly as a bulb check immediate service is required. If this occurs, you may when turning on the ignition switch.
Page 118 114 UNDERSTANDING YOUR INSTRUMENT PANEL As an added safety feature, your vehicle has been operating properly. The TPMS malfunction indicator is equipped with a Tire Pressure Monitoring System combined with the low tire pressure telltale. (TPMS) that illuminates a low tire pressure telltale when When the system detects a malfunction, the telltale will one or more of your tires is significantly under-inflated.
Page 119 UNDERSTANDING YOUR INSTRUMENT PANEL 115 Seat Belt Reminder Light CAUTION! If the driver does not buckle their seat belt and vehicle speed exceeds 5 mph (8 km/h), or if the The Tire Pressure Monitor System (TPMS) has been passenger does not buckle their seat belt within optimized for the original equipment tires and 10 seconds of vehicle speed exceeding 5 mph (8 km/h), wheels.
Page 120: Gauges And Indicator Lights
116 UNDERSTANDING YOUR INSTRUMENT PANEL Gauges and Indicator Lights Coolant Temperature Gauge This gauge shows the engine coolant tempera- Tachometer ture. The gauge pointer will likely show higher This gauge shows engine speed in revolutions- temperatures when driving in hot weather, up per-minute (RPM) times 1,000.
Page 121 UNDERSTANDING YOUR INSTRUMENT PANEL 117 Oil Temperature Gauge This gauge does not indicate the amount of oil in the This gauge shows the oil temperature. The engine. The engine oil level must be checked under the gauge pointer will likely show higher tempera- hood.
Page 122: Setting The Digital Clock
118 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Gauge If jump starting is required, refer to “Jump Starting This gauge shows the amount of fuel in the gas Procedures” in “What To Do In Emergencies”. tank. The reaction time of the gauge has been CAUTION! slowed to avoid needle fluctuation during pe- riods of high G force cornering.
Page 123: Clock Setting Procedure
UNDERSTANDING YOUR INSTRUMENT PANEL 119 Clock Setting Procedure 1. Turn the ignition switch to the ON/RUN or ACC position. 2. Using the point of a ballpoint pen or similar object, press either the H (HOUR) or M (MINUTE) button on the radio.
Page 124 120 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through Program Type Radio Display the ignition switch. It must be in the ON or ACC position College College to operate the radio. Country Country PTY (Program Type) Information Inform Pressing the INFO button once while in FM mode will...
Page 125 UNDERSTANDING YOUR INSTRUMENT PANEL 121 If a preset button is activated while in the PTY (Program Program Type Radio Display Type) mode, the PTY mode will be exited and the radio Soft Rhythm and Blues Soft R&B will tune to the preset station. Sports Sports Mode...
Page 126 122 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning Tone Control Press the TUNE control up or down to increase or The Bass and/or Treble controls sound for the desired decrease the frequency. If you press and hold the button, tone. Press the AUDIO button, select Bass or TREBLE, the radio will continue to tune until you release the then press SEEK + or SEEK to increase or decrease...
Page 127: Cd Player Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 123 both AM and FM. This allows a total of 10 AM and 10 FM CD Player Operation stations to be locked into memory. You can recall the NOTE: stations stored in SET 2 memory by pressing the push- •...
Page 128 124 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJT — Eject OFF, the display will show the time of day. If you insert Press the EJT button and the disc will unload and move a disc with the ignition OFF, the display will show the to the entrance for easy removal.
Page 129: Cd/Dvd Changer Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 125 Press the SEEK button to move to the next randomly Notes On Playing MP3 Files selected track. The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When Press TUNE FF to fast forward through the tracks. Press writing MP3 files, pay attention to the following restric- the FF button a second time to stop the fast forward tions.
Page 130 126 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- • Maximum number of folders: 100 sion as MP3 files. Non-MP3 files named with the *.mp3 •...
Page 131 UNDERSTANDING YOUR INSTRUMENT PANEL 127 Playback of MP3 files MPEG Sampling Fre- Bit rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, 192, contains a lot of folders or files, the radio will take more MPEG-1 Audio 160, 128, 112, 96,...
Page 132: Operation Instructions
128 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - RW/FF (CD Mode for MP3 Play) (CD Mode For MP3 Audio Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to SEEK Button (CD Mode For MP3 Play) move back through the MP3 selection.
Page 133: Uconnect™ Multimedia (Satellite Radio)
UNDERSTANDING YOUR INSTRUMENT PANEL 129 Operating Instructions - Uconnect™ Multimedia System Activation (Satellite Radio) Mode — (If Equipped) Sirius Satellite Radio service is pre-activated, and you Refer to the Uconnect™ Multimedia (Satellite Radio) may begin listening immediately to the one year of section of the Owner’s Manual.
Page 134: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
130 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification button is pushed, the ignition is turned OFF, or five Number (ESN/SID) minutes has passed since any button was pushed. The Electronic Serial Number/Sirius Identification Num- ESN/SID Access with RBP, RBU, RAZ, RB1 and ber is needed to activate your Sirius Satellite Radio RBQ Radios system.
Page 135: Selecting Uconnect™ Multimedia (Satellite) Mode In Rbp, Rbu, Raz, Rb1 And Rbq Radios
UNDERSTANDING YOUR INSTRUMENT PANEL 131 Selecting Uconnect™ Multimedia (Satellite) Mode and the bottom of the button to search down. Holding the in RBP, RBU, RAZ, RB1 and RBQ Radios TUNE button causes the radio to bypass channels until Press the MODE button repeatedly until the word the button is released.
Page 136: Using The Pty (Program Type) Button (If Equipped)
132 UNDERSTANDING YOUR INSTRUMENT PANEL erase any AM or FM pre-set memory stations. Follow the PTY (SEEK) Button memory pre-set procedures that apply to your radio. When the desired program is obtained, press the SEEK button within five seconds. The channel will change to Using the PTY (Program Type) Button the next channel that matches the program type selected.
