Operating Jvc's Audio/Video Components - JVC RX-668VBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 24) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source.
To operate a source with the remote control, the source must be
selected using buttons on the remote control.
• Refer also to the manuals supplied with your components.
CATV/SAT
DELAY
1
EFFECT
4
MENU
7/P
100+
+10
VOLUME
SLEEP ONE TOUCH
OPERATION
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM:
Alternates between FM and AM.
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
32
POWER
TV VCR AUDIO
CATV SOUND
CD-DISC
CONTROL CONTROL
TEST SURROUND
2 3
– CENTER +
5 6
– REAR•L +
8 9
– REAR•R +
RETURN
0 10
ENTER
SET
CH TV VOL. OSD
EXIT
TV/VIDEO
CD
VCR
RM-SR668U
REMOTE CONTROL
Sound control section (Amplifier)
After pressing SOUND CONTROL, you can perform the following
operations:
SURROUND: Selects the DSP modes.
CENTER – / +: Adjusts the center speaker output level for the
Surround/DVD MULTI playback modes.
REAR•L – / +: Adjusts the left/right rear speaker output level for
the DSP modes.
Adjusts the left rear speaker output level for the
DVD MULTI playback mode.
REAR•R – / +: Adjusts the right rear speaker output level for the
DVD MULTI playback mode.
DELAY:
Selects the delay time of the rear speaker sound.
(Only works when "PRO LOGIC" is selected.)
EFFECT: Selects the effect level for the DSP modes.
TEST:
Turns on or off the test tone output for the
Surround mode.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using 10 keys;
otherwise, 10 keys cannot be used for operating your target source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
3:
Starts playing.
4 4
4 4 4 :
Returns to the beginning of the current (or
previous) track.
¢ ¢ ¢ ¢ : ¢
Skips to the beginning of the next track.
7:
Stops playing.
8: Pauses playing. To release it, press 3.
1 – 10, +10:
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD player-changer
After pressing CD-DISC, you can perform the following operations
on a CD player-changer:
3:
Starts playing.
4 4 4 : 4 4
Returns to the beginning of the current (or previous)
track.
¢ ¢ ¢ ¢ : ¢
Skips to the beginning of the next track.
7:
Stops playing.
8: Pauses playing. To release it, press 3.
1 – 6, 7/P: Select the number of a disc installed in a CD player-
changer.
After pressing CD, you can perform the following operations on the
CD player-changer:
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.