Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
SERVICE MANUAL
GC-QX3HDU/GC-QX5HDU
Regarding service information other than these sections, refer to the GC-QX3U service manual (No.86564).
Also, be sure to note important safety precautions provided in the service manual.
SPECIFICATIONS
Power source
: DC 5 V
Power consumption
: 3.6 W (when the LCD screen is off)
4.8 W (when the LCD screen is on)
Dimensions
: 111 (W) mm x 67 (H) mm x 59 (D) mm
(4-3/8" x 2-11/16" x 2-3/8") (except protruding parts)
Weight
: Approx. 290 g (0.64 lbs)
(without a Memory card and battery)
Operating temperature
: 0°C to 40°C (32°F to 104°F)
Relative humidity
: 35% to 80%
Storage temperature
: –20°C to 50°C (–4°F to 122°F)
LCD screen
: 2.0 inch, polysilicon TFT (200,000 pixels)
Storage media
: SmartMedia
CCD
: 3.34 million pixels (3.24 million valid pixels),
1/1.8" square pixels, primary color filter,
interlace scan CCD
Focal distance
: 7.5 mm to 17.5 mm
(equivalent to 37mm to 86 mm on a 35 mm still camera)
Lens
: 2.3X optical zoom lens
Video
: 160 pixels x 120 pixels, 20 seconds, JVC original format
Recording format
: Exif Ver. 2.1 (DCF compliant), TIFF (Uncompressed),
DPOF-compatible
Sensitivity
: 80/160/320 (ISO compliant)
Iris value (F value)
: F2.8/3.8, 5.6, 8, 11
Exposure control
: Program AE, iris priority AE
: ±2EV (0.5EV steps)
Exposure compensation
Minimum subject distance
: Approx. 2 cm to 50 cm (in Macro mode)
Light measurement system
: Multi, spot
Flash
: Built-in,
Auto/red-eye prevention/forced/disabled
Recommended distance for flash
: Approx. 2.5 m
Shutter speed
: Auto (Program AE: 1/8 seconds – 1/750 seconds,
Iris priority AE: 2 seconds – 1/750 seconds )
White balance
: Auto/Manual ( ,
Focus
: Auto/Manual
DIGITAL STILL CAMERA
TM
3.3V (up to 64MB)
,
, MWB,
)
Self timer
: 1 second, 8 seconds
Photo quality
: 3 modes (STANDARD/FINE/NO COMP.)
Number of storable photos
: 2032 x 1536: approx. 10/8/0
(with an 8MB Memory card,
1024 x 768: approx. 43/32/3
STANDARD/FINE/NO COMP.)
640 x 480: approx. 87/65/8
Battery
: Lithium ion battery
Printer connector
: Output for optional printer
VIDEO output connector
: Two-pole plug, 3.5 mm diameter (NTSC)
Digital output connector
: Mini-USB connector
AC Power Adapter/Charger AA-V37
Power requirement
: AC 120 V`, 60 Hz
U.S.A. and Canada
Other countries
: AC 110 V – 240 V`, 50 Hz/60 Hz
: 14 W
Power consumption
Output
: DC 3.6 V
Charge
Camera
: DC 5.0 V
: 0°C to 40°C (32°F to 104°F)
Operating temperature
[when charging: 10°C to 35°C (50°F to 95°F)]
: 68 (W) mm x 38 (H) mm x 110 (D) mm
Dimensions
(2-11/16" x 1-1/2" x 4-3/8")
: Approx. 230 g (0.51 lbs) (without a DC cord)
