Zenoah G3800 Owner's Manual
Hide thumbs
Also See for G3800:
- Owner's manual (15 pages) ,
- Parts list (8 pages) ,
- Service parts list (4 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for Zenoah G3800
Summary of Contents for Zenoah G3800
- Page 1 G3800 115 57 92-38 (302) OWNER’S MANUAL CHAIN SAW G3800 Original Language...
-
Page 2: Table Of Contents
G3800 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instruction Wear head, eye and ear book before operating this protection. machine. Use the chain saw Warning! Danger of with two hands. kickback. Read, understand and Never touch hot surface. follow all warnings. -
Page 3: For Safe Operation
G3800 1. For safe operation WARNING This chainsaw has been especially designed for tree maintenance and should therefore only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may 10. - Page 4 G3800 20. Operate the chain saw only in well handle, and the left hand on the front ventilated areas. Never start or run handle, when the engine is running. the engine inside a closed room or Use a firm grip with thumbs and fin-...
-
Page 5: Explanation Of Symbols On The Machine
G3800 2. Explanation of Symbols on the Machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE” Position: Fuel cap... -
Page 6: Installing Guide Bar And Saw Chain
G3800 3. Installing Guide Bar and Saw Chain A standard saw unit package contains the items as illustrated. Plug wrench Power unit (Hexagon socket (S13/S19) + Slotted driver) Screwdriver for carburetor adjustment (Slotted driver) Bar protector Guide bar Saw chain Open the box and install the guide bar and the saw 4. -
Page 7: Fuel And Chain Oil
G3800 4. Fuel and Chain Oil GB-7... -
Page 8: Operating The Engine
G3800 5. Operating the Engine It is very dangerous to run a chainsaw that 6. Allow the engine to warm up with the throttle lever mounts broken parts or lacks any parts. pulled slightly. Before starting engine, make sure that all the... - Page 9 G3800 ■ CHAIN BRAKE Carburetor anti-freeze mechanism This machine is equipped with an automatic brake to Operating chain saws in temperatures of 0 – 5°C at times of stop saw chain rotation upon occurrence of kickback high humidity may result in ice forming within the carburetor, during saw cutting.
-
Page 10: Sawing
G3800 6. Sawing ning the saw at full the throttle for I - • Before proceeding to your job, 2 seconds and pushing the front read the section “For Safe hand guard forward. The chain Operation”. It is recommended should stop immediately with the en- to first practice sawing easy gine at full speed. -
Page 11: Maintenance
G3800 A log lying on the ground First check to which side the limb is bent. Then make the initial cut from the bent side and finish by sawing from the opposite side. Be alert to the springing back of a cut limb. -
Page 12: Maintenance Of Saw Chain And Guide Bar
G3800 2. Fuel filter 3. Spark plug (a) Using a wire hook, take out the filter from the filler port. 0.6 ~ 0.7 mm Fuel filter Champion RCJ-7Y Clean the electrodes with a wire brush and reset the gap to (b) Disassemble the filter and wash with gasoline, or replace 0.65 mm as necessary. -
Page 13: Troubleshooting Guide
WARNING: 91PX 55 This saw is equipped with one of the following low Top plate cutting angle kickback bar/chain combinations: Zenoah Part Number ■ Guide Bar Bar Size Guide Bar Saw Chain 91VG 91PX • Reverse the bar occasionally to prevent partial wear. -
Page 14: Specifications
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF THE PURCHASER SHALL BEAR COSTS OF TRANS- INSTRUCTION LISTED IN THE OWNER/OPERATOR PORTING THE UNIT TO AND FROM THE ZENOAH MANUAL FOR PROPER USE AND MAINTENANCE OF DEALER. THE UNITS ACCIDENT MISHANDLING, ALTERATION,...