Page 137: Reception Quality
UNDERSTANDING YOUR INSTRUMENT PANEL 133 Reception Quality CD/DVD DISC MAINTENANCE Satellite reception may be interrupted due to one of the To keep a CD/DVD in good condition, take the following following reasons. precautions: • The vehicle is parked in an underground parking 1.
Page 138: Radio Operation And Cellular Phones
134 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- Air Conditioning and Heating System lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
Page 139 UNDERSTANDING YOUR INSTRUMENT PANEL 135 Blower Control Temperature Control Use this control to regulate the Use this control to regulate the tem- amount of air forced through the sys- perature of the air inside the passenger tem in any mode you select. Turn the compartment.
Page 140 136 UNDERSTANDING YOUR INSTRUMENT PANEL The mode settings are as follows: NOTE: There is a varying temperature differential be- tween the upper and lower outlets for added comfort. • Recirculation Control The warmer air goes to the floor outlets. This feature Air is recirculated inside the vehicle.
Page 141: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 137 NOTE: The air conditioning compressor operates in this Operating Tips mode. This dehumidifies the air to help dry the wind- NOTE: Refer to the chart at the end of this section for shield. To improve fuel economy, leave in the Defrost suggested control settings for various weather condi- mode only when necessary.
Page 142 138 UNDERSTANDING YOUR INSTRUMENT PANEL • The blower air will heat faster in cold weather if you Window Fogging use only the low blower speeds for the first ten Interior fogging on the windshield can be quickly re- minutes of vehicle operation. moved by turning the mode selector to Defrost.
Page 143 UNDERSTANDING YOUR INSTRUMENT PANEL 139 Control Setting Suggestions for Various Weather Conditions...
Page 145: Starting And Operating
STARTING AND OPERATING CONTENTS ▫ Traction ......151 Starting Procedures ....144 ▫...
Page 146 142 STARTING AND OPERATING ▫ Anti-Lock Brake System ....158 ▫ Life Of Tire ......176 ▫...
Page 147 STARTING AND OPERATING 143 ▫ Materials Added To Fuel ....183 Recreational Towing (Behind Motorhome, Etc.) ....187 ▫...
Page 148: Starting Procedures
144 STARTING AND OPERATING STARTING PROCEDURES CAUTION! Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if Long periods of engine idling, especially at high present, instruct any other occupant to buckle their seat engine speeds, can cause excessive exhaust tempera- belt.
Page 149 STARTING AND OPERATING 145 NOTE: To start the engine: • You must disarm the security system in order to start 1. Fully apply the parking brake. the engine. Refer to “Security Alarm System” in “Things To Know Before Starting Your Vehicle” for 2.
Page 150: If Engine Fails To Start
146 STARTING AND OPERATING 6. Press the red ENGINE START button located on the If Engine Fails to Start instrument panel. Release the button when the engine CAUTION! starts. To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
Page 151: After Starting
STARTING AND OPERATING 147 all the way to the floor. Release the accelerator pedal and WARNING! (Continued) the ENGINE START button once the engine is running • Do not attempt to push or tow your vehicle to get smoothly. it started. Unburned fuel could enter the catalytic If the engine shows no sign of starting after two 15 sec- converter and once the engine has started, ignite ond periods of cranking with the accelerator pedal held...
Page 152 148 STARTING AND OPERATING Your vehicle is equipped with a high torque capacity dual You will find it easier to use only the lower gears for most disc clutch. The clutch pedal must be fully pressed to the city driving. For steady highway driving with light floor during each shift.
Page 153: Recommended Shift Speeds
STARTING AND OPERATING 149 into REVERSE with the ignition key OFF. This is Recommended Shift Speeds normal operation of the transmission reverse inhibitor To use your manual transmission for fuel economy it system. should be upshifted as listed below. Shift at the vehicle speeds listed for acceleration.
Page 154: Skip Shift Indicator Light
150 STARTING AND OPERATING Skip Shift Indicator Light Downshifting - Proper downshifting will improve fuel There are times when you must shift the transmis- economy and prolong engine life. sion directly from first gear into fourth gear instead To maintain a safe speed and prolong brake life, down- of from first gear into second gear.
Page 155: Driving On Slippery Surfaces
STARTING AND OPERATING 151 DRIVING ON SLIPPERY SURFACES 2. Slow down if road has standing water or puddles. Acceleration CAUTION! WARNING! Driving your vehicle through deep puddles at speeds Rapid acceleration on slippery surfaces is dangerous. over 5 mph (8 km/h), may cause water to be ingested You could lose control of the vehicle and possibly into the engine.
Page 156: Flowing/Rising Water
152 STARTING AND OPERATING Flowing/Rising Water CAUTION! • Always check the depth of the standing water WARNING! before driving through it. Never drive through Do not drive on or across a road or path where water standing water that is deeper than the bottom of is flowing and/or rising (as in storm run-off).
Page 157 STARTING AND OPERATING 153 CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 158: Power Steering
154 STARTING AND OPERATING POWER STEERING system. This noise should be considered normal, and it The standard power steering system will give you good does not in any way damage the steering system. vehicle response and increased ease of maneuverability WARNING! in tight spaces.
Page 159: Parking Brake
STARTING AND OPERATING 155 checked if a leak is suspected, abnormal noises are If necessary, add fluid to restore to the proper indicated apparent, and/or the system is not functioning as antici- level. With a clean cloth, wipe any spilled fluid from all pated.
Page 160 156 STARTING AND OPERATING To apply the parking brake, grasp the handle and pull it The “Brake System Warning Light” in the instrument rearward until you feel resistance. To release the parking cluster will turn on when the ignition is in the ON/RUN brake, grasp the handle and pull it slightly while pressing position and the parking brake is applied.