Weight
E. & O. E. Design and specifications subject to change without notice.
STILL CAMERA
, 0.77 A
, 1.5 A
No.86588
October 2000
Advertisement
Table of Contents
Related Manuals for JVC GC-QX3HDU
Summary of Contents for JVC GC-QX3HDU
-
Page 1: Specifications
: 14 W Power consumption Lens : 2.3X optical zoom lens Output Video : 160 pixels x 120 pixels, 20 seconds, JVC original format : DC 3.6 V , 0.77 A Charge Recording format : Exif Ver. 2.1 (DCF compliant), TIFF (Uncompressed), Camera : DC 5.0 V... -
Page 2: Table Of Contents
CCD BOARD ASSEMBLY <02> ........4-11 MONI REG BOARD ASSEMBLY <03> ......4-12 JACK BOARD ASSEMBLY <04> ........4-14 STROBE FLASH BOARD ASSEMBLY <05> ....4-15 The following table indicate main different features between models GC-QX3U, GC-QX3HDU and GC-QX5HDU. MODEL GC-QX3U GC-QX3HDU... - Page 3 The following table indicate different parts number between models GC-QX3U, GC-QX3HDU and GC-QX5HDU. PACKING ASSEMBLY <M1> MODEL REF NO. GC-QX5HDU GC-QX3U GC-QX3HDU ITEM PACKING CASE LY31465-002A LY31465-013A LY32048-002A POLY BAG LY30023-016A LY30023-016A CUSHION LY31466-001A LY31466-001A SHEET LY42548-001A –––– –––– HOOD(OP) LY31822-001A ––––...
- Page 4 MAIN BOARD ASSEMBLY <01> MODEL REF NO. GC-QX5HDU GC-QX3U GC-QX3HDU ITEM MAIN BOARD ASSEMBLY YB10282B-06 YB10299K-03 YB10299U-01 CCD BOARD ASSEMBLY <02> MODEL REF NO. GC-QX5HDU GC-QX3U GC-QX3HDU ITEM CCD BOARD ASSEMBLY YB10283A1-04 YB10300K1-02 YB10300U1-01 MONI REG BOARD ASSEMBLY <03> MODEL REF NO.
-
Page 5: Important Safety Precautions
Important Safety Precautions Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. - Page 6 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compli- ance with safety standards.
-
Page 8: Disassembly
SECTION 1 DISASSEMBLY NOTE : This service manual has indicated only the item different from GC-QX3U No.86564. 1.3.2 Disassembly method ( I ) NOTE STEP PART NAME FIG. NO. POINT FRONT CASE Remove screws REAR CASE 2 (115), 3 (156), 4 (157), 1 (154) 1-3-1 OPERATION UNIT Remove the Connector... - Page 9 Note 5 Pass this through the inside of the boss. MONI/REG BOARD ASSY < 02 > (SD1) MAIN BOARD ASSY < 01 > CCD BOARD ASSY < 03 > (SD3) (SD4) (SD5) JACK BOARD ASSY OP BLOCK ASSY < 04 > <M3>...
-
Page 10: Electrical Adjustment
However, if both or either of the following parts is replaced, it needs special adjustment with a personal computer at a JVC service equipment after the part replacement • OP block assembly Cleaning cloth •... -
Page 11: Setup (Ccd Adjustment)
2.1.5 Setup (CCD ADJUSTMENT) Setup for electrical adjustment with personal computer Note 1: As a general rule for adjustment with a personal computer, connect a personal computer to its DIGITAL terminal. Note 2: Use DC cord to supply the power. Service support system YTU94057-49 Jig connector cable... -
Page 12: Setup With Patch Cords And Jig Connector Cables
Setup with patch cords and jig connector cables Note: Fig. 2-2-1 shows an example of expansion setup that facilitates inspection of major boards because main components are connected by means of patch cords and jir cables.For proceeding to electrical adjustment in such the setup, disassemble the set at certain level required for the current adjustment objectives referring to the section 1 "DISASSEMBLY"... - Page 14 JVC SERVICE & ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP. Head office (973)315-5000 1700 Valley Road Wayne, New Jersey 07470-9976 (973)396-1000 East Coast 10 New Maple Avenue Pine Brook, New Jersey 07058-9641 705 Enterprise Street Aurora, Illinois 60504-8149...
