Subscribe to Our Youtube Channel
Related Manuals for Miranda M848-9005-470
Summary of Contents for Miranda M848-9005-470
- Page 1 Intuition XG Advanced HD/SD graphics co-processor Installation & Quick Start Guide M848-9005-470 w w w . m i r a n d a . c o m...
- Page 3 Intuition XG-e Vertigo Suite v4.7 Intuition XG-3U-e Intuition XG-Dual-e Advanced HD/SD Graphics Processors Installation & Quick Start Guide...
- Page 4 Miranda Technologies Inc. reserves the right to revise and improve its products at any time and without notice. This publication describes the state of this product at the time of its publication, and may not reflect the product at all times in the future.
-
Page 5: Safety Compliance
Safety Compliance This equipment complies with the requirements of the following standards for Safety of Information Technology Equipment: • CSA C22.2 no. 60950-1-07 (2 Edition) • UL 60950-1 (2 Edition) • IEC/EN 60950-1 (2 Edition) Warning: An appropriately listed/certified main supply power cord must be used for the connection of the equipment to the main voltage at either 120V or 240V CAUTION:... - Page 6 WARNING Vertigo XG devices contain Class 1 lasers, which are deemed safe under normal operating conditions. Standalone Equipment - Laser source(s) employed: CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1...
-
Page 7: Table Of Contents
ABLE OF ONTENTS Introduction .......................... 1-1 Intuition XG product description ......................1-2 Overview of the Intuition XG-e chassis....................1-6 Front panel components (Intuition XG-e)..................1-7 Rear panel components (Intuition XG-e) ..................1-7 Overview of the Intuition XG-3U/Dual chassis................... 1-8 Front panel components (Intuition XG-3U/Dual)................1-9 Rear panel components (Intuition XG-3U/Dual) ................. - Page 8 Table of Contents TOC-2 Intuition XG Installation & Quick Start Guide...
-
Page 9: Introduction
New Intuition XG devices are factory configured for standard rendering and playout workflows. Configuring the Intuition XG settings for advanced workflows is normally performed by qualified network administrators or Miranda’s Integration Specialists using the Intuition XG Portal and Dashboard software interfaces. Information and instructions for... -
Page 10: Intuition Xg Product Description
Introduction Intuition XG product description The Intuition XG graphics co-processor significantly extends the graphics and clip playout capabilities of master control switcher systems, like the Imagestore 750 or NV51000MC, by feeding the HD/SD fill/key inputs. It’s ideal for playout of the most advanced data-driven, channel branding and promotional graphics, including: “Coming up next”... - Page 11 Introduction Intuition-XG-3U-e A single channel graphics co-processor, generally used upstream of a master control switcher like the Imagestore 750 or NV5100MC. Fill Video In A Out A • 3RU chassis with redundant power supply unit. • 1 HD/SD video input, 1 HD/SD (Fill & Key) output •...
- Page 12 Introduction Intuition-XG-Dual-e A dual channel graphics co-processor, generally used upstream of a master control switcher like the Imagestore 750 or NV5100MC. Fill Out A Video In A Fill Video In B Out B • 3RU chassis with redundant power supply unit. •...
- Page 13 Introduction The following options are available on Intuition XG devices: VX-ClipPlayer Clip Player The Clip Player is an internal codec package for playing out multi-format video clips. VX-Audio-e Audio Processing The discrete audio I/O card allows the Intuition XG to capture, process and output discrete audio.
-
Page 14: Overview Of The Intuition Xg-E Chassis
Introduction Overview of the Intuition XG-e chassis The Intuition XG-e is a single HD/SD channel playout server (1 HD/SD video input, 1 HD- SDI Fill + Key output) that incorporates the Intuition XG graphics engine to rendering advanced graphics. Physically, the Intuition XG is a 1RU rackmount playout server with a single power supply unit and 1 TB of storage. - Page 15 Introduction Intuition XG-e) Front panel components ( The Intuition XG’s front panel provides convenient access to the SATA hard drives, two USB ports, a CD/DVD ROM drive, two fans, and a control panel containing five LEDs and two buttons for system monitoring and operation. Figure identifies the LEDs, buttons and connectors on the front panel of the Intuition XG-e.
