Related Manuals for Zenoah G3802
Summary of Contents for Zenoah G3802
- Page 1 G3802/G3802EZ 115 59 85-38 (306) OWNER’S MANUAL CHAIN SAW G3802 G3802EZ Original Language GB-1 01-G3802･3802EZ_GB_306＿三.indd 1 13.6.25 5:26:38 PM...
-
Page 2: Table Of Contents
2. Starter knob 3. Air cleaner 4. Choke knob 5. Throttle interlock 6. Right handle 7. Throttle lever 8. Engine switch 9. Fuel tank 10. Oil tank 11. Left handle 12. Saw chain 13. Guide Bar GB-2 01-G3802･3802EZ_GB_306＿三.indd 2 13.6.25 5:26:39 PM... -
Page 3: Specification
When using market oil (JASO FB grade oil or ISO-L- Size mm (in.): ..........400 (16) EGB grade oil) ......GASOLINE 25: OIL 1 When using ZENOAH genuine oil, JASO FD grade oil Saw chain: Oregon 91PX Pitch mm (in.): ..........9,53 (3/8) or ISO-L-EGD grade oil.....GASOLINE 50: OIL 1... -
Page 4: For Safe Operation
9. Always hold the chain saw firmly with fall during the felling operation. both hands when the engine is run- 19. Keep the handles dry, clean and free ning. Use a firm grip with thumb and of oil or fuel mixture. GB-4 01-G3802･3802EZ_GB_306＿三.indd 4 13.6.25 5:26:39 PM... - Page 5 Sudden surprise semble the machine. contributes to accidents. • When you dispose of the machine, fuel, chain oil, be (2) Keep a good grip on the saw with sure to follow your local regulations. both hands, the right hand on the rear GB-5 01-G3802･3802EZ_GB_306＿三.indd 5 13.6.25 5:26:40 PM...
-
Page 6: Explanation Of Symbols On The Machine
If you turn the rod by screwdriver follow the arrow to the "MAX" position, the chain oil flow more, and if you turn to the "MIN" position, less. Position: Bottom of the power unit Shows the directions that the chain brake is released (white arrow) and activated (black arrow). Position: Front of the chain cover GB-6 01-G3802･3802EZ_GB_306＿三.indd 6 13.6.25 5:26:40 PM... -
Page 7: Installing Guide Bar And Saw Chain
Note: Pay attention to the correct direction of the saw chain. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar. Moving direction GB-7 01-G3802･3802EZ_GB_306＿三.indd 7 13.6.25 5:26:40 PM... -
Page 8: Fuel And Chain Oil
• The Zenoah engines are lubricated by oil specially spillage around the unit. formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added WARNING quality oil expressly labeled for air-cooled 2-cycle 1. Select flat and bare ground for fueling. -
Page 9: Operating The Engine
Do not start the engine while the chain saw When adjusting, take the following steps: hangs in one hand. The saw chain may touch your body. This in very dangerous. Note: Be sure to adjust the carburetor with the bar chain attached. GB-9 01-G3802･3802EZ_GB_306＿三.indd 9 13.6.25 5:26:41 PM... - Page 10 ■ STOPPING THE ENGINE 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. Cylinder cover Switch Icing cap GB-10 01-G3802･3802EZ_GB_306＿三.indd 10 13.6.25 5:26:41 PM...
-
Page 11: Sawing
I -2 seconds and pushing the front hand GB-11 01-G3802･3802EZ_GB_306＿三.indd 11 13.6.25 5:26:42 PM... -
Page 12: Maintenance
If any defects are found, make sure to have When installing the main filter, make sure that the grooves them repaired before operating the saw again. on the filter edge are correctly fit with the projections on the cylinder cover. ■ PERIODICAL SERVICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause over- heating of the engine. Periodically check and clean the cylinder fins in the repair specialty store. GB-12 01-G3802･3802EZ_GB_306＿三.indd 12 13.6.25 5:26:43 PM... -
Page 13: Maintenance Of Saw Chain And Guide Bar
Be sure to wear safety gloves. Before filing: • Make sure the saw chain is held securely. • Make sure the engine is stopped. After each cutter has been filed, check the depth gauge • Use a round file of proper size for the chain. and file it to the proper level as illustrated. Chain type: 91PX 95VPX File size: 5/32in (4.0mm) 3/16in (4.8mm) Appropriate gauge checker Make the shoulder round 0.025″ (0.64 mm) Depth gauge standard GB-13 01-G3802･3802EZ_GB_306＿三.indd 13 13.6.25 5:26:43 PM... -
Page 14: Troubleshooting Guide
Top plate cutting angle This saw is equipped with one of the following low kick- back bar/chain combinations: ■ Guide Bar Zenoah Part Number • Reverse the bar occasionally to prevent partial Saw Model Chain Type Guide Bar Saw Chain wear. - Page 15 SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY'S CONTROL. THE PURCHASER SHALL BEAR COSTS OF TRANS- PORTING THE UNIT TO AND FROM THE ZENOAH THIS WARRANTY DOES NOT COVER THOSE PARTS DEALER. REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN THEIR APPEARANCE.
- Page 16 01-G3802･3802EZ_GB_306＿三.indd 16 13.6.25 5:26:44 PM...