Drain Pan; Freeze Protection; Furnace Suspension; Lternate Lectrical And As Ine Onnections - Goodman GKS9 Installation Instructions Manual

AIR
DISCHARGE
Side
Return
Duct
Connection
ALTERNATE FLUE
PIPE LOCATIONS
AIR
DISCHARGE
UPFLOW HORIZONTAL
LEFT AIR DISCHARGE
Bottom
Return
Duct
Connection
UPFLOW HORIZONTAL
RIGHT AIR DISCHARGE
Recommended Installation Positions
NOTE: Alternate "vertical" piping connections can not be used when
an upflow furnace is installed with supply air discharging to the right.
In either case, use the standard flue and combustion air piping
connections.
A E
LTERNATE LECTRICAL AND
This furnace has provisions allowing for electrical and gas line con-
nections through either side panel. In horizontal applications the
connections can be made either through the "top" or "bottom" of the
furnace.
D P
RAIN AN
A drain pan must be provided if the furnace is installed above a
conditioned area. The drain pan must cover the entire area under
the furnace (and air conditioning coil if applicable).
F P
REEZE ROTECTION
Refer to Section VII, Horizontal Applications and Conditions - Drain
Trap and Lines.
F S
URNACE USPENSION
If the furnace is installed in a crawl space it must be suspended
from the floor joist or supported by a concrete pad. Never install the
furnace on the ground or allow it to be exposed to water. Refer to
Section IV, Location Requirements and Considerations - Furnace
Suspension for further details.
VIII. PRO O O O O P P P P P ANE GA VIII. PR VIII. PR ANE GA ANE GAS /HI ANE GA S /HIGH AL S /HI S /HI
VIII. PR VIII. PR ANE GA S /HI
P
OSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH MAY OCCUR IF
THE CORRECT CONVERSION KITS ARE NOT INSTALLED.
MUST BE APPLIED TO INSURE SAFE AND PROPER FURNACE OPERATION.
CONVERSIONS MUST BE PERFORMED BY A QUALIFIED INSTALLER OR SERVICE
AGENCY.
This furnace is shipped from the factory configured for natural gas
at standard altitude. Propane gas installations require an orifice
ALTERNATE FLUE
PIPE LOCATIONS
Side
Return
Duct
Connection
Bottom
Return
Duct
Connection
UPFLOW
UPRIGHT
Bottom
Return
Duct
Connection
AIR
DISCHARGE
G L C
AS INE ONNECTIONS
GH AL GH AL GH ALTITUD TITUD TITUD TITUDE INST E INSTALL E INST E INST ALL ALLA A A A A TI ALL
GH AL TITUD E INST ALL
WARNING
T
HE APPROPRIATE KITS
change to compensate for the energy content difference between
natural and propane gas.
High altitude installations may require both a pressure switch and
an orifice change. These changes are necessary to compensate
for the natural reduction in the density of both the gas fuel and the
combustion air at higher altitude.
For installations above 7000 feet, please refer to your distributor for
required kit(s).
Altitude
Natural
0-7000
Propane
NOTE: In Canada, gas furnaces are certified to 4500 feet.
Contact the distributor for a tabular listing of appropriate
manufacturer's kits for propane gas and/or high altitude installations.
The indicated kits must be used to insure safe and proper furnace
operation. All conversions must be performed by a qualified installer,
or service agency.
IX. VENT/FL IX. VENT/FL
IX. VENT/FLUE PIPE & CO IX. VENT/FL IX. VENT/FL
G

ENERAL

F
AILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN BODILY INJURY OR
C
DEATH. AREFULLY READ AND FOLLOW ALL INSTRUCTIONS GIVEN IN THIS
SECTION.
U
PON COMPLETION OF THE FURNACE INSTALLATION, CAREFULLY INSPECT THE
ENTIRE FLUE SYSTEM BOTH INSIDE AND OUTSIDE THE FURNACE TO ASSURE IT
IS PROPERLY SEALED.
PERSONAL INJURY OR DEATH DUE TO EXPOSURE TO FLUE PRODUCTS,
INCLUDING CARBON MONOXIDE.
A condensing gas furnace achieves its high level of efficiency by
extracting almost all of the heat from the products of combustion
and cooling them to the point where condensation takes place. Be-
cause of the relatively low flue gas temperature and water conden-
sation requirements, PVC pipe is used as venting material.
This furnace must not be connected to Type B, BW, or L vent or vent
connector, and must not be vented into any portion of a factory built
or masonry chimney except when used as a pathway for PVC as
described later in this section. Never common vent this appliance
with another appliance or use a vent which is used by a solid fuel
appliance. Do not use commercially available "no hub connectors"
other than those shipped with this product.
TI TI TIO O O O O NS NS NS NS
TI NS
It is the responsibility of the installer to follow the manufacturers'
recommendations and to verify that all vent/flue piping and connec-
tors are compatible with furnace flue products. Additionally, it is the
responsibility of the installer to ensure that all piping and connec-
tions possess adequate structural integrity and support to prevent
flue pipe separation, shifting, or sagging during furnace operation.
A
LL
D C
UAL ERTIFICATION
This furnace is dual certified and may be installed as a non-direct
vent (single pipe) or direct vent (dual pipe) appliance. A non-direct
vent installation requires only a vent/flue pipe, while a direct vent
12
HIGH ALTITUDE GAS ORIFICE CHART
Gas Kit Orifice
None #43
LPT-00A #55
UE PIPE & CO UE PIPE & CO MBUSTIO O O O O N AIR PIPE MBUSTI MBUSTI
UE PIPE & CO UE PIPE & COMBUSTI MBUSTI
WARNING
WARNING
L
EAKS IN THE FLUE SYSTEM CAN RESULT IN SERIOUS
: N -D /D
ON IRECT IRECT
Manifold Pressure
Pressure Switch
3.5" w.c.
None
10.0" w.c.
N AIR PIPE N AIR PIPE
N AIR PIPE N AIR PIPE
V
ENT