Table of Contents
Advertisement
Timer Recording
Up to 8 timer recording programs can be made using VCR Plus+
timer programing, Express timer programing or 24HR Quick
Programing method as far as a year in advance. Remember, the
clock must be set before you can program the timer.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
NOTES:
If all the 8 programs have already been set, "PROGRAM FULL"
appears on the TV screen.
After timer recording is completed, the VCR turns off
automatically.
You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
To timer-record cable or satellite channels, perform "Cable Box
and/or DBS Receiver Control Setting" (
keep the cable box or DBS receiver turned on.
Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time, channel settings, and other
menu settings are lost. As a result, when the power is supplied
again to this VCR after the power failure, this VCR starts the
Plug&Play setting automatically to restore the clock time and
channel setting. If the clock time and channel setting are
restored correctly, each timer program you have made will start
at its start time unless its end time has elapsed.
If the tape reaches its end during timer recording, the recording
stops and "
", " " and " $" on the display panel blink. Press
#
TIMER to disengage timer, then press STOP/EJECT (0) on
the VCR to eject the cassette or press POWER 1 then press
REW (3) on the Remote to rewind the tape.
Changing VCR Plus+
The VCR Plus+ programing system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the VCR Plus+ "Guide Channel Set" for each
station.
If you have moved to a different area or if a broadcasting station's
channel number has been changed, perform the following steps to
set the correct guide channel number.
A
Access Main Menu screen, then Initial Set screen
Press MENU on the Remote. Press
(arrow) to "INITIAL SET", then press OK or
B
Access Guide Channel Set screen
Press
to move the highlight bar (arrow) to "GUIDE
rt
CHANNEL SET", then press OK or
C
Input guide channel number
Press
or the Number keys to select the
rt
VCR Plus+ guide channel number as
shown in the TV listing, then press OK or
.
e
D
Input receiving channel number
Press
or the Number keys to select the
rt
number of the channel on which the guide
channel's broadcasts are received, then
press OK or
.
e
3
4
Repeat steps
and
for each instance.
E
Return to normal screen
Press MENU on the Remote.
pg. 7) and be sure to
Setting
®
to move the highlight bar
rt
.
e
.
e
GUIDE CHANNEL SET
GUIDE CH :
VCR CH
: – – –
PRESS NUMBER KEY (0–9)
OR ( , ), THEN (OK)
PRESS (MENU) TO END
GUIDE CHANNEL SET
GUIDE CH :
VCR CH
: 47
PRESS NUMBER KEY (0–9)
OR ( , ), THEN (OK)
PRESS (MENU) TO END
VCR Plus+
The PlusCode programing numbers are
the numbers next to the program in
most TV listing.
Load a cassette with the record safety
tab intact. The VCR turns on, and the
counter is reset, automatically.
A
Press PROG. on the Remote to access
the PlusCode No. screen.
PLUSCODE NO.
PRESS NUMBER KEY (0–9)
PRESS (+/–) TO SET
EXPRESS PROGRAMMING
PRESS (PROG.) TO END
B
Press the appropriate Number keys
to input the PlusCode number, then
press OK or
the setting is accurate on the Program screen.
PLUSCODE NO.
1 2 3 4 5 6 7 8
PRESS NUMBER KEY (0–9)
PRESS (PROG.) TO END
If the Guide Channel Set screen
appears after pressing OK, press the
Number keys, CH+/– or
the number of the channel on which
the broadcast for the PlusCode
number is received on the VCR or
cable box, then press OK.
To set the tape speed, press SP/EP.
To change the stop time, press STOP+/–.
To timer-record daily (Monday–Friday) or weekly serials,
press DAILY (M-F) (Number key "8") or WEEKLY (Number
key "9"). Pressing the button again makes the "DAILY" or
"WEEKLY" display disappear.
If you made a mistake, press CANCEL to access the PlusCode
No. screen again.
If an incorrect PlusCode number or the one for a broadcast
already finished has been inputted, "ERROR" is displayed for
about 5 seconds, then the PlusCode No. screen reappears.
C
Press OK or PROG..
If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, see "Program overlap warning display" (
D
Press TIMER. The VCR turns off automatically and "
displayed on the display panel.
6
6
— 12 —
Timer Programing
®
. Check to make sure
e
PROGRAM 1
(PLUSCODE NO. 12345678)
START
8:00PM
DATE
12/24/03
WED
PRESS (8=DAILY, 9=WEEKLY
THEN (OK)
STOP+/– = STOP TIME, SP/EP)
PRESS (PROG.) TO END
to input
rt
CONTINUED ON NEXT PAGE
STOP
10:00PM
CH
12 SP
GUIDE CHANNEL SET
GUIDE CH : 12
VCR CH
: – – –
PRESS NUMBER KEY (0–9)
OR ( , ), THEN (OK)
PRESS (PROG.) TO END
pg. 14).
" is
#
Hide quick links:
Advertisement
Table of Contents