-
Page 15: Charts And Diagrams
SECTION 3 CHARTS AND DIAGRAMS NOTES OF SCHEMATIC DIAGRAM 4. Voltage measurement 1) Video circuits Safety precautions Voltage are DC-measured (reference to ground) with a volt- The Components identified by the symbol meter by suppling the color bar signal during print screen critical for safety. -
Page 16: Circuit Board Notes
6. Signal path Symbols CIRCUIT BOARD NOTES The arrows indicate the signal path as follows. 1. Foil and Component sides 1) Foil side (B side) : Memory screen main signal path Parts on the foil side seen from foil face (pattern face) Memory screen and E-E signal path are indicated. -
Page 17: Board Interconnection
BOARD INTERCONNECTION NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. P.S. CN3003 CN5501 CN101 CN502 CN501 SSFDC REG_3.0V 3.0V MAIN REG_3.0V D/A_YCOUT CN1001 CN2001... -
Page 18: Main (Syscon) Schematic Diagram
MAIN (SYSCON) SCHEMATIC DIAGRAM NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. 0 1 MAIN (SYSCON) DSP97 AUDIO SCK_0 SO_0 CDS AGC A/D SDWE SI_0 SDCLK... -
Page 19: Main (Dsp146) Schematic Diagram
MAIN (DSP146) SCHEMATIC DIAGRAM NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. 0 1 MAIN (DSP146) C3043 L3003 10µ /6.3 NQR0129-002X L3001 NQR0129-002X C3045... -
Page 20: Main (Dsp97) Schematic Diagram
MAIN (DSP97) SCHEMATIC DIAGRAM NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. DSP146 JACK SYSCON DSP146 SYSCON 0 1 MAIN (DSP97) IC5003 TC7SHU04FU-X R5159... - Page 21 MAIN (CDS AGC A/D AND ARM ROM) SCHEMATIC DIAGRAM MAIN (STROBE CONTROL AND AUDIO) AND STROBE FLASH SCHEMATIC DIAGRAM NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. MAIN (CDS AGC A/D) CN2002 AL_3.3V...
-
Page 22: Main (Cds Agc A/D And Arm Rom)
MAIN (F/Z_MDA / IRIS) SCHEMATIC DIAGRAM JACK (VIDEO OUT/USB/PRINTER/DC JACK/MONITOR BACK LIGHT) SCHEMATIC DIAGRAM NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. JACK (VIDEO OUT/USB/PRINTER/DC JACK/MONITOR BACK LIGHT) R135 0Ω... -
Page 23: Ccd Schematic Diagram
CCD SCHEMATIC DIAGRAM NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. REG_15.0V D1001 1SS355-X L1002 NQL045K-100X L1001 C1022 10µ NQR0129-002X REG_-7.5V C1004 L1004 L1003... -
Page 24: Moni Reg (Monitor) Schematic Diagram
3.10 MONI REG (MONITOR) SCHEMATIC DIAGRAMS NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. MONI REG (MONITOR) REG_15.0V REG_3.0V R7206 0Ω R7202 IC7202 C7205... -
Page 25: Monitor Reg (Dc/Dc) Schematic Diagram
3.11 MONITOR REG (DC/DC) SCHEMATIC DIAGRAMS NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. MONI REG (DC/DC) R9018 0Ω Q9007 L9002 OPEN OPEN F9001... - Page 26 NOTE : Since there is no interchangeable of MAIN PWB and JACK PWB, be careful. 3.12 MAIN CIRCUIT BOARD PWB No. interchangeable table PWB No. PWB No. interchangeable 01 MAIN YB10299-01-01 YB10299-01-03 03 MONI/REG YB10300-01-01 YB10300-01-02 04 JACK YB10300-01-01 YB10300-01-02 02 CCD YB10300-01-01 YB10300-01-02...
- Page 27 COMPONENT PARTS LOCATION GUIDE <MAIN > YB10299-01-01 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. C3026 B C 1C C5505 A C 1B L5505 A C 1A DIODE CAPACITOR C3027 B C 2B C5506 A C 1B L5506 B C 2A C402...
