Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Proxxon MICRO-Router MOF
Summary of Contents for Proxxon MICRO-Router MOF
- Page 1 ProxxonTools.com MICRO-Router Manual...
- Page 2 Notes...
- Page 3 Fig. 2 Fig. 1 Fig. 3 Fig. 4 Fig. 5...
- Page 4 Fig. 6 Fig. 7a Fig. 7b Fig. 8a Fig. 8b...
- Page 5 Fig. 10 Fig. 9 Fig. 11 Fig. 12 Fig. 13...
-
Page 6: Table Of Contents
Accessories ............16 Accessories recommended and actually provided by PROXXON ... . . 16 Explosion drawing . -
Page 7: General Safety Instructions
(one blade is wider than the other.) This plug will fit PROXXON does not accept responsibility for in a polarized outlet only one way. If the safe functioning of the machine the plug does not fit fully in the outlet, •... -
Page 8: Specific Safety Rules
diately. Damaged cords increase the 17. Do not use tool if switch does not risk of electric shock. turn it on or off. Any tool that cannot be 8. When operating a power tool outside, controlled with the switch is dangerous use an outdoor extension cord and must be repaired. - Page 9 use this tool unsafely or incorrectly, you can 19. vibration or wobbling that could indicate suffer serious personal injury. improperly installed bit. 1. Hold on the power tool by insulated gripping surfaces when performing an SAVE THESE INSTRUCTIONS! operations where the cutting tool may contact hidden wiring or its own cord.
-
Page 10: Symbols
4. Wear a dust mask if applicable. 13. Parallel limit stop 5. Use only accessories and spare parts 14. Circular limit stop recommended by PROXXON (comply 15. Guide bars with max. permissible speeds). 16. Open-end wrench 6. Always use dust extraction (use only 17. -
Page 11: Scope Of Delivery
1 pc. suction hose You can acquire a variety of high-grade pro- 1 pc. parallel limit stop file mills for wood and similar materials from 1 pc. circular limit stop Proxxon. 2 pc. each guide bars... -
Page 12: Insertion And Replacement Of The Mill Cutter Router Bit (Fig. 2)
These mill cutters (with a shank diameter of 7.2.2 Replacing the mill cutter router 1/8” or 3.2 mm) are attuned to the use of bit (Fig. 2): your machine and guarantee excellent re- sults. WARNING! Please make sure the plug has been pulled out when replacing the mill cutter! 7.2 Insertion and replacement of the In all cases, ensure the router bit used is... -
Page 13: Milling Depth Adjustment (Fig. 5)
1, the desired height change can be When working with the vacuum cleaner, it is made exact by turning it back and forth. recommended you to use the PROXXON AS/E suction controller device. 1. Clamp in the desired cutter (see chapter 7.2., „Insertion and replacement of the... -
Page 14: Milling With Limit Stops
• For practical purposes, one should use 1. As in illustration 8a, push both guide bars one limit stop for each type of milling (2) into bores 3 in limit stop 1 using the work. There are different possibilities for pin, and firmly tighten both headless this, so only the most practical are ex- screws (4) with the aid of a hollow hexa-... -
Page 15: On-The-Fly" Submersion (Fig. 11)
Repair service is available at your PROXXON service center (You will find the address at the back of this manual). 7.6 „On-the-fly“ submersion (fig. 11) -
Page 16: Accessories
Replace damaged or worn router bits immediately. They represent a safety risk and worsen the work result. Please use PROXXON accessories. NOTE: The use of improper accessories may cause hazards. 9.1 Accessories recommended and actually provided by PROXXON (Current and available at the time this manual was printed): Wood Router Bits Made from high speed steel, with 1/8"...
Need help?
Do you have a question about the MICRO-Router MOF and is the answer not in the manual?
Questions and answers