Subscribe to Our Youtube Channel
Related Manuals for Goalsetter Systems GS Wall Mount
Summary of Contents for Goalsetter Systems GS Wall Mount
- Page 1 GS WALL MOUNT Junior Wall-Mounted Goal Systems • 36" Junior Wall Mount Installation & Owner’s Instructions Made In The USA...
- Page 2 GOALSETTER ® , GOALSETTER SYSTEMS ® AND GOALSETTER ® logo are all registered trademarks of Goalsetter Systems, Inc. in the U.S. and/or other countries. ™ and BEST IN BASKETBALL ™ are trademarks of Goalsetter Systems, Inc. This product is covered by various U.S. and Canadian patents, including U.S.
-
Page 3: Table Of Contents
Junior Wall Mount Instructions THANK YOU! Thank you and congratulations for purchasing a Goalsetter Goal – the finest basketball goal system on the market today! You will discover that Goalsetter is unsurpassed in product innovation, quality and integrity in the basketball equipment industry. -
Page 4: Safety Instructions
Junior Wall Mount Instructions SAFETY INSTRUCTIONS Failure to follow these safety instructions may result in serious injury or death and/or property damage. • Do not install or use this product unless the instructions within this manual have been carefully read and understood. •... -
Page 5: Goal Assembly
Top Of Frame Height (H) Playing Surface GOAL ASSEMBLY Goalsetter Systems cannot assume liability for the installation of any wall-mounted structure. Goalsetter Systems recommends consulting a professional architect or contractor to determine a safe wall anchoring system to match the wall construction being used in your application. - Page 6 Junior Wall Mount Instructions PARTS LIST & DESCRIPTION – JUNIOR WALL MOUNT Backboard Assembly Frame Hardware Rim & Net 4 places Assembly, Rim Bolt Backplate, & Hardware MINI WALL MOUNT DESCRIPTION Frame Bolt, 3/8"-16 UNC x 1-1/4" Flat Washer, 3/8" Locknut, 3/8"...
-
Page 7: Parts List
Junior Wall Mount Instructions HARDWARE IDENTIFICATION NOTE: Refer to page 6 for descriptions and quantities. Description Parts List Length Callout Mounting Bolt 1-1/4" (at backboad) Rim Bolt Assembly (#5 in Parts List) Black Touch-Up Paint 800.362.GOAL (4625) www.goalsettersystems.com... -
Page 8: Frame Attachment
Junior Wall Mount Instructions FRAME ATTACHMENT Mounting Hole 69-1/8" Up From 16" Playing Surface For 6' Rim Height IMPORTANT: Safe assembly of the Step 5: Level frame horizontally goal requires two or three people in and vertically using a level. Mark good physical condition and wall mounting holes needed for capable of lifting 80-100 lbs (36-45... -
Page 9: Rim Attachment
Junior Wall Mount Instructions RIM ATTACHMENT Step 1: Remove any cardboard edge protectors and protective sheeting from backboard. NOTE: Four steel shouldered bushings 1 are factory installed. If loose, make sure to have them seated properly when tightening rim bolts. If missing, contact Goalsetter or dealer to get replacements. -
Page 10: Frame Assembly
Junior Wall Mount Instructions FRAME ASSEMBLY IMPORTANT: Use two or more Hardware Sequence: Bolt passes through flat washer - mounting plate - frame flange people to raise backboard into - flat washer - locknut. position. They should be in good Step 3: Fully tighten all fasteners. -
Page 11: Cleaning
Junior Wall Mount Instructions CLEANING The exterior finish of your Goalsetter goal is designed for outdoor environments and should only require periodic cleaning and inspection for imperfections that could develop over time (see Maintenance section). When cleaning is necessary, Goalsetter recommends using water and a mild dish detergent applied with a soft, non-abrasive cloth. -
Page 12: Warranties
Goalsetter needs your warranty item returned. Goalsetter will notify you by fax or phone if we determine that the item cannot be claimed under warranty. Goalsetter Systems is not responsible for any charges for labor to install or repair defective product without prior authorization.
Need help?
Do you have a question about the GS Wall Mount and is the answer not in the manual?
Questions and answers