Table of Contents
Advertisement
S p e c i f i c a t i o n s
Test Conditions:
Specifications are per channel.
0 dBu corresponds to 0.775 volts RMS regardless of
circuit impedance. This equals 0 dBm into a 600 ohm
circuit for convenient level measurements using meters
calibrated for 600 ohm circuits.
Noise specs based on 20 kHz bandwidth. Noise
increases about 1.7 dB if a meter with a 30 kHz band-
width is used.
FSD = Full Scale Digital, +24 dBu
Microphone Preamplifiers
Source Impedance: 150 ohms
Input Impedance: 2 k ohms min. balanced
Input Level Range: Adj. -65 to -30 dBu
Input Headroom: 20 dB above nom.in.
Analog Inputs
Source Impedance: 600 ohms or less
Input Impedance: >20 k W, balanced
Input Level Range: Adj. -20 to +4 dBu
Input Headroom: 20 dB above nom.
Analog Main Outputs
Output Source Impedance: 100 ohms bal.
Output Load Impedance: 600 ohms min.
Nominal Output Levels:
Program Outputs: adj. +4 dBu
Telco Mix-Minus: set at +4 dBu
Maximum Output Levels:
Program and Monaural: +24 dBu
Telco Mix-Minus: +24 dBu
Digital Inputs & Outputs
Reference: +4 dBu = -20 dB FSD
Signal Format: AES-3, S/PDIF on input only
AES-3 Input Compliance: 24-bit
AES-3 Output Compliance: 24-bit
Digital Reference Frequency: Internal crystal
Internal Sample Rate: 48 kHz
Processing Resolution: 32-bit fixed with ext. precision
accumulators
Conversions: A/D 24-bit Delta-Sigma, Sample rate con-
version on all digital inputs;
D/A 24-bit, using 1-bit conversion.
Latency: <1.3 ms,
Monitor Outputs
Output Impedance: 100 ohms, Z-balanced
Output Load: 600 ohms or greater
Output Level: 4 dBu nominal, +20 dBu max.
External Headphone Amp Output:
Source Impedance: 100 ohms
Load Impedance: >600 ohms
Output Level: +4 dBu nominal, +24 dBu max.
Frequency Response
Mic or Line Input to Program Output:
+0 dB/-0.5 dB, 20 Hz to 20 kHz
Equivalent Input Noise
Microphone Preamp: -127 dBu, 150 ohm source
Dynamic Range
Analog Input to Analog Output: 98 dB "A" weighted
(both ref. to FSD)
Digital Input to Analog Output: 100 dB "A" weighted
(both ref. to FSD)
Total Harmonic Distortion + Noise
Mic Pre Input to Analog Output: <0.015%, 20 Hz to 20
kHz, -38 dBu input, +18 dBu output, 600 ohm load, 20
kHz filter bandwidth.
Analog Input to Analog Output: <0.01% at 1 kHz, +18
dBu input, +18 dBu output, 600 ohm load, 20 kHz filter
bandwidth. <0.05%, 20 Hz to 20 kHz, +18 dBu input, +18
dBu output, 1 k ohm load, 22 kHz filter bandwidth.
Digital Input to Digital Output: <0.001%, 20 Hz to 20 kHz,
+18 dBu input, +18 dBu output, 20 kHz filter bandwidth
Digital Input to Analog Output: <0.005% at 1 kHz, +18
dBu input, +18 dBu output, 600 ohm load, 22 kHz filter
bandwidth. <0.05%, 20 Hz to 20 kHz, +18 dBu input, +18
dBu output, 600 ohm load, 22 kHz filter.
Crosstalk Isolation
Program-to-Program: >86 dB, 20 Hz - 20 kHz
Stereo Separation
Analog Program Outputs: >86 dB @ 1 kHz,
Power Requirements
Input AC voltage: 100-220 VAC, 50/60 Hz
X-mixer-14 current draw: 75 watts
AC Ground: Chassis grounded through AC cord
Arrakis Systems reserves the right to change
specifications without notice or obligation.
4
T H E
X - M I X E R
D I G I T A L
Warranty
The X-mixer console carries a manufacturer's
warranty subject to the following guidelines
and limitations:
A)
Except as expressly excluded here-
in, Arakis ("Seller") warrants equipment of its
own manufacture against faulty workmanship
or the use of defective materials for a period of
one (1) year from date of shipment to Buyer.
The liability of the Seller under this Warranty
is limited to replacing, repairing or issuing
credit (at the Seller's discretion) for any equip-
ment, provided that Seller is promptly notified
in writing within five (5) days upon discovery
of such defects by Buyer, and Seller's examina-
tion of such equipment shall disclose to its sat-
isfaction that such defects existed at the time
shipment was originally made by Seller, and
Buyer returns the defective equipment to Sell-
er's place of business in Loveland, Colorado,
packaging and transportation prepaid, with
return packaging and transport guaranteed.
B)
Equipment furnished by Seller, but
manufactured by another, shall be warranted
only to the extent provided by the other manu-
facturer.
C)
Thermal filament devices (such as
lamps and fuses) are expressly excluded from
this warranty.
D)
The warranty period on equipment
or parts repaired or replaced under warranty
shall expire upon the expiration date of the
original warranty.
E)
This Warranty is void for equip-
ment which has been subject to abuse, improp-
er installation, improper operation, improper
or omitted maintenance, alteration, accident,
negligence (in use, storage, transportation or
handling), operation not in accordance with
Seller's operation and service instructions, or
operation outside of the environmental condi-
tions specified by Seller.
F)
This Warranty is the only warranty
made by Seller, and is in lieu of all other war-
ranties, including merchantability and fitness
for a particular purpose, whether expressed or
implied, except as to title and to the expressed
specifications contained in this manual. Seller's
sole liability for any equipment failure or any
breach of this Warranty is as set forth in sub-
paragraph A) above; Seller shall not be liable
or responsible for any business loss or interrup-
tion, or other consequential damages of any
nature whatsoever, resulting from any equip-
ment failure or breach of this warranty.
C O N S O L E
Advertisement
Table of Contents