Page 161: Brake System
STARTING AND OPERATING 157 BRAKE SYSTEM for consistent operation. A compromise to using this type Your vehicle is equipped with dual hydraulic of brake pad is that the brakes may squeal slightly under brake systems. If either of the two hydraulic certain weather and operating conditions (.i.e., during systems loses normal capability, the remaining light brake applications).
Page 162: Anti-Lock Brake System
158 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Do not “ride” the brakes by resting your foot on • After going through deep water or a car wash, the pedal. This could overheat the brakes and brakes may become wet, resulting in decreased result in unpredictable braking action, longer performance and unpredictable braking action.
Page 163 STARTING AND OPERATING 159 The ABS conducts a low-speed self-test at about 12 mph WARNING! (20 km/h). If you have your foot lightly on the brake • The Anti-Lock Brake System (ABS) contains sophis- while this test is occurring, you may feel slight pedal movement.
Page 164 160 STARTING AND OPERATING All vehicle wheels and tires must be the same size and WARNING! (Continued) type as the original equipment and the tires must be • The ABS cannot prevent the natural laws of phys- properly inflated to produce accurate signals for the ics from acting on the vehicle, nor can it increase computer.
Page 165: Tire Safety Information
STARTING AND OPERATING 161 Anti-Lock Brake Warning Light TIRE SAFETY INFORMATION The “Anti-Lock Brake Warning Light” will turn Tire Markings on and stay on briefly as a bulb check when the ignition is first turned on. If the light does not turn on during starting, have it repaired promptly.
Page 166 162 STARTING AND OPERATING • LT (Light Truck) - Metric tire sizing is based on U.S. NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric design standards. P-Metric tires have the letter “P” tires is the same as for P-Metric tires except for the molded into the sidewall preceding the size designa- letters “LT”...
Page 167 STARTING AND OPERATING 163 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 168 164 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 169: Tire Identification Number (Tin)
STARTING AND OPERATING 165 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 170: Tire Terminology And Definitions
166 STARTING AND OPERATING Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 171: Tire Loading And Tire Pressure
STARTING AND OPERATING 167 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire Placard Location...
Page 172 168 STARTING AND OPERATING axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 173 STARTING AND OPERATING 169 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
Page 174 170 STARTING AND OPERATING...
Page 175: Tires - General Information
STARTING AND OPERATING 171 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 176: Tire Inflation Pressures
172 STARTING AND OPERATING Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 177 STARTING AND OPERATING 173 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
Page 178: Tire Pressures For High Speed Operation
174 STARTING AND OPERATING Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 179: Tread Wear Indicators
STARTING AND OPERATING 175 WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. DO NOT spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the...
Page 180: Life Of Tire
176 STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including, but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 181: Tire Storage
STARTING AND OPERATING 177 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • DO NOT use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 182: Snow Tires
178 STARTING AND OPERATING SNOW TIRES Refer to “Maintenance Schedule” for the proper mainte- There are no snow tires that are compatible with the nance interval. Remember, more frequent rotation is wheels on this vehicle. permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire TIRE ROTATION RECOMMENDATIONS rotation.
Page 183: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 179 TIRE PRESSURE MONITOR SYSTEM (TPMS) Low Tire Indicator If tire pressure falls below 23 psi (159 kpa), the “Low Tire Pressure Telltale” in the Message Center will illuminate, a chime will sound, and the words “LOW TIRE” will flash slowly in the Liquid Crystal Display (LCD) panel in the bottom of the speedometer.
Page 184 180 STARTING AND OPERATING TPMS Malfunction Warning CAUTION! Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not The Tire Pressure Monitor System (TPMS) has been operating properly. The TPMS malfunction indicator is optimized for the original equipment tires and combined with the low tire pressure telltale.
Page 185: Fuel Requirements
STARTING AND OPERATING 181 your vehicle to ensure that the replacement or alternate Poor quality gasoline can cause problems such as hard tires and wheels allow the TPMS to continue to function starting, stalling, and hesitations. If you experience these properly.
Page 186: Gasoline/Oxygenate Blends
182 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- Problems that result from using methanol/gasoline or lines. Properly blended reformulated gasolines will pro- E85 Ethanol blends are not the responsibility of the vide excellent performance and durability of engine and manufacturer.
Page 187: Mmt In Gasoline
STARTING AND OPERATING 183 To fix a Non-FFV vehicle inadvertently fueled once with performance in some vehicles. The manufacturer recom- E-85 perform the following: mends using gasolines without MMT. Since the MMT content of gasoline may not be indicated on the pump, •...
Page 188: Fuel System Cautions
184 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 189: Carbon Monoxide Warnings
STARTING AND OPERATING 185 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 190 186 STARTING AND OPERATING NOTE: CAUTION! (Continued) • When the fuel nozzle “clicks” or shuts off, the fuel • To avoid fuel spillage and overfilling, do not “top tank is full. off” the fuel tank after filling. When the fuel •...
Page 191: Trailer Towing
STARTING AND OPERATING 187 NOTE: NOTE: If the vehicle requires towing, make sure all four • Tighten the gas cap until you hear a “clicking” sound. wheels are off the ground. This is an indication that the gas cap is tightened GROUND CLEARANCE properly.
Page 193: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ TIREFIT Usage Precautions ... . . 194 Hazard Warning Flasher ....190 ▫...
Page 194: Hazard Warning Flasher
190 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER turn signals will flash on and off to warn oncoming traffic The Hazard Warning flasher switch is on the top of the of an emergency. Press the switch a second time to turn steering column, just behind the steering wheel.
