This document is to be used with the Baracoda USB Plug and Scan Dongle
Package Contents
Baracoda, Inc. (US Offi ce)
45 Main street - Suite 616 - Brooklyn, NY 11201
Ph: 718 488 9600 - Fx: 718 488 9601
The bluetooth name and Bluetooth registered trademarks are owned by Bluetooth SIG, Inc., and are used by Baracoda under license. The Baracoda names and
How to connect your BaracodaPencil ................7 How to connect your BC2604/BL2604/BLR2604 ..............7 How to connect your BCM2604-L/BCM2604-F ..............8 How to connect your RoadRunners and BaracodaPencil2 ..........9 How to disconnect your USB Plug & Scan Dongle ..............10 Additional features ........................11 Prefix..........................11 Suffix..........................12 Only for BC2604/BL2604/BLR2604 products ..............13...
(this is the ‘No data loss mode’) Simply plug the USB Plug & Scan dongle in your computer, scan a “connect barcode” with a Baracoda scanner, and the Bluetooth connection will be automatically established.
2.2 CAPS LOCK function The USB Plug & Scan dongle can unactivate the CAPS LOCK key on the HOST. Force Caps lock OFF : enabled < : ? > ' \ N U L \ S O H \ S O H Force Caps lock OFF : disabled <...
USB Plug & Scan Dongle - User Guide 2.3 No data loss mode The ‘No data loss mode’ is activated by default for all scanners supporting the feature (2604, RoadRunners (Decoder version 3.10 or newer) and BaracodaPencil2. When you leave the connection zone, the ‘No data loss mode’...
Indeed, the USB Plug&Scan dongle emulates a Keyboard. Thus, it has to send characters with a minor delay between them. If the delay is too short or if the host is too slow or too busy to process the incoming characters, some data can be lost by the host.
2. Plug the dongle into the USB port of the computer. 3. Wait 5 seconds for the host computer to recognize the USB Plug & Scan dongle. It is possible that the host computer will not recognize the dongle: this can be corrected by going to the control panel hardware wizard and searching for a USB HID device.
3. Plug the dongle into the USB port of the computer. 4. Wait 5 seconds for the host computer to recognize the USB Plug & Scan dongle. It is possible that the host computer will not recognize the dongle: this can be corrected by going to the control panel hardware wizard and searching for a USB HID device.
2. Plug the dongle into the USB port of the computer. 3. Wait 5 seconds for the host computer to recognize the USB Plug & Scan dongle. It is possible that the host computer will not recognize the dongle: this can be corrected by going to the control panel hardware wizard and searching for a USB HID device.
4 How to disconnect your USB Plug & Scan Dongle There are 3 different ways to disconnect a scanner from the USB Plug & Scan dongle. 1. Reading the disconnect barcode with the connected barcode. Use this barcode to disconnect your barcode scanner from a USB Plug and Scan dongle.
USB Plug & Scan Dongle - User Guide 5.3 Only for BC2604/BL2604/BLR2604 products The Number of Beeps for ‘good scan’ Warning: These settings are only possible with BC/BL-2604 scanners. After scanning the desired barcode, disconnect the scanner (reading the “disconnect barcode”), wait for ten seconds and connect again using the “connect barcode.”...
Page 14
USB Plug & Scan Dongle - User Guide The Number of Beeps for ‘ACK’(in ‘no data loss mode’) Warning: These settings are only possible with BC/BL-2604 scanners. After scanning the desired barcode, disconnect the scanner (reading the “disconnect barcode”), wait for ten seconds and connect again using the “connect barcode.”...
HUNGARY ITALY (by default) PORTUGUAL 6.2 Scanner configurations Please note that the USB Plug & Scan forces the settings of the scanner to which it gets connected in the following configuration: • Restore scan engine defaults • Enable default code ID •...
This barcode will display the firmware version: Print firmware version 7 Compatibility The USB Plug & Scan is only compatible with the following Baracoda barcode readers: • RoadRunners (BRR-L and BRR-F) : All versions (‘No data loss mode’ configurable from decoder v3.10 & Radio v1.72) •...