Peg-Perego PRIMO VIAGGIO SIP 30-30 Owner's Manual
Peg-Perego PRIMO VIAGGIO SIP 30-30 Owner's Manual

Peg-Perego PRIMO VIAGGIO SIP 30-30 Owner's Manual

Side impact protection
Hide thumbs Also See for PRIMO VIAGGIO SIP 30-30:

Advertisement

PRIMO VIAGGIO SIP 30•30
Side Impact Protection
WARNING:
Do not install or use this infant restraint
until you read and understand all
instructions in this manual. To avoid
serious injuries to your baby, follow
the instructions carefully and be sure
to buckle your baby using the 5-point
harness.
PrimoViaggioSIP-US_30-30_FIUS0901 1
O W N E R ' S
M A N U A L
Child Requirements:
Weight limits: 30 pounds (13,5 kg)
Maximum height: 30 inches (76 cm)
FIUS0902I61
USA
Istructions for use EN
(IMMI)
26-10-2009 10:50:11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRIMO VIAGGIO SIP 30-30 and is the answer not in the manual?

Questions and answers

Summary of Contents for Peg-Perego PRIMO VIAGGIO SIP 30-30

  • Page 1 Istructions for use EN (IMMI) PRIMO VIAGGIO SIP 30•30 Side Impact Protection O W N E R ’ S M A N U A L WARNING: Child Requirements: Weight limits: 30 pounds (13,5 kg) Do not install or use this infant restraint Maximum height: 30 inches (76 cm) until you read and understand all instructions in this manual.
  • Page 2: Table Of Contents

    Table of Contents Before You Start Installing the Car Seat on the Base Customer Service Installing the Car Seat without the Base Registration Form Installing the Seat with Different Types of Seat Belts Safety How to Buckle Your Baby into the Safety Rules Car Seat Your Car Seat...
  • Page 3: Before You Start

    Before You Start 1 Please read this manual carefully. Keep this manual in the plastic pocket on the base of the infant car seat. 2 Review car seat parts and read through instructions. Also read the labels. Read and understand all instructions before using this car seat. 3 Fill in and return the registration form (see page 4).
  • Page 4: Customer Service

    Customer Service Registration Form Important! Child restraints could be Call Peg Perego USA customer service at 1-800-671-1701 (toll free) for recalled for safety reasons. You must information about repairs or spare register this restraint to be reached parts. If any part is missing or damaged, in a recall.
  • Page 5: Safety

    Safety Warning manual for instructions on where to install an infant car seat in your • This car seat meets or exceeds all vehicle). applicable Federal Motor Vehicle Safety Standard 213 requirements for use in motor vehicles and aircraft. • Your child could be seriously injured if you do not follow instructions and warning labels correctly.
  • Page 6 vehicle manual. According to accident into the carrying position. statistics, children are safer when • Keep fingers away from moving parts. properly restrained in the rear seating • Use only approved parts. Use of positions than in the front seating unapproved parts can affect the safety positions.
  • Page 7: Safety Rules

    Safety Rules • Use only with children who weigh the straps and be seriously injured or between 5 and 30 pounds (2.3 and could move or tip the seat. 13,5 kg) and whose height is 30 inches • Do not leave the car seat or base (76 cm) or less.
  • Page 8: Your Car Seat

    Your Car Seat 5-POINT HOOD HARNESS SYSTEM Chestharnessclip Harnesslatchplate Harnessbuckle FRONT BACK Releaselever Seathandle SideImpact Headprotection Harnessstrap Anchorbuckles Slideadjuster Seatpadforinfant Harnessadjusterbutton EnergyabsorbingExpandedPolystyrene(EPS)foam Harnessadjusterstrap linedshellandheadrestforaddedimpactprotection. PrimoViaggioSIP-US_30-30_FIUS0908 8 26-10-2009 10:50:12...
  • Page 9: Your Car Seat Base

    Your Car Seat Base SIDE LOCKING CLIP STORAGE Belt slots with Level indicator anti-slip rubber pads FRONT BACK Level knob Lower connector system hereinafter Locking clip referred to as LATCH strap Anchor latches Instruction Manual book pocket PrimoViaggioSIP-US_30-30_FIUS0909 9 26-10-2009 10:50:13...
  • Page 10: Travel System

    Travel System Seat Duette SW Pliko P3 GT3/GT3 ForTwo Triplette SW Pliko Switch Aria Base Sì Aria Twin 6040 Skate PrimoViaggioSIP-US_30-30_FIUS09010 10 26-10-2009 10:50:13...
  • Page 11: Serial Numbers