Page 195: Tirefit Kit
WHAT TO DO IN EMERGENCIES 191 • On the highways — Slow down and use the highest WARNING! gear possible. You or others can be badly burned by hot engine • In city traffic — While stopped, put the transmission coolant (antifreeze) or steam from your radiator.
Page 196: Tirefit Storage
192 WHAT TO DO IN EMERGENCIES TIREFIT Storage TIREFIT Kit Components and Operation The TIREFIT kit is located in the trunk. 1. Sealant Bottle TIREFIT Location 2. Deflation Button — If Equipped 3. Pressure Gauge 4. Power Button...
Page 197 WHAT TO DO IN EMERGENCIES 193 5. Mode Select Knob Selecting Sealant Mode Turn the Mode Select Knob (5) to this 6. Sealant Hose (Clear with Yellow Cap) position to inject the TIREFIT Sealant 7. Air Pump Hose (Black) and to inflate the tire. Use the Sealant Hose (clear hose with the yellow cap) 8.
Page 198: Tirefit Usage Precautions
194 WHAT TO DO IN EMERGENCIES • You can use the TIREFIT air pump to inflate bicycle TIREFIT Usage Precautions tires. The kit also comes with two needles located in • Replace the TIREFIT Sealant Bottle (1) and Sealant the Accessory Storage Compartment (located on the Hose (6) prior to the expiration date (printed on the bottom of the air pump) for inflating sport balls, rafts, bottle label) to assure optimum operation of the sys-...
Page 199 WHAT TO DO IN EMERGENCIES 195 WARNING! (Continued) WARNING! (Continued) • Do not use TIREFIT or drive the vehicle under the • A loose TIREFIT kit thrown forward in a collision following circumstances: or hard stop could endanger the occupants of the vehicle.
Page 200: Sealing A Tire With Tirefit
196 WHAT TO DO IN EMERGENCIES 2. Verify that the valve stem (on the wheel with the WARNING! (Continued) deflated tire) is in a position that is near to the ground. • TIREFIT Sealant solution contains latex. In case of This will allow the TIREFIT Hoses (6) and (7) to reach the allergic reaction or rash, consult a physician im- valve stem and keep the TIREFIT kit flat on the ground.
Page 201 WHAT TO DO IN EMERGENCIES 197 3. Uncoil the Sealant Hose (6) and then remove the NOTE: Manual transmission vehicles must have the yellow cap from the fitting at the end of the hose. parking brake engaged and the shifter in NEUTRAL. •...
Page 202 198 WHAT TO DO IN EMERGENCIES 2. Connect the Power Plug (8) to a different 12 Volt Pressure Gauge (3) will decrease quickly from approxi- power outlet in your vehicle or another vehicle, if avail- mately 70 psi (5 Bar) to the actual tire pressure when the able.
Page 203 WHAT TO DO IN EMERGENCIES 199 If the tire inflates to the recommended pressure or is at CAUTION! least 26 psi (1.8 Bar) pressure within 15 minutes: • The metal end fitting from Power Plug (8) may get 1. Press the Power Button (4) to turn off the TIREFIT kit. hot after use, so should be handled carefully.
Page 204 200 WHAT TO DO IN EMERGENCIES If tire pressure is less than 19 psi (1.3 Bar) , the tire is too WARNING! badly damaged. Do not attempt to drive the vehicle further. Call for assistance. TIREFIT is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using If the tire pressure is 19 psi (1.3 bar) or higher: TIREFIT.
Page 205 WHAT TO DO IN EMERGENCIES 201 4. Have the tire inspected and repaired or replaced at the 4. Clean any remaining sealant from the TIREFIT hous- earliest opportunity at an authorized dealer or tire ser- ing. vice center. 5. Position the new Sealant Bottle (1) to the housing so 5.
Page 206: Jump-Starting Procedures
202 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES WARNING! (Continued) • Battery fluid is a corrosive acid solution; do not WARNING! allow battery fluid to contact eyes, skin, or cloth- • Take care to avoid the radiator cooling fans when- ing.
Page 207 WHAT TO DO IN EMERGENCIES 203 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles touch one another.
Page 208 204 WHAT TO DO IN EMERGENCIES post (+). Connect the other end of the same cable to the WARNING! (Continued) positive (+) terminal of the discharged battery. • Do not connect the cable to the negative post of the 8. If you are jump-starting your vehicle, connect the discharge battery.
Page 209: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 205 12. Start the engine in the vehicle with the discharged FREEING A STUCK VEHICLE battery. If engine does not start in 15 seconds, stop If your vehicle becomes stuck in mud, sand, or snow, it cranking engine and allow starter to cool down before can often be moved by a rocking motion.
Page 210: Towing A Disabled Vehicle
206 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE CAUTION! (Continued) Do not tow with sling-type equipment. Only use flatbed • Revving the engine or spinning the wheels too fast equipment. Always comply with applicable state or local may lead to transmission overheating and failure. towing ordinances.
Page 211: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Maintenance-Free Battery ....217 Engine Compartment — 8.4L ... . . 209 ▫...
Page 212 208 MAINTAINING YOUR VEHICLE ▫ Manual Transmission ....235 ▫ High Intensity Discharge Headlamps (HID) ... . 252 ▫...
Page 213: Engine Compartment - 8.4L
MAINTAINING YOUR VEHICLE 209 ENGINE COMPARTMENT — 8.4L 1 — Coolant Pressure Cap 6 — Clutch Fluid Reservoir 2 — Engine Oil Dipstick 7 — Power Steering Fluid Reservoir 3 — Power Distribution Center 8 — Engine Oil Fill 4 — Remote Jump Start Positive Battery Post 9 —...
Page 214: Onboard Diagnostic System (Obd Ii)
210 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! To meet new government regulations and promote cleaner air, your vehicle is equipped with a sophisticated Prolonged driving with the light on could cause onboard diagnostic system called OBD II. This system further damage to the emission control system.
