Timer Recording; System Setup - JVC HR-J781AM Instructions Manual

Timer Recording

Up to 8 timer recording programs can be made using G-
S V timer programing or Express timer programing method
HOW IEW
as far as a year in advance. Remember, the clock must be set
before you can program the timer.
NOTES:
If all the 8 programs have already been set, "PROGRAM FULL"
appears on the TV screen.
After timer recording is completed, the recorder turns off
automatically.
You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is
not exhausted).
™
G- /S
CODE HOW
INFORMATION
G- and S V are different trademarks used to represent
CODE HOW IEW
the same easy recording feature, but only the term G-
will be used in the instructions. If you use the S
follow the same instructions listed for the G-
The G- timer programming system eliminates the need to
CODE
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
You have to set "GUIDE PROG" numbers, which are assigned to
each station for purposes of G-
the stations stored in your recorder's memory to get proper results.
Before G- setup you must have performed the procedures of
CODE
Tuner Set and Clock Set.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.
Guide Program Number Set
A
Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press
pointer next to "INITIAL SET", then press OK or
B
Access G- /S V
CODE HOW IEW
Press to place the pointer next to "G-CODE/SHOWVIEW
rt
SETUP", then press OK or
e
C
Input Guide Prog number
Press or the Number keys to select
rt
the Guide Program number as shown in
the TV listing, then press OK or
D
Input receiving channel number
Press or the Number keys to select
rt
the number of the channel on which the
Guide Program number's broadcasts are
received, then press OK or
e
If the satellite broadcast is received on
your recorder's auxiliary channel ("L-1"
or "F-1"), select "L-1" or "F-1" for the channel position to which
the satellite receiver is connected.
3 3 3 3 4 4 4 4
Repeat steps and as necessary.
E
Return to normal screen
Press MENU on the remote control.
CODE
™
V

System Setup

IEW
CODE
V
HOW IEW
system.
CODE
number for the
CODE
timer programming, for all
CODE
to place the
rt
.
e
Setup screen
.
G-CODE/SHOWVIEW SETUP
GUIDE PROG
2
.
e
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-CODE/SHOWVIEW SETUP
GUIDE PROG
2
.
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-
CODE
Programing
/
The G-
CODE
next to the program in most TV listing.
Remember, the clock must be set
before you can program the timer.
Be sure to read "G-
S V
HOW IEW
Load a cassette with the record safety
tab intact. The recorder turns on, and
the counter is reset, automatically.
Select the appropriate colour system
with "PAL/MESECAM" and "NTSC"
in Function settings.
A
Press PROG on the remote control
to access the G-
screen.
G-CODE/SHOWVIEW NO.
system
system,
[0 – 9]
[+/–] : EXPRESS PROGRAMING
[PROG] : EXIT
B
Press the appropriate Number keys to input the G-
number, then press OK. Check to make sure the setting is
accurate on the G-
G-CODE/SHOWVIEW NO.
1 2 3 4 5 6 7 8
[0 – 9]
[ ] : DELETE
[PROG] : EXIT
If the G-
screen appears after pressing OK,
press the Number keys, PR+/– or
to input the number of the
rt
channel on which the broadcast for
the G-
the recorder, then press OK.
To set the tape speed, press SP/LP/EP.
To change the stop time, press STOP+/–.
To timer-record daily (Monday–Friday) or weekly serials,
press DAILY or WEEKLY. Pressing the button again makes the
"DAILY" or "WEEKLY" display disappear.
If you made a mistake, press & to access the G-
S V
HOW
If an incorrect G-
broadcast already finished has been inputted, "ERROR" is
displayed for about 5 seconds, then the G-
screen reappears.
C
Press OK or PROG.
If "PROGRAM OVERLAPPED" appears, see "Program
overlap warning display".
TV PROG
5
D
Press . The recorder turns off automatically and "
#
displayed on the display panel.
NOTE:
If the tape reaches its end during timer recording, the recording
stops and "
#
TV PROG
5
™ ™
/S V
HOW IEW
numbers are the numbers
™
/
CODE
™
System Setup".
/S V
CODE HOW IEW
Program screen.
CODE
NO. 12345678
START
21:00
DATE
25.04
: [OK]
/S V Setup
CODE HOW IEW
number is received on
CODE
screen again.
IEW
/S V number or the one for a
CODE HOW IEW
" , " " and " " on the front display panel blink.
e
Timer
CODE
– P1 –
STOP
22:00
SP
TV PROG
1
G-CODE/SHOWVIEW SETUP
GUIDE PROG TV PROG
2 5
[0–9] OR [ / ] : SELECT
[PROG] : EXIT
/
CODE
/S V
CODE HOW IEW
" is
#