Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stageline LSX-650SRGB
Summary of Contents for Stageline LSX-650SRGB
- Page 1 This manual contains important laser system safety and operation information. Read and understand all instructions prior to powering on laser unit the first time, to avoid laser eye injury and to avoid breaking the law. Keep this manual in a safe place for future reference.
- Page 2 USER MANUAL WARNING DATA Lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety REMARK and WARNING statement in the user manual. Read all instructions carefully BEFORE operating this device.
-
Page 3: Laser Safety Warnings
USER MANUAL LASER SAFETY WARNINGS Potential laser injury hazard exists with this product! Read these Instructions carefully, which include important information about installation, safe use and service! Caution Avoid direct eye contact with laser 了 light. Never intentionally expose your eyes or others to direct laser radiation. - Page 4 USER MANUAL LASER SAFETY AND OPERATING INSTRUCTIONS STOP AND READ ALL LASER SAFETY DATA Laser light is different from any other light source witch you may be familiar. The light from this product can potentially cause eyes injury if not set up and used properly.
-
Page 5: Laser Exposure Warning
USER MANUAL After set up, and prior to public use test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of higher laser levels. -
Page 6: Laser Safety Label Reproductions
USER MANUAL LASER SAFETY LABEL REPRODUCTIONS This is only one laser aperture on this product. The label Indicates laser beam output aperture Caution – Class 4 LASER RADIATION, WHEN OPEN, AVOID EXPOSURE BEAM LASER EMISSION DATA Laser Classification Class 4 Green Laser Medium DPSS Nd:YVO4,532nm Red Laser Medium... -
Page 7: Laser Compliance Statement
USER MANUAL Note: The laser diode is exposed to extreme conditions due to the high output power and therefore only has a limited life. Like all wear parts, the laser diode is not subject to any guarantee claims. LASER COMPLIANCE STATEMENT This laser product complies with EN/IEC 60825-1 Ed 2,2007-03. - Page 8 USER MANUAL Always disconnect from the mains, when the devise is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. It is essential to connect the yellow/green conductor to earth. The electric connection, repairs and servicing must be carried out by a qualified employee.
-
Page 9: Before Operation
USER MANUAL BEFORE OPERATION Unpacking Instructions CAUTION! Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. -
Page 10: Dmx-512 Connection Between Fixtures
USER MANUAL channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the source voltage matches the fixture’s requirement. The unit is supplied with a power plug appropriate to its voltage and destination. - Page 11 USER MANUAL Building a serial DMX-chain If you are using the standard DMX-controllers, you can connect the DMX-output of the controller directly with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter cables.
- Page 12 USER MANUAL Proper Laser Set Up & Usage This fixture has been designed to be hung. It is recommended for safety purposes, your lighting effect are properly mounted using a suitable hanging clamp and safety cable. Items appropriate for safe and effective mounting are easily sourced from your lighting vendor.
-
Page 13: Rigging The Fixture
USER MANUAL Rigging the Fixture CAUTION! Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealers! The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.. -
Page 14: Product Overview
USER MANUAL PRODUCT OVERVIEW This device has left out premise in absolutely perfect condition. In order to maintain this condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device. -
Page 15: Rear Panel
USER MANUAL Rear Panel NAME FUNCTION Switch Switch on and off the power With socket and integrated fuse holder Mains input Music, ILDA, Patterns Setting ILDA / Hardware Setting Switch off the laser manually if error occurs Urgent and safe switch Key switch SD MMC storage RAM (less than 2G) Safety eye... - Page 16 USER MANUAL ILDA / Hardware Setting Panel NAME FUNCTION Turn the knob to adjust the audio respond MUISC sensitivity. X SIZE The Size of X axis adjustment The Size of Y axis adjustment Y SIZE ILDA THROUGH Standard ILDA DB25 Output(through) Standard ILDA DB25 Input ILDA INPUT ILDA connection indicator LED.
-
Page 17: Control & Function
USER MANUAL IMPORTANT For your own safely and full laser safety Regulation, we do strongly recommend You to take this optional switch! CONTROL & FUNCTION Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use. Do not switch the unit on and off in short time intervals Always unplug the unit when it is not used for a longer time. - Page 18 USER MANUAL Mode Option, to choose the operating mode of laser. Confirmation, to confirm the laser to show the present mode at the next operation. UP/DOWN, to change operating mode, parameter or DMX address. OPERATION AUTO SHOW 1 Press FUNC to enter MODE OPTION Till to AUTO SHOW 1 shown on LCD monitor.
- Page 19 USER MANUAL AUTO SHOW 2 Press FUNC to enter MODE OPTION Till to AUTO SHOW 2 shown on LCD monitor. The laser is set at AUTO SHOW 2 standalone mode and it will play the preprogrammed show until next setting is changed. AUTO SHOW 2 is slow and soft show which is better for MUSIC BAR.
- Page 20 USER MANUAL Attention In preprogrammed standalone MUSIC SHOW mode, the laser beam will be blank-out in 3 seconds without AUDIO/MIC activated signal. DMX MODE Press FUNC to enter MODE OPTION Till to DMX address shown on LCD monitor. Press UP/DOWN to change the DMX address that you wanted.
-
Page 21: Dmx Channels Chart
USER MANUAL Attention The X/Y scanned world mirror setting could be done by both LCD control panel and ILDA setting panel. ILDA Control Mode This unit has the ILDA DB25 port, and it can be controlled by the PC, There is auto transform set in the inside of the unit to transform the ILDA and preprogrammed show. - Page 22 USER MANUAL DMX MINI PREPROGRAM SHOW MODE CHANNEL VALUE DESCRIPTION CH 2 000-255 46 Mini preprogram laser shows SHOWS DMX PATTERN MODE CHANNEL VALUE DESCRIPTION CH 2 000-255 Every 16 for 1 group, total 8 groups. GROUP 000-255 Every 16 for 1 pattern, total 16 patterns. CH 3 PATTERN 000-007 Original...
- Page 23 USER MANUAL CLIPING 001-127 0%~99% fixed pattern clipped 128-255 slow to fast pattern clipping 000-127 100%-5% fixed pattern zoomed 128-169 Slow to fast pattern zooming OUT CH 6 ZOOMING 170-209 Slow to fast pattern zooming IN 210-255 Zooming IN and then zooming OUT CH 7 000-255 Slow to fast...
- Page 24 USER MANUAL MOVING 192-255 Anticlockwise moving CH 17 0-255 Slow to fast MOVESPEED Attention To shut off the second pattern, set CH1 at 192-223, set CH2 at 000-032 and set CH3 at 000-005. SPECIFICTAIONS Mains Input: AC100~240V, 50/60Hz Fuse: 250V /1.6A Slow Blow (20mm Glass) Total Power: X/Y Axis Beam Angle: ±20°...
Need help?
Do you have a question about the LSX-650SRGB and is the answer not in the manual?
Questions and answers