Page 215: Emissions Inspection And Maintenance Programs
MAINTAINING YOUR VEHICLE 211 EMISSIONS INSPECTION AND MAINTENANCE Your vehicle has a simple ignition key-actuated test, PROGRAMS which you can use prior to going to the test station. To In some localities, it may be a legal requirement to pass check if your vehicle’s OBD II system is ready, you must an inspection of your vehicle’s emissions control system.
Page 216: Replacement Parts
212 MAINTAINING YOUR VEHICLE the ignition or start the engine. This means that your before going to the I/M station. The I/M station can fail vehicle’s OBD II system is not ready and you should your vehicle because the MIL is on with the engine not proceed to the I/M station.
Page 217: Maintenance Procedures
MAINTAINING YOUR VEHICLE 213 NOTE: Intentional tampering with emissions control CAUTION! systems may void your warranty and could result in civil • Failure to properly maintain your vehicle or per- penalties being assessed against you. form repairs and service when necessary could WARNING! result in more costly repairs, damage to other components or negatively impact vehicle perfor-...
Page 218: Engine Oil
214 MAINTAINING YOUR VEHICLE Engine Oil Change Engine Oil Road conditions and your kind of driving affect the Checking Oil Level interval at which your oil should be changed. Check the To assure proper engine lubrication, the engine oil must following list to see if any apply to you.
Page 219 MAINTAINING YOUR VEHICLE 215 If none of these apply to you, then change your engine oil CAUTION! at every interval shown on “Maintenance Schedule A. Refer to “Maintenance Schedule” for further information. Do not use chemical flushes in your engine oil as the chemicals can damage your engine.
Page 220: Engine Oil Filter
216 MAINTAINING YOUR VEHICLE Materials Added to Engine Oil Engine Oil Filter Selection Do not add supplemental materials, other than leak This manufacturer’s engines have a full-flow type oil detection dyes, to the engine oil. Engine oil is an engi- filter.
Page 221: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 217 Maintenance-Free Battery WARNING! The top of the maintenance-free battery is permanently sealed. You will never have to add water, nor is periodic The air induction system (air cleaner, hoses, etc.) can maintenance required. provide a measure of protection in the case of engine backfire.
Page 222 218 MAINTAINING YOUR VEHICLE To gain access to the battery, remove the floor portion of the rear compartment carpet. Battery Location Accessing The Battery...
Page 223: Battery Save Feature
MAINTAINING YOUR VEHICLE 219 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 224 220 MAINTAINING YOUR VEHICLE storage time without losing radio and engine controller 3. Push the driver’s power door lock switch in the up memory. Using this feature is an alternative to discon- direction. A single chime will sound and the horn will necting the battery.
Page 225: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 221 • The Vehicle Security Alarm is disabled when the NOTE: If the ignition switch is NOT turned to ON/ Battery Save Feature is enabled. Therefore, the vehicle RUN position, the Battery Save Feature will be enabled is not protected when the Battery Save Feature is 45 seconds after the driver’s door is closed.
Page 226 222 MAINTAINING YOUR VEHICLE NOTE: If A/C performance seems less then normal, WARNING! (Continued) check the front of the A/C condenser (located in front of • The air conditioning system contains refrigerant the radiator) for dirt and insect accumulation. Clean with under high pressure.
Page 227: Body Lubrication
MAINTAINING YOUR VEHICLE 223 Body Lubrication The external lock cylinders should be lubricated twice a Locks and all body pivot points, including such items as year, preferably in the Fall and Spring. Apply a small seat tracks, door hinge pivot points and rollers, liftgate, amount of a high quality lubricant, such as MOPAR tailgate, sliding doors and hood hinges, should be lubri- Lock Cylinder Lubricant or equivalent directly into the...
Page 228: Adding Washer Fluid
224 MAINTAINING YOUR VEHICLE NOTE: Life expectancy of wiper blades varies depend- WARNING! ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, Commercially available windshield washer solvents marks, water lines or wet spots. If any condition is are flammable.
Page 229 MAINTAINING YOUR VEHICLE 225 into the passenger compartment. In addition, inspect the CAUTION! exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required. The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- WARNING! ness of the catalyst as an emissions control device and may seriously reduce engine performance and...
Page 230 226 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your A hot exhaust system can start a fire if you park over vehicle is not kept in proper operating condition. materials that can burn. Such materials might be Have your vehicle serviced promptly in the event of grass or leaves coming in contact with your exhaust engine malfunction, particularly when involving en-...
Page 231: Cooling System
MAINTAINING YOUR VEHICLE 227 To minimize the possibility of catalytic converter dam- Cooling System age: WARNING! • Do not shut off the engine or interrupt the ignition • When working near the radiator cooling fans, when the transmission is in gear and the vehicle is in motion.
Page 232 228 MAINTAINING YOUR VEHICLE rusty in appearance, the system should be drained, Cooling System – Drain, Flush, and Refill flushed, and refilled with fresh engine coolant (anti- If the engine coolant (antifreeze) is dirty or contains a freeze). Check the front of the A/C condenser/radiator considerable amount of sediment, clean and flush with a for any accumulation of bugs, leaves, etc.
Page 233 MAINTAINING YOUR VEHICLE 229 Adding Coolant CAUTION! Your vehicle has been built with an improved engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) that allows extended maintenance specified HOAT engine coolant (antifreeze), may intervals. This engine coolant (antifreeze) can be used up result in engine damage and may decrease corro- to five years or 102,000 miles (170 000 km) before replace- sion protection.
Page 234 230 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- The cap should be inspected and cleaned if there is any ized water when mixing the water/engine coolant accumulation of foreign material on the sealing surfaces. (antifreeze) solution.
