Related Manuals for Regency OASIS
Summary of Contents for Regency OASIS
- Page 1 ’ • • EILING WNER ANUAL •O • ASIS 5/04 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
- Page 2 & O ENERAL NSTALLATION PERATION NSTRUCTIONS MPORTANT AFEGUARDS 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All elec- trical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
-
Page 3: Important Safety Precautions
MPORTANT AFETY RECAUTIONS Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. ARNINGS Disconnect power by removing fuse or turning off circuit breaker before installing the fan. -
Page 4: Unpacking Your Fan
NPACKING Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, the decorative housing may shift, be bent or damaged. -
Page 5: Installing The Mounting Bracket
REPARATION Parts identification on assembled fan Bracket Canopy Downrod Collar Blade Blade Arm Detachable Switch Housing Pull Chain Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. - Page 6 SSEMBLY OF OWNROD YSTEM . 2): TTACHING OWNROD ANOPY AND OLLAR 1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. 3.
- Page 7 NSTALLING 1. Be sure your hanger bracket is secure. The entire weight of the fan will now be hanging from it. 2. Lift fan body/downrod/ball assembly into hanger bracket opening. NOTE: The tab in hanger bracket opening should fit into slot on ball (Fig. 3). 3.
- Page 8 LECTRICAL ONNECTIONS Be sure electricity is turned off at the main power box before wiring LECTRICAL ONNECTIONS 1. Four wires are connected to the fan. Black - this is the “hot” power to run fan. White - this is the “common” power to run fan and light. Blue - this is the “hot”...
-
Page 9: Blade Attachment
LADE TTACHMENT LADE TTACHMENT 1. Place washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this procedure without tightening the screw until all screws have been started into the blade arm. (Fig. 4). 2. -
Page 10: Installation
NSTALLATION EMOVABLE WITCH HOUSING NOTE: Be sure to turn the power off before installing. 1. If installing light kit, attach to switch housing per instructions supplied with light kit. See “Electrical Connections” for hook up of light kit. Carefully remove light kit plug in bottom of switch housing. 2. -
Page 11: Care And Cleaning
& O ENERAL NSTALLATION PERATION NSTRUCTIONS Turn on the power and check operation of the fan. The fan is controlled by the use of the pull chain as follows: one pull = high speed two pulls = medium speed three pulls = low speed four pulls = off For proper functions, ensure that the chain is pulled down fully and released each time. - Page 12 HANK YOU FOR PURCHASING A EGENCY EILING Write to us at: Regency Ceiling Fans P.O. Box 730 Fenton, MO 63026 Visit us on the Web at: www.regencyfan.com 9/02 Regency Ceiling Fans...