Related Manuals for Baracoda BLUETOOTH RS232RS232
Summary of Contents for Baracoda BLUETOOTH RS232RS232
-
Page 1: User Guide
RS232 RS232 dongle Plug & Scan dongle Plug & Scan User Guide ©Baracoda – April 2009 Data Capture for Workforce in Motion... -
Page 2: Table Of Contents
... 8 OW TO USE WITH UNNERS 2 & R OW TO USE WITH ENCIL UNNERS HOW TO CONNECT YOUR BARACODA BARCODE SCANNER ... 10 OW TO CONNECT YOUR ARACODA ENCIL BC2604/BL2604/BLR2604... 10 OW TO CONNECT YOUR BCM2604-L/BCM2604-F... 11 OW TO CONNECT YOUR ... -
Page 3: Revision History
Data Capture for Workforce in Motion... -
Page 4: Introduction
Data Capture for Workforce in Motion... -
Page 5: Technical Introduction
Data Capture for Workforce in Motion Block diagram... - Page 6 Data Capture for Workforce in Motion...
-
Page 7: N O Data Loss Mode
Data Capture for Workforce in Motion by default Your scanner and any future connected scanners will retain this configuration Enable ‘no data loss mode’ (*) Disable ‘no data loss mode’ Note... -
Page 8: Batch Mode
Enable batch mode Upload batch data (only for RoadRunners) Enable batch mode Upload batch data (only for Pencil2, RoadRunners Evolution, DualRunners) Data Capture for Workforce in Motion... - Page 9 (for Pencil2 & RoadRunners Evolution) Disable upload messages (*) (for Pencil2 & RoadRunners Evolution) <UPL>: start xxxxx <UPL>: transmission OK <UPL>: transmission NOK Enable upload messages Data Capture for Workforce in Motion...
-
Page 10: How To Connect Your Baracoda Barcode Scanner
(*) If the LED on the BaracodaPencil is not double flashing green, this may possibly mean: The BaracodaPencil is low on power. Charge the unit up completely and try again The BaracodaPencil has not been reset. Reset it and try again The BaracodaPencil has been programmed from its default status and it is not able to decode the Code 128 symbology. -
Page 11: How To Connect Your Bcm2604-L/Bcm2604-F
(*) If the LED on the BL/BC/BLR2604 is not double flashing a green light, this may possibly mean: The scanner is low on power. Charge the unit up completely and try again The scanner has not been reset. Reset it and try again The scanner has been programmed from its default status and it is not able to decode the Code 128 symbology. -
Page 12: How To Connect Your Road Runners /Road Runners Evolution
Data Capture for Workforce in Motion... -
Page 13: How To Connect Your Dual Runners
Data Capture for Workforce in Motion... -
Page 14: How To Disconnect Your Plug & Scan Dongle
Data Capture for Workforce in Motion barcode Disconnect... -
Page 15: Additional Features
Disable prefix [default] SOH prefix STX prefix Horizontal Tab (HT) prefix Disable suffix [default] EOT suffix ETX suffix Horizontal Tab (HT) suffix Carriage Return (CR) suffix Line Feed (LF) suffix Carriage Return (CR) Carriage Return (CR) + Line Feed (LF) suffix Data Capture for Workforce in Motion... - Page 16 9600 bps [default] 38400 bps 115200 bps 1 stop bit [default] None [default] Even 9600 / 8 / 1 / None Data Capture for Workforce in Motion 19200 bps 57600 bps 2 stop bits...
- Page 17 The Number of Beeps for ‘good scan’ The Number of Beeps for ‘good scan’ 0 beep [default] 1 beep 2 beeps 3 beeps Data Capture for Workforce in Motion DISCONNECT...
- Page 18 The Number of Beeps for ‘ACK’(in ‘no data loss mode’) The Number of Beeps for ‘ACK’(in ‘no data loss mode’) 0 beep 1 beep [default] 2 beeps 3 beeps Data Capture for Workforce in Motion DISCONNECT...
-
Page 19: Print Firmware Version
Data Capture for Workforce in Motion Print firmware version... -
Page 20: Compatibility
Data Capture for Workforce in Motion... -
Page 21: Limited Warranty
Data Capture for Workforce in Motion...