-
Page 16: Overview Of The Intuition Xg-3U/Dual Chassis
Introduction Overview of the Intuition XG-3U/Dual chassis The Intuition XG unit is a 3RU rackmount rendering platform that incorporates redundant fans, three power supplies, and 1 TB RAID1-enabled storage (optional 2 TB RAID10 expansion). The only visible difference between the 3RU models of the Intuition XG is that the single channel model (XG-3U-e) has only one (1) discrete AES audio connector, while the dual channel model (XG-Dual-e) has two (2) discrete AES audio connectors. -
Page 17: Front Panel Components (Intuition Xg-3U/Dual)
Introduction Intuition XG-3U/Dual) Front panel components ( The Intuition XG’s front panel provides convenient access to the hard drives, two USB ports, a CD/DVD ROM drive, and a control panel containing six LEDs and three buttons for system monitoring and operation. Figure identifies each component on the Intuition XG’s front panel. - Page 18 Introduction Intuition XG-3U/Dual) Rear panel components ( The Intuition XG’s rear panel provides convenient access to the video card’s I/O connector, which provides 4 SD/HD SDI video outputs, a reference signal input, and AES audio input/output. The rear panel also provides access to the graphics card connector, as well as various I/O ports (RS-422, USB, Ethernet...etc.).
-
Page 19: Installation Instructions For The Intuition Xg-E
NSTALLATION INSTRUCTIONS FOR THE NTUITION This chapter identifies and describes the tasks for performing a first-time installation of a factory-configured Intuition XG-e device. CA UTION Intuition XG devices should only be installed by trained personnel in a restricted access locations only. All health and safety regulations and precautions must be observed. Step # Task description Unpack the parts included in the shipping package... -
Page 20: Unpacking And Verifying The Intuition Xg-E Shipped Items
Intuition XG-e. O T E If any damage occurred during transportation or if any items are missing from the package, please contact Miranda’s Customer Service and Sales department. - Page 21 Vertigo Suite software and the user documentation. A sticker on the DVD identifies the release version of the Vertigo Suite software. Please consult http://support.miranda.com for the latest software and documentation updates. Intuition XG Configuration Guide A printed copy of the Intuition XG Configuration Guide, which provides practical reference and procedural information on how to use the Intuition XG’s desktop and remote configuration...
- Page 22 • Miranda Technical Support Contacts and Warranty card This card contains warranty information related to the Intuition XG hardware and software. It also identifies Miranda’s contact information, which is also provided on page 5-1. • License Agreement card (Miranda Technologies Inc.) This card describes the terms of Miranda’s license...
-
Page 23: Mounting The Intuition Xg-E Chassis In A Rack
Installation instructions for the Intuition XG-e Mounting the Intuition XG-e chassis in a rack Included in the shipping package is a Rack mounting kit, which contains the rails, screws and washers required to mount the Intuition XG-e (1RU) chassis into an equipment rack. Note that the rails are designed to fit in racks with a depth of 28”... - Page 24 Installation instructions for the Intuition XG-e Repeat steps 2 to 4 for the other inner rail extension. Each outer rail is in two sections that must be assembled before mounting onto the rack. Identify the left and right outer rails by examining the ends which bend outward. Slide the front section of the outer rail into the rear section of the outer rail.
- Page 25 Installation instructions for the Intuition XG-e CA UTION Due to the heavy weight of the Intuition XG device, ensure that the rack is securely anchored onto a unmovable surface or structure before installing the chassis into the rack. Install the chassis into a rack. Confirm that chassis includes the inner rails and rail extensions.
-
Page 26: Cabling The Intuition Xg-E Unit
Installation instructions for the Intuition XG-e Cabling the Intuition XG-e unit Once the Intuition XG-e chassis is securely mounted in an equipment rack, you can connect the required cables to the rear connectors. Figure and the cabling procedure provide step- by-step instructions for properly cabling the Intuition XG-e unit. - Page 27 Installation instructions for the Intuition XG-e SDI OUT D /K Not used on an Intuition XG-e unit. ANALOG REF IN Connect to a house reference (Analog Blackburst or HD Tri-Level) to synchronize the phase timing video and graphics processing. ANALOG REF Optional connection.