Page 235 MAINTAINING YOUR VEHICLE 231 Disposal of Used Coolant The radiator normally remains completely full, so there is Used ethylene glycol based engine coolant (antifreeze) is no need to remove the radiator cap unless checking for a regulated substance requiring proper disposal. Check engine coolant (antifreeze) freeze point or replacing en- with your local authorities to determine the disposal gine coolant (antifreeze).
Page 236: Brake System
232 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be bottle overflow hoses are not kinked or obstructed. safely driven.
Page 237 MAINTAINING YOUR VEHICLE 233 Clean the top of the master cylinder area before removing WARNING! the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reser- Riding the brakes can lead to brake failure and voir.
Page 238 234 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • To avoid contamination from foreign matter or • Use only manufacturer’s recommended brake moisture, use only new brake fluid or fluid that fluid. Refer to “Fluids, Lubricants, and Genuine has been in a tightly closed container. Keep the Parts”...
Page 239: Manual Transmission
MAINTAINING YOUR VEHICLE 235 Check the fluid level by removing the fill plug located on WARNING! (Continued) the left side of the transmission. The fluid level should be • Do not allow petroleum based fluid to contami- at the bottom of the fill hole. Add fluid, if necessary, to nate the brake fluid.
Page 240: Hydraulic Clutch
236 MAINTAINING YOUR VEHICLE Hydraulic Clutch WARNING! Master Cylinder – Clutch Fluid Level Check Overfilling the clutch fluid reservoir can result in Check the fluid in the clutch master cylinder when spilling clutch fluid on hot engine parts and the performing underhood services.
Page 241: Rear Axle
MAINTAINING YOUR VEHICLE 237 Change Clutch Fluid manufacturer’s recommended axle lubricant. Refer to Clutch fluid will tend to absorb moisture from the “Fluids, Lubricants, and Genuine Parts” in “Maintaining atmosphere over time. If the fluid becomes contaminated Your Vehicle” for further information. with water, clutch performance will deteriorate.
Page 242 238 MAINTAINING YOUR VEHICLE • Use a high quality cleaner wax, such as MOPAR passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly Cleaner Wax or equivalent to remove road film, stains, corrosive to the metal in your vehicle.
Page 243 MAINTAINING YOUR VEHICLE 239 • For tough stains, apply MOPAR scouring pads, steel wool, a bristle brush or metal pol- Total Clean or ishes. Only MOPAR cleaners or equivalent are recom- equivalent, or a mild soap solution to a clean, damp mended.
Page 244 240 MAINTAINING YOUR VEHICLE if absolutely necessary. Do not use harsh cleaners or glass cleaner. Never use an abrasive type cleaner. Use Armor All . Use MOPAR Total Clean or equivalent to caution when cleaning inside rear windows equipped with clean vinyl upholstery.
Page 245: Aero Group - If Equipped
MAINTAINING YOUR VEHICLE 241 Seat Belt Maintenance 1. Front Splitter Do not bleach, dye or clean the belts with chemical The front splitter will not flex or compress against solvents or abrasive cleaners. This will weaken the fabric. impacts from the front. If an impact does occur, have the Sun damage will also weaken the fabric.
Page 246 242 MAINTAINING YOUR VEHICLE Always leave ample room and be sure to educate anyone CAUTION! you allow to operate the vehicle. • Hard contact with steep ramps may cause damage CAUTION! to your splitter. • Replace rub strips when they are worn down to Use care when approaching parking blocks, tall 3/8 inch (10 mm) on the front edge.
Page 247 MAINTAINING YOUR VEHICLE 243 3. Carbon Fiber The clear coated carbon fiber panels will have some variation and minor waviness in the woven pattern. This is inherent to the process and a sign of its authenticity. All carbon fiber materials are susceptible to UV degra- dation during long exposure to the sun.
Page 248: Fuses
244 MAINTAINING YOUR VEHICLE FUSES Cavity Car- Mini- Description tridge Fuse Power Distribution Center Fuse The Power Distribution Center is located in the engine 40 Amp — Blower Motor compartment on the driver’s side of the vehicle. This Green center contains fuses and relays. 40 Amp —...
Page 249 MAINTAINING YOUR VEHICLE 245 Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse 30 Amp — Ignition Switch Run/ 16, 17 — 20 Amp Power Outlet Pink Accessory Feed Yellow 40 Amp — Headlights — 15 Amp Ignition Off Draw (IOD) Green...
Page 250 246 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description CAUTION! tridge Fuse • When installing the Power Distribution Center Fuse cover, it is important to ensure the cover is prop- 62, 63 — 15 Amp Gauges erly positioned and fully latched. Failure to do so Blue may allow water to get into the Power Distribution 5, 6...
Page 251: Mini-Power Distribution Center
MAINTAINING YOUR VEHICLE 247 Mini-Power Distribution Center CAUTION! The Mini-Power Distribution Center is located in the • When installing the Mini-Power Distribution engine compartment on the passenger’s side of the vehicle. This center contains radiator fan control relays Center cover, it is important to ensure the cover is and has two externally-mounted 40 Amp fuses for the properly positioned and fully latched.
Page 252 248 MAINTAINING YOUR VEHICLE • Fill the fuel tank. This will prevent water condensation • Cut blocks of plywood about the same size of the tires. inside the tank. If you plan to store your vehicle more Cover each block with indoor/outdoor carpeting and than two months, add an anti-oxidant fuel stabilizer to place them between the tires and concrete.
Page 253 MAINTAINING YOUR VEHICLE 249 terminal or use the “Battery Save Feature” to conserve Check the battery every four to six weeks to ensure that battery power. Refer to “Maintenance Procedures/ the voltage is above 12.40 Volts. The voltage will drop Battery Save Feature”...