- Page 28 COMPONENT PARTS LOCATION GUIDE <MAIN > YB10299-01-01 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CATION R3014 B C 1B R4004 B C 1B R4099 A C 3A R5529 B C 2A RESISTOR R3015 A C 2A R4005 B C 2B...
- Page 29 NOTE : Since there is no interchangeable of MAIN PWB and JACK PWB, be careful. MAIN CIRCUIT BOARD PWB No. interchangeable table PWB No. PWB No. interchangeable 01 MAIN YB10299-01-01 YB10299-01-03 03 MONI/REG YB10300-01-01 YB10300-01-02 04 JACK YB10300-01-01 YB10300-01-02 02 CCD YB10300-01-01 YB10300-01-02 05 STROBE...
- Page 30 NOTE : Since there is no interchangeable of MAIN PWB and JACK PWB, be careful. 3.13 MAIN CIRCUIT BOARD PWB No. interchangeable table PWB No. PWB No. interchangeable 01 MAIN YB10299-01-01 YB10299-01-03 03 MONI/REG YB10300-01-01 YB10300-01-02 04 JACK YB10300-01-01 YB10300-01-02 02 CCD YB10300-01-01 YB10300-01-02...
- Page 31 COMPONENT PARTS LOCATION GUIDE <MAIN > YB10299-01-03 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. L5005 B C 2A C3024 B C 2B CN5501 A C 5B C5023 B C 2A CAPACITOR L5501 A C 1B C3025 B C 2B CN6601 A C 3A C5501...
- Page 32 COMPONENT PARTS LOCATION GUIDE <MAIN > YB10299-01-03 REF.NO. LOCATION REF.NO. LOCATION CATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION R3014 B C 1B R4005 B C 2B R4100 A C 3A R5531 B C 1B RESISTOR R3015 A C 2A R4006 B C 2B...
- Page 33 NOTE : Since there is no interchangeable of MAIN PWB and JACK PWB, be careful. MAIN CIRCUIT BOARD PWB No. interchangeable table PWB No. PWB No. interchangeable 01 MAIN YB10299-01-01 YB10299-01-03 03 MONI/REG YB10300-01-01 YB10300-01-02 04 JACK YB10300-01-01 YB10300-01-02 02 CCD YB10300-01-01 YB10300-01-02 05 STROBE...
-
Page 34: Monitor Reg Circuit Board (Yb10300-01-01)
3.14 MONITOR REG CIRCUIT BOARD ATTENTION: CAUTION: POUR UNE PROTECTION PERMANENTE FOR CONTINUED PROTECTION AGAINST CONTRE LES RISQUE D’INCENDE, FIRE HAZARD, REPLACE ONLY WITH SAME REMPLACER LE FUSIBLE PAR UN AUTRE TYPE AND RATED FUSE. DE MEME TYPE ET DE MEME TENSION. COMPONENT SIDE (A) FOIL SIDE (B) ZP9001... - Page 35 3.15 MONITOR REG CIRCUIT BOARD ATTENTION: CAUTION: POUR UNE PROTECTION PERMANENTE FOR CONTINUED PROTECTION AGAINST CONTRE LES RISQUE D’INCENDE, FIRE HAZARD, REPLACE ONLY WITH SAME REMPLACER LE FUSIBLE PAR UN AUTRE TYPE AND RATED FUSE. DE MEME TYPE ET DE MEME TENSION. COMPONENT SIDE (A) FOIL SIDE (B) D9306...
-
Page 36: Jack Circuit Board (Yb10300-01-01)
NOTE : Since there is no interchangeable of MAIN PWB and JACK PWB, be careful. 3.16 JACK CIRCUIT BOARD PWB No. interchangeable table ATTENTION: CAUTION: PWB No. PWB No. interchangeable POUR UNE PROTECTION PERMANENTE FOR CONTINUED PROTECTION AGAINST CONTRE LES RISQUE D’INCENDE, 01 MAIN YB10299-01-01 YB10299-01-03... - Page 37 NOTE : Since there is no interchangeable of MAIN PWB and JACK PWB, be careful. 3.17 JACK CIRCUIT BOARD PWB No. interchangeable table ATTENTION: CAUTION: PWB No. PWB No. interchangeable POUR UNE PROTECTION PERMANENTE FOR CONTINUED PROTECTION AGAINST CONTRE LES RISQUE D’INCENDE, 01 MAIN YB10299-01-01 YB10299-01-03...