    Serial Numbers The following information can be found under the front of the seat of the Primo Viaggio Sip 30•30 : product name, production date and serial number. Buckle production date. Harness production date. In the event of problems with the product, these details will be of use to customers.
  • Page 12: Installation Instructions

    Installation Instructions Peg Perego Primo Viaggio Sip 30•30 is certified for use with or without the base. Use of the base is highly recommended because it makes installation easier and therefore safer. ⇠ 12 PrimoViaggioSIP-US_30-30_FIUS09012 12 26-10-2009 10:50:13...
  • Page 13: Installing The Base

    Installing the Base When using Primo Viaggio Sip 30•30 with its base, first you install the base, and then you install the car seat on the base. Important! Read your vehicle manual for instructions on where to best install an infant car seat in your vehicle.
  • Page 14: How To Install The Base Using The

    I - How to Install the Base Using the LATCH SYSTEM Install the base with your vehicle parked on level ground. 1• Take the car seat off the base by moving the handle to the upright position. Place your hand on the top of the seat back and pull up on the handle with your fingers.
  • Page 15 3 • Remove the two anchor latches from their housings. The latches are on the sides of the base. First loosen the latch strap by pressing on the gray button and pulling the strap as shown. Then press the red button on top of the latch and pull the latch out of its housing.
  • Page 16 5• Make sure that the latch strap is threaded flat against the base. 6• Tighten the base against the seat by pulling the free end of the latch strap. Press down on the base with your body weight and tighten further.
  • Page 17: How To Install The Base Using Your

    II - How to Install the Base Using Your VEHICLE SEAT BELT Important! Not all seat belts work the same way. To make sure that the infant car seat is properly installed using your seat belts, read your vehicle owner’s manual. It will suggest proper placement of an infant car seat in your particular vehicle.
  • Page 18 3• Thread the lap belt through the slots on the base and lock the latch plate into the buckle as shown. 4• Pull the strap to tighten the seat belt. Press down on the base with your body weight and pull the strap tighter.
  • Page 19: Installing The Base With Different

    Installing the Base with Different Types of Seat Belts Primo Viaggio Sip 30•30 is designed for use with lap or lap/shoulder seat belts. Four of the most common types are listed below. Please read your vehicle manual for instructions on installing an infant car seat using your vehicle seat belts.
  • Page 20 III Lap/shoulder belt with a locking V Lap belt only with an Emergency latch plate Locking Retractor If you have a lap/shoulder belt with If you have a lap belt (without shoulder a locking latch plate and the belt strap) that locks only in an emergency comes loose after buckling, unbuckle (ELR), do not use it to secure the Primo it, flip it over, and re-buckle.
  • Page 21: How To Install The Locking Clip

    How to Install the Locking Clip To install the locking clip, hold the shoulder strap and lap belt together just above the buckle. Unbuckle the belt while holding the straps. Hook the locking clip around both straps as shown. Leave 1/2 inch space between the clip and latch.
  • Page 22: Different Types Of Vehicle Seat Belts

    Different Types of Vehicle Seat Belts Important! Do not install this car seat on seats with: A Lap/motorized shoulder belts. B Belts mounted on the door. C Side-facing seats. D Rear-facing seats or seats that rotate. For your child’s safety, always read your vehicle manual for instructions on installing child car seats.
  • Page 23: Installing The Car Seat On The Base

    Installing the Car Seat on the Base Now that you have installed the base in your vehicle, you are ready to install the car seat on the base. 1• Holding the car seat by the handle, press it rear facing on the base until you hear the click.
  • Page 24 2• Adjust the handle so it rests at the top edge of the car seat as shown. Any other position may injure your baby in an accident. To rotate the handlebar, press each of the round buttons (located on each side of the handle where it attaches to the seat) and rotate it to the position required.
  • Page 25: Installing The Car Seat Without The Base

    Installing the Car Seat without the Base Important! The base is designed to avoid consumer misuse by reducing the number of times the seat must be anchored to your vehicle. Please, use and install Primo Viaggio Sip 30•30 without the base only if needed. Park the vehicle on level ground.
  • Page 26 2• Adjust the restraint on the seat. Check the red line to see that the base is level with the ground. Thread the lap belt through the slots on the seat and lock the latch plate into the buckle as shown. 3•...
  • Page 27: Installing The Seat With Different