Page 254: Replacement Bulbs
250 MAINTAINING YOUR VEHICLE properly. If not, there is a problem with a switch or the LIGHT BULBS – Exterior system. See your authorized dealer for service. (Convertible Models) Bulb Number Low/High Beam High Intensity Discharge • Cover the vehicle whenever possible to prevent acci- (HID) Headlamp .
Page 255: Bulb Replacement
MAINTAINING YOUR VEHICLE 251 BULB REPLACEMENT LIGHT BULBS – Exterior (Coupe Models) Bulb Number Auxiliary High Beam Headlamp, Front Park/Turn Low/High Beam High Intensity Discharge (HID) Signal Lamp, Front Side Marker Lamp Headlamp..Serviced at authorized dealer only 1.
Page 256: High Intensity Discharge Headlamps (Hid)
252 MAINTAINING YOUR VEHICLE 2. Turn the appropriate bulb and socket assembly coun- 3. Pull the bulb out of the socket assembly. terclockwise, and then pull it out of the headlamp 4. Push the replacement bulb into the socket assembly. assembly.
Page 257: Front Fog Lamp
MAINTAINING YOUR VEHICLE 253 Front Fog Lamp WARNING! 1. Remove the push pin from the upper outer corner of A transient high tension occurs at the bulb sockets of the splash shield and remove the splash shield. High Intensity Discharge (HID) headlamps when the headlamp switch is turned ON.
Page 258: Taillamp, Tail/Stop Lamp, Rear Marker Lamp
254 MAINTAINING YOUR VEHICLE 2. Turn the bulb and socket assembly counterclockwise, 6. Install the splash shield and push pin. and then pull it out of the front fog lamp assembly. Taillamp, Tail/Stop Lamp, Rear Marker Lamp 1. Open the trunk 2.
Page 259: Taillamp, Tail/Stop Lamp, Rear Marker Lamp (Coupe Models)
MAINTAINING YOUR VEHICLE 255 3. Turn the appropriate bulb and socket assembly coun- 4. Pull the bulb out of the socket assembly. terclockwise, and then pull it out of the upper lamp 5. Push the replacement bulb into the socket assembly. assembly.
Page 260: Backup Lamp, Rear Turn Signal Lamp
256 MAINTAINING YOUR VEHICLE Backup Lamp, Rear Turn Signal Lamp 3. Remove the three upper lamp assembly retaining nuts. 1. Open the trunk. 2. Remove the two fasteners and then remove the access panel.
Page 261 MAINTAINING YOUR VEHICLE 257 5. Remove the upper lamp assembly. 4. Remove the three bulb and socket assemblies from the upper lamp assembly by turning them counterclockwise and then pulling them out of the upper lamp assembly.
Page 262: Rear Turn Signal Lamp
258 MAINTAINING YOUR VEHICLE 6. Turn the appropriate bulb and socket assembly coun- terclockwise, and then pull it out of the lower lamp assembly. 2 — Rear Turn Signal Lamp 7. Pull the bulb out of the socket assembly. 8. Push the replacement bulb into the socket assembly. 1 —...
Page 263: License Lamp
MAINTAINING YOUR VEHICLE 259 10. Reinstall the three bulb and socket assemblies into the upper lamp assembly, and turn them clockwise. 11. Reinstall the upper lamp assembly and the three retaining nuts. 12. Install the access panel and the two fasteners. 13.
Page 264: Fluid Capacities
260 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 16 Gallons 60.6 Liters Engine Oil with Filter 8.4 Liter Engine (SAE 5W-40, API Certified) 11 Quarts 10.4 Liters Cooling System * 8.4 Liter Engine (MOPAR Engine Coolant/Antifreeze 5 16 Quarts 15 Liters Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.
Page 265: Fluids, Lubricants, And Genuine Parts
MAINTAINING YOUR VEHICLE 261 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil For best performance and maximum protection under all types of operat- ing conditions, the manufacturer only recommends full synthetic engine oils that meet the requirements of Chrysler Material Standard MS-10725 and are approved to MB 229.3 or MB 229.5.
Page 266: Chassis
262 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Transmission MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Rear Axle MOPAR Synthetic Gear and Axle Lubricant SAE 75W-140 or equivalent, with Limited Slip Additive Friction Modifier. Brake Master Cylinder MOPAR Brake and Clutch Fluid DOT 4 Motor Vehicle or equivalent.
Page 267 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..264 Maintenance Schedules ....264 ▫ Maintenance Schedule B ....267 ▫...
Page 268 264 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The Scheduled Maintenance services listed in bold type There are two maintenance schedules that show the must be done at the times or mileages specified to ensure required service for your vehicle. the continued proper functioning of the emissions control First is “Maintenance Schedule B.”...
Page 269 MAINTENANCE SCHEDULES 265 NOTE: Second is “Maintenance Schedule A.” It is for vehicles • If ANY of these apply to you then change your engine that are not operated under any of the conditions listed oil every 3,000 miles (5000 km) or three months, under “Maintenance Schedule B.
Page 270 266 MAINTENANCE SCHEDULES • Check all lights and all other electrical items for correct At Each Stop for Fuel operation. • Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level At Each Oil Change while the vehicle is on level ground will improve the •...
Page 271 MAINTENANCE SCHEDULES 267 MAINTENANCE SCHEDULE B NOTE: • If ANY of these apply to you, then change your engine Follow “Maintenance Schedule B” if you usually operate your vehicle under one or more of the following condi- oil every 3,000 miles (5000 km) or three months, tions.
Page 272 268 MAINTENANCE SCHEDULES Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if necessary.
Page 273 MAINTENANCE SCHEDULES 269 Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (35 000) (40 000) (45 000) (50 000) (55 000) (60 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if necessary.