-
Page 38: Ccd Circuit Board (Yb10300-01-01)
3.18 CCD CIRCUIT BOARD 3.19 CCD CIRCUIT BOARD FOIL SIDE (B) FOIL SIDE (B) TL-GND5 TL-GND5 TP1005 TP1005 TP1006 TP1006 C1006 L1003 L1003 C1006 L1006 L1006 C1005 C1003 C1003 C1005 C1004 C1004 R1012 R1012 L1008 L1008 L1009 L1009 C1028 C1028 C1011 C1011 C1027... - Page 39 3.20 STROBE FLASH CIRCUIT BOARD 3.21 STROBE FLASH CIRCUIT BOARD FOIL SIDE (B) FOIL SIDE (B) ZP1-1 ZP1-1 R6511 R6511 R6528 IC6502 R6528 IC6502 R6529 Q6502 R6529 R6514 R6504 Q6502 R6514 R6506 R6504 R6506 C6503 C6503 D6504 D6504 R6509 R6527 D6502 Q6503 R6527...
-
Page 40: Over All Block Diagram
3.22 OVER ALL BLOCK DIAGRAM CN502 FSL_R+ IC1001 FSL_R- ICX252AQ STROB_AD REER STROB_AD ACTOR GATE_PULSE P008 STO_CHG P006 IC1002 JCY0146 IC2001 IC501 SD_0, SCLK_0 (CDS AGC A/D) IC502 CLK36 CLK36 IC1004 FORCUS CN3001 64M SDRAM DATA0-15 /ZOOM IC3501 A0-11 F_OUT ZOOM IC3503 MOTOR... -
Page 41: Parts List
AC POWER ADAPTER MA BT-51020-2 REGIST.CARD AA-V37U FINAL ASSY M2 LY31583-002A BATTERY PACK (refer to MANUAL No.86564) LY31583-002C AC POWER ADAPTER GC-QX3HDU/QX5HDU LY20867-001A FILM COPY ADAP., GC-X5HDU LY32047-001A FILMHOLDER ASSY, GC-X5HDU LY32050-001A CUSHION(ACC), GC-X5HDU QQR0491-002 CORE FILTER QQR0491-001 CORE FILTER,x2... -
Page 42: Final Assembly M2
< > FINAL ASSEMBLY 153C 153B 153D 153A STROBE 101B BOARD ASSY < 05 > 101E MONI/REG BOARD ASSY < 02 > 101D 101C 153E 101E 101A MAIN BOARD ASSY 101G < 01 > 101F OP BLOCK UNIT 107B <M3> JACK BOARD ASSY 152A <... - Page 43 LY41860-001A TERMINAL(BATTERY) 101D LY41861-001A SPRING(BATTERY) 101E LY30018-019A SPECIAL SCREW 101F QUB221-14A3A8 WIRE,BRN 101G QUB222-05A3A8 WIRE,RED LY31457-002A PWB HOLDER ASSEMBLY, GC-QX3HDU LY31457-007B PWB HOLDER ASSEMBLY, GC-QX5HDU LY31467-001A HOLDER(LCD) LY30029-031A SPACER(A) LY30016-085A SPACER-A ––– LCD MODULE ASSEMBLY 107A QLD0131-001 LCD MODULE 107B...
-
Page 44: Electrical Parts List
ELECTRICAL PARTS LIST REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... - Page 45 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 46 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 47 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 48 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
-
Page 49: Ccd Board Assembly <02
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 50: Moni Reg Board Assembly <03
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... - Page 51 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
-
Page 52: Jack Board Assembly <04
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 53: Strobe Flash Board Assembly <05
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
Need help?
Do you have a question about the GC-QX3HDU and is the answer not in the manual?
Questions and answers