- Page 28 Installation instructions for the Intuition XG-e 2-10 Intuition XG Installation & Quick Start Guide...
-
Page 29: Installation Instructions For The Intuition Xg-3U/Dual
NSTALLATION INSTRUCTIONS FOR THE XG-3U/D NTUITION This chapter provides you with instructions for performing a first-time installation of a factory-configured Intuition XG-3U-e or Intuition XG-Dual-e devices. CA UTION Intuition XG devices should only be installed by trained personnel in a restricted access locations only. -
Page 30: Unpacking And Verifying The Intuition Xg-3U/Dual's Shipped Items
Intuition XG. O T E If any damage occurred during transportation or if any items are missing from the package, please contact Miranda’s Customer Service and Sales department. - Page 31 Installation instructions for the Intuition XG-3U/Dual Discrete (AES) audio breakout cable Single channel Intuition XG units (XG-3U-e) have one discrete (AES) audio connector, while dual channel Intuition XG units (XG- Dual-e) have two discrete (AES) audio connectors. For each physical SDI video output, there will be a discrete audio breakout cable.
- Page 32 • Miranda Technical Support Contacts and Warranty card This card contains warranty information related to the Intuition XG hardware and software. It also identifies Miranda’s contact information, which is also provided on page 5-1. • License Agreement card (Miranda Technologies Inc.) This card describes the terms of Miranda’s license...
- Page 33 Installation instructions for the Intuition XG-3U/Dual ATI FirePro kit The ATI FirePro kit items are not required during the installation of a factory configured Intuition XG. The Intuition XG uses the ATI FirePro graphics card. As such, the following ATI FirePro’s installation items are also included in the Intuition XG shipping package: •...
-
Page 34: Mounting The Intuition Xg-3U/Dual Chassis In A Rack
Installation instructions for the Intuition XG-3U/Dual Mounting the Intuition XG-3U/Dual chassis in a rack Included in the shipping package is a Rack mounting kit, which contains the rails, screws and washers required to mount the Intuition XG chassis into an equipment rack. Note that the rails are designed to fit in racks with a depth of 28”... - Page 35 Installation instructions for the Intuition XG-3U/Dual Locate the five rail buttons on each side of the chassis and locate the five corresponding holes on each of the inner rails. (*Please note that one end of the hole is larger than the other end of the hole.) Align the larger end of each hole against its corresponding button.
- Page 36 Installation instructions for the Intuition XG-3U/Dual After you have installed the inner rails on the chassis, you are ready to install the outer rails of the rail assemblies to the rack. In the package, locate a pair of front (-short) and rear (-long) brackets. Please note that the brackets are marked with Up/Front arrows (-front) and Up/Rear arrows (-rear).
- Page 37 Installation instructions for the Intuition XG-3U/Dual 13. Slide the Intuition XG chassis into the rack as shown below. The chassis may not slide into the rack smoothly or easily when installed for the first time. Adjustments to the slide assemblies might be necessary to achieve a smooth insertion.
-
Page 38: Cabling The Intuition Xg-3U/Dual Unit
Installation instructions for the Intuition XG-3U/Dual Cabling the Intuition XG-3U/Dual unit Once the Intuition XG chassis is securely mounted in an equipment rack, you can connect the required cables to the rear connectors of the Intuition XG unit. Figure and the cabling procedure provide step-by-step instructions for properly cabling the Intuition XG unit. - Page 39 Installation instructions for the Intuition XG-3U/Dual To cable the Intuition XG-3U-e or the Intuition XG-Dual-e: Connect the three (3) AC power cables to the power supply sockets on the rear panel of the Intuition XG chassis. WA RNING DO NOT plug the power cables into AC power sockets yet. Connect the Keyboard and Mouse to the USB connectors on the front or rear...
- Page 40 Installation instructions for the Intuition XG-3U/Dual SDI OUT B Second output channel connection for dual channel Intuition XG units (XG-Dual-e). For the purposes of this setup procedure, connect this cable to a broadcast monitor. Not used on single channel Intuition XG units (X-3U-e). SDI OUT C /K The matching key signal for SDI OUT A.