    Installing the Seat with Different Types of Seat Belts Installation of Primo Viaggio Sip 30•30 without base follows the same rules as with base regarding the availability of different types of vehicle seat belts. Important! For different types of seat belts, please refer to page 19 and 20.
  • Page 28: How To Buckle Your Baby Into The

    How to Buckle Your Baby into the Car Seat This restraint uses a 5-point harness system to secure your baby into the car seat. See illustration on page 1• Push the red buckle button to release the harness. Press and hold the harness adjuster button while pulling the shoulder straps out.
  • Page 29 3• Insert both latch plates into the buckle until you hear them click. Pull on straps to make sure that both plates are latched securely. (Note: You may need to adjust the shoulder height. See How to Raise or Lower the Shoulder Straps on page 33).
  • Page 30 5• To undo the chest clip, press the buttons on the side of the clip and pull apart as shown. 6• To undo the latch plates, press the red button and pull the latches up. ⇠ 30 PrimoViaggioSIP-US_30-30_FIUS09030 30 26-10-2009 10:50:18...
  • Page 31 7• Adjust the chest clip to the arm pit level. To tighten the harness, pull the adjuster strap at the bottom of seat until strap is snug. Make sure you leave one finger width between the harness and your baby’s collar bone. Tuck the loose end of the adjuster strap under the seat padding.
  • Page 32 9• As your baby grows, you may need to lengthen the shoulder straps. This is done by moving the harness straps to the second position on the slide adjuster as shown. Important! A snug strap should not allow any slack. It lies in a relatively straight line without sagging.
  • Page 33: How To Raise Or Lower The Shoulder Straps

    How to Raise or Lower the Shoulder Straps Primo Viaggio Sip 30•30 is fitted with a new and innovative feature to make strap adjustment easy and safe. Removing the shoulder strap and threading through the slots is not required anymore. 1•...
  • Page 34 2• The correct position is when the shoulder strap slot is located just below shoulder level, as shown. Important! This restraint is designed for infants up to 76 cm (30 inches) in length. The top of the infant head should not exceed the top of the seat back.
  • Page 35: Using The Car Seat Outside The Vehicle

    Using the Car Seat Outside the Vehicle This unit can be used as an infant seat. The special shell shape is designed for rocking your baby. The hood provides shade for your baby. 1• To rock your baby, move the handle into the up position as shown.
  • Page 36 2• To attach the hood, push the hood latch into the slot on the seat shell as shown. To open the hood, pull the frame until it clicks open. 3• To adjust the hood position, simply push into the desired position. 4•...
  • Page 37 5• Carrying handle for Base. Warning! Do not use with the seat attached to the base. Warning! Do not use as a means of transporting child. ⇠ 37 PrimoViaggioSIP-US_30-30_FIUS09037 37 26-10-2009 10:50:22...
  • Page 38: How To Use The Car Seat On Aircraft

    How to Use the Car Seat on Aircraft without Base This unit is certified for aircraft use. 1• Position the restraint on the seat, adjust the handle so it rests at the top edge of the car seat as shown. Any other position may injure your baby in an accident.
  • Page 39 How to Use the Car Seat on Aircraft with Base This unit is certified for aircraft use. 1 • Buckle the base to the aircraft seat using the lap belt as shown. A secondary belt path can also be used as shown in Fig.
  • Page 40 tighten the belt further. Position the car seat rear facing over the base. Press the seat into the base until you hear the click. Make sure the seat is correctly locked in place. Important! Follow the harness instructions beginning with “How to Buckle Your Baby into the Car Seat”...
  • Page 41: Cleaning And Maintenance

    Cleaning and Maintenance This unit needs minimal maintenance. • Keep all moving parts clean. Lubricate with light oil, if necessary on moving parts. • Clean the plastic parts often with a damp cloth. Do not use solvents or harsh products. •...
  • Page 42: How To Wash The Chair Padding