Page 274 270 MAINTENANCE SCHEDULES Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (65 000) (70 000) (75 000) (80 000) (85 000) (90 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the engine air cleaner fil- ter, if necessary.
Page 275 MAINTENANCE SCHEDULES 271 Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (95 000) (100 000) (105 000) (110 000) (115 000) (120 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if necessary.
Page 276 272 MAINTENANCE SCHEDULES Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (95 000) (100 000) (105 000) (110 000) (115 000) (120 000) Change the transmission fluid. Inspect the brake linings. Change the rear axle fluid. Change the brake fluid. Change the brake and clutch fluid.
Page 277 MAINTENANCE SCHEDULES 273 Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if necessary.
Page 278 274 MAINTENANCE SCHEDULES Miles 93,000 96,000 99,000 102,000 105,000 108,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) (180 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the engine air cleaner fil- ter, if necessary.
Page 279 MAINTENANCE SCHEDULES 275 Miles 93,000 96,000 99,000 102,000 105,000 108,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) (180 000) Inspect the transmission fluid. Inspect the brake linings. Change the rear axle fluid. Change the brake and clutch fluid. Change the brake fluid.
Page 280 276 MAINTENANCE SCHEDULES Miles 111,000 114,000 117,000 120,000 (Kilometers) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Inspect and replace the PCV valve, if necessary.
Page 281 MAINTENANCE SCHEDULES 277 Miles 111,000 114,000 117,000 120,000 (Kilometers) (185 000) (190 000) (195 000) (200 000) Change the rear axle fluid. Change the brake and clutch fluid. Lubricate the front and rear suspension ball joints. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected.
Page 282 278 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE A Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [12] [18] [24] [30] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary.
Page 283 MAINTENANCE SCHEDULES 279 Miles 36,000 42,000 48,000 54,000 60,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) [Months] [36] [42] [48] [54] [60] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Inspect and replace the PCV valve, if necessary.
Page 284 280 MAINTENANCE SCHEDULES Miles 66,000 72,000 78,000 84,000 90,000 (Kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) [Months] [66] [72] [78] [84] [90] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary.
Page 285 MAINTENANCE SCHEDULES 281 Miles 96,000 102,000 108,000 114,000 120,000 (Kilometers) (160 000) (170 000) (180 000) (190 000) (200 000) [Months] [96] [102] [108] [114] [120] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary.
Page 286 282 MAINTENANCE SCHEDULES Miles 96,000 102,000 108,000 114,000 120,000 (Kilometers) (160 000) (170 000) (180 000) (190 000) (200 000) [Months] [96] [102] [108] [114] [120] Inspect the brake linings. Change the rear axle fluid. Change the brake and clutch fluid. Lubricate the front and rear suspension ball joints.
Page 287 MAINTENANCE SCHEDULES 283 WARNING! WARNING! (Continued) • Failure to properly inspect and maintain your • You can be badly injured working on or around a vehicle could result in a component malfunction motor vehicle. Do only service work for which you and effect vehicle handling and performance.
Page 289: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Suggestions For Obtaining Service For Your Vehicle......287 Speech Impaired (TDD/TTY) .
Page 290 286 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 293 Department Of Transportation Uniform Tire Quality Grades ......293 ▫...
Page 291: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 287 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 292: Chrysler Group Llc Customer Center
288 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (800) 423–6343 •...
Page 293: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 289 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 294: Warranty Information
290 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
Page 295: In Canada
IF YOU NEED CONSUMER ASSISTANCE 291 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 296 292 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 297 IF YOU NEED CONSUMER ASSISTANCE 293 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 298 294 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 299 INDEX...
Page 300 296 INDEX About Your Brakes ..... . . 157 Airbag On/Off Switch ..... 58 ABS (Anti-Lock Brake System) .
Page 301 INDEX 297 Jump Starting ......202 Capacities, Antifreeze (Engine Coolant) ..260 Keyless Transmitter Replacement (RKE) .
Page 302 298 INDEX Circuit Breakers ......244 Drain, Flush, and Refill ....228 Clean Air Gasoline .
Page 303 INDEX 299 Disposal Towing ......206 Antifreeze (Engine Coolant) ....231 Emission Control System Maintenance .
Page 304 300 INDEX Engine Oil Viscosity ....215,260 Flooded Engine Starting ....146 Engine Oil Viscosity Chart .
Page 305 INDEX 301 Clean Air ......181 Fuel ....... . 118 Ethanol .
Page 306 302 INDEX Time Delay ......89 Intermittent Wipers (Delay Wipers) ... . 95 Heater .
Page 307 INDEX 303 Light Bulbs ......67 High Beam ......91,109 Lights .
Page 308 304 INDEX Voltage ......118 Manual Transmission ..... 147 Loading Vehicle Fluid Level Check .
Page 309 INDEX 305 Occupant Restraints ..... 32,53 Outside Rearview Mirrors ....83 Octane Rating, Gasoline (Fuel) .
Page 310 306 INDEX Door Locks ......26 Rear Liftgate ......29 Mirrors .
Page 311 INDEX 307 Rotation, Tires ......178 Operating Instructions ....35 Pretensioners .
Page 312 308 INDEX Shoulder Belts ......34 Tachometer ......116 Signals, Turn .
Page 313 INDEX 309 Quality Grading ..... . . 293 Transmitter Battery Service Radial ......174 (Remote Keyless Entry) .
Page 314 310 INDEX Vehicle Modifications/Alterations ....7 Waxing and Polishing ..... 238 Vehicle Storage .
Page 315 Chrysler Group LLC 10ZB27-126-AB Printed in U.S.A. 2nd Edition...

Dodge Viper SRT10 ROADSTER 2010 Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Replacement Bulbs/Bulb Number

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Dodge Viper SRT10 ROADSTER 2010

Summary of Contents for Dodge Viper SRT10 ROADSTER 2010