1. Manuals
  2. Brands
  3. Mopar Manuals
  4. Car Video System
  5. DVD REAR SEAT VIDEO SYSTEM
  6. Installation instructions manual

Mopar DVD REAR SEAT VIDEO SYSTEM Installation Instructions Manual

For jeep grand cherokee
Hide thumbs Also See for DVD REAR SEAT VIDEO SYSTEM:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Vehicles equipped with REC Navigation Radio will require an upgrade so that the vehicle speakers will
function when a DVD is playing.

TOOLS REQUIRED:

• Scissors
• Sharp utility knife
• 10mm Socket
• Socket wrench
• T50 Torx bit
• Tape Measure
• Diagnostic STAR SCAN tool
CONTENTS:
2 A
3 A
5 A
K6859241
• New roll of masking tape
• T15, T20, T25 Torx drivers
• Torque wrench
4 A
2 B
13
9
4 B
11
14
6
15
10
8
12
16
DVD REAR SEAT VIDEO SYSTEM

INSTALLATION INSTRUCTIONS

• Non-metal trim stick
• Magnetized T15 torx driver
• Metal wire routing tool
Item
1
1
2 A
3 A
4 A
5 A
Vehicles without sunroof:
3 B
2 B
3 B
4 B
6
7
8
9
10
11
12
13
14
15
16
17
18
18
19
11/09/2004
JEEP GRAND CHEROKEE
• Hooked Pick Tool
• Strong adhesive tape
Qty. Description
1
4
M6 U-Nuts
1
3
4
4
M6 U-Nuts
1
Mounting Bracket
4
M6 Screws & Washers
1
6
Tie Straps
1
1
DVD Player Bracket
1
4
3
4
1
1
DVD Remote
1
Mercury Warning Label
6
Batteries
2
Headphones
1
Operating Instructions
17
7
Page 1 of 10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DVD REAR SEAT VIDEO SYSTEM and is the answer not in the manual?

Questions and answers

Related Manuals for Mopar DVD REAR SEAT VIDEO SYSTEM

Summary of Contents for Mopar DVD REAR SEAT VIDEO SYSTEM

  • Page 1: Table Of Contents

    DVD REAR SEAT VIDEO SYSTEM JEEP GRAND CHEROKEE INSTALLATION INSTRUCTIONS Vehicles equipped with REC Navigation Radio will require an upgrade so that the vehicle speakers will function when a DVD is playing. TOOLS REQUIRED: • Scissors • Sharp utility knife •...

  • Page 2: Template

    A – Trim Out the Headliner: Headliner Grab Handles 1) Trim out supplied template (Item 1) along the doted lines as indicated for vehicles with or without sunroof. 2) Position and tape template to the headliner where indicated. 3) Measure 20" (508mm) from the rear of overhead console to the front of template.

  • Page 3: Vehicles With Sunroof

    7) Disconnect and remove left and right headliner grab handles (two T20 screws). 8) Remote left and right C-pillar trim panels Left Headliner Grab Handle 9) Remove center console radio bezel. Center Console Radio Bezel 10) Remove the radio (four phillips screws). 11) Remove and discard back cover from the rear of floor console.

  • Page 4: Mounting Bracket

    C1 – Install Screen Console Mounting Bracket on Vehicles with Sunroof: NOTE: See next page for install on vehicles without sunroof. 1) Install two u-nuts (Item 2A) on each side of the left and right sunroof inner frame. To Front of U-Nuts (2) Vehicle Each Side...
  • Page 5 C2 – Install Screen Console Mounting Bracket on Vehicles U-Nuts (2) without Sunroof: 1) Install four u-nuts (Item 2B) to slots in the front and rear roof crossbow as shown. 2) Carefully slide the screen console mounting bracket (Item 3B) forward from rear opening of headliner.

  • Page 6: Overhead Harness

    D – Install Overhead Harness and Power Harness: Overhead Harness 1) Carefully lower the headliner and let it rest on the front and rear seat headrests. 2) Starting at the left (driver’s side) rear door, route black connector on overhead harness (Item 6) under headliner and out of trimmed opening.

  • Page 7: Power Harness

    10) Hand feed 12-way connector on power harness Power (Item 8) into radio opening and down the right side Harness of center console. 11) Plug 22-way connectors in-between the radio and radio harness connector. 12) Plug 10-way connector into the radio. NOTE: If there is a 10-way connector already present in the radio, it means that the vehicle is Radio...

  • Page 8: Dvd Player

    13) Route power harness and overhead harness rearward behind right side of floor console and under the carpet liner. 14) Position the harness connectors approximately Floor 6" (152mm) out of the rear console’s end cap Console mounting tabs. 15) Bundle up any slack in the harness, tape, and tuck neatly inside of center console.

  • Page 9: Screen Console

    3) Plug 12-way power harness connector and 16-way overhead harness connector into the back of DVD Overhead player. Harness 4) Fully engage the DVD bracket’s two hook tabs to the floor console bottom mounting slots. Power 5) Snap four retaining clips on the DVD bracket into Harness the floor console mounting slots.
  • Page 10 5) Turn on ignition and the unit will power up. 6) Use a diagnostic STARSCAN tool so that the Front Control Module (FCM) is reconfigured and recognizes the Video Entertainment System (VES). Follow the procedure shown below. IN THE INITIAL START UP SCREEN •...

Table of Contents