    How to Wash the Chair Padding - Cover removal 1• To remove the safety seat harness: • Press the harness adjuster button in the centre of the seat to extend the safety harness straps; • Press the red button on the crotch strap buckle to release the harness;...
  • Page 43 • Unscrew the two headrest screws with a screwdriver, press the teeth on the slots and pull the headrest to release it. 3• To remove the padding: • Slide off the four padding fixing tabs from the edge of the safety seat; •...
  • Page 44 How to Wash the Chair Padding - Refitting 1• To refit the padding: • Slide on the padding; • Insert the four padding fixing wings on the edge of the safety seat; • Reposition the harness adjuster button cover in the centre of the safety chair and engage it from under the chair;...
  • Page 45 with the headrest. • Screw on the headrest and replace the cover. 3• To refit the safety harness: Important! make sure the straps are not twisted. • Insert the harness braces from the front of the safety seat, first through the shoulder covers and then through the headrest slots, attaching them to the metal buckle at the back...
  • Page 46: Replacement Parts

    Replacement Parts 1) BSAUNI• 2) SPST6491GR 3) SPST6341DGR 4) SPST6341SGR 5) SAPI5714GR 6) BCAUNI• 7) MUCI0055GR 8) BAKUNI• 9) ASPI0086GL 10) SAPI6475NFGR 11) IAKADJUSNF NOTE: Spare parts available in different colors* to be specified when ordering. NOTE: A Tether is not a component of a rear facing only car seat.
  • Page 47 PrimoViaggioSIP-US_30-30_FIUS09047 47 26-10-2009 10:50:26...
  • Page 48 PrimoViaggioSIP-US_30-30_FIUS09048 48 26-10-2009 10:50:26...
  • Page 49 PrimoViaggioSIP-US_30-30_FIUS09049 49 26-10-2009 10:50:27...
  • Page 50 PrimoViaggioSIP-US_30-30_FIUS09050 50 26-10-2009 10:50:27...
  • Page 51 PrimoViaggioSIP-US_30-30_FIUS09051 51 26-10-2009 10:50:27...
  • Page 52 PrimoViaggioSIP-US_30-30_FIUS09052 52 26-10-2009 10:50:27...
  • Page 53 PrimoViaggioSIP-US_30-30_FIUS09053 53 26-10-2009 10:50:27...
  • Page 54 PrimoViaggioSIP-US_30-30_FIUS09054 54 26-10-2009 10:50:27...
  • Page 55 PrimoViaggioSIP-US_30-30_FIUS09055 55 26-10-2009 10:50:28...
  • Page 56 PrimoViaggioSIP-US_30-30_FIUS09056 56 26-10-2009 10:50:28...
  • Page 57 PrimoViaggioSIP-US_30-30_FIUS09057 57 26-10-2009 10:50:28...
  • Page 58 PrimoViaggioSIP-US_30-30_FIUS09058 58 26-10-2009 10:50:28...
  • Page 59 PrimoViaggioSIP-US_30-30_FIUS09059 59 26-10-2009 10:50:28...
  • Page 60 PrimoViaggioSIP-US_30-30_FIUS09060 60 26-10-2009 10:50:29...
  • Page 61 PrimoViaggioSIP-US_30-30_FIUS09061 61 26-10-2009 10:50:29...
  • Page 62 PrimoViaggioSIP-US_30-30_FIUS09062 62 26-10-2009 10:50:29...
  • Page 63 PrimoViaggioSIP-US_30-30_FIUS09063 63 26-10-2009 10:50:29...
  • Page 64 PrimoViaggioSIP-US_30-30_FIUS09064 64 26-10-2009 10:50:30...
  • Page 65 PrimoViaggioSIP-US_30-30_FIUS09065 65 26-10-2009 10:50:30...
  • Page 66 PrimoViaggioSIP-US_30-30_FIUS09066 66 26-10-2009 10:50:30...
  • Page 67 PrimoViaggioSIP-US_30-30_FIUS09067 67 26-10-2009 10:50:30...
  • Page 68 PrimoViaggioSIP-US_30-30_FIUS09068 68 26-10-2009 10:50:30...
  • Page 69 PrimoViaggioSIP-US_30-30_FIUS09069 69 26-10-2009 10:50:30...
  • Page 70 PrimoViaggioSIP-US_30-30_FIUS09070 70 26-10-2009 10:50:31...
  • Page 71 PrimoViaggioSIP-US_30-30_FIUS09071 71 26-10-2009 10:50:31...
  • Page 72 PrimoViaggioSIP-US_30-30_FIUS09072 72 26-10-2009 10:50:32...
  • Page 73 PrimoViaggioSIP-US_30-30_FIUS09073 73 26-10-2009 10:50:32...
  • Page 74 PrimoViaggioSIP-US_30-30_FIUS09074 74 26-10-2009 10:50:32...
  • Page 75 PrimoViaggioSIP-US_30