- Page 41 Installation instructions for the Intuition XG-3U/Dual Optional: Connect a Time Code Generator to the Time Code card’s BNC connector on the rear panel of the Intuition XG. The Time Code Card is a hardware option on the Intuition XG (see page 1-5), which allows you to lock the Intuition XG’s system clock to an external timecode.
- Page 42 Installation instructions for the Intuition XG-3U/Dual 3-14 Intuition XG Installation & Quick Start Guide...
-
Page 43: Quick Start Instructions
UICK START INSTRUCTIONS This chapter provides you with instructions for performing the initial setup tasks to get the a newly installed Intuition XG device up and running. The procedure concludes by verifying the installation by previewing the playout of an asset in Intuition XG’s Live Window and a broadcast monitor. -
Page 44: Starting The Intuition Xg
Quick start instructions Starting the Intuition XG Once the Intuition XG is properly racked and cabled, you can make the power connections and you can perform the first-time start up of the Intuition XG unit. Plug the monitor’s power cable into a power socket and power it on. Plug the Intuition XG’s power supply cable(s) into a power socket. - Page 45 Quick start instructions Xplay Xplay is the playout control application that the master control system or device uses to control the playout of video and graphics on the Intuition XG device. Whether the Intuition XG is a single or dual channel model, only one instance of Xplay is used to control the Intuition XG device’s output.
-
Page 46: Assigning A New Ip Address To The Intuition Xg Device
Quick start instructions Assigning a new IP address to the Intuition XG device Factory configured Intuition XG units are shipped with a dynamic IP address. Using DHCP is not recommend, so you must assign a new static IP Address to the Intuition XG device. To change the Intuition XG’s current dynamic IP address to a static IP address: In the Vertigo Command Shell, type ipconfig and take note of the current IP configuration. -
Page 47: Verifying The Installation And Setup By Previewing The Playout
Quick start instructions Verifying the installation and setup by previewing the playout To verify that the Intuition XG is properly connected and operating, we recommend that you use the local copy of Xplay to load and playout an asset in the Live window and broadcast monitor associated with the Intuition XG’s Channel A. - Page 48 Quick start instructions Enable the Intuition XG’s Live window For installation and troubleshooting purposes, the Intuition XG is equipped with a preview window called the Live Window. The Live Window allows you to display a representation of the output channel’s playout directly on the Intuition XG’s desktop. To enable the device channel’s Live Window: If Channel A’s Dashboard is not already open, select the T >L...
- Page 49 Quick start instructions Use Xplay to playout a graphic To verify that the Intuition XG is properly connected and playing out, the following procedures has you add a template asset to the playlist, then cue and take the asset so that it plays out in the Live window, as well as the broadcast monitor.
-
Page 50: Completing The Quick Start Procedure
Quick start instructions Completing the quick start procedure With the Intuition XG now capable of playing out graphics, we recommend that you disable the Live Windows as they put an unnecessary burden on the system’s resources during on-air playout. Since the mouse, keyboard and DVI monitor are only used during the setup and configuration procedures, you can also disconnect these peripherals from the Intuition XG unit. -
Page 51: Need Further Assistance
EED FURTHER ASSISTANCE Technical Support For technical assistance, please contact the Miranda Technical support centre nearest you: Americas Telephone: +1-800-224-7882 e-mail: support@miranda.com Asia Telephone: +81-3-5644-7663 e-mail: asiatech@miranda.com Europe, Middle East, Africa, UK Telephone: +44 (0) 1491 820222 e-mail: eurotech@miranda.com France (only) Telephone: +33 (0) 1 55 86 87 88 e-mail: francetech@miranda.com... - Page 52 Need further assistance? Miranda’s Corporate headquarters You can also contact Miranda’s corporate headquarters at: Miranda Technologies Inc. 3499 Douglas-B.-Floreani St-Laurent, Quebec, Canada H4S 2C6 Tel. 514-333-1772 Fax. 514-333-9828 www.miranda.com Intuition XG Installation & Quick Start Guide...
Need help?
Do you have a question about the M848-9005-470 and is the answer not in the manual?
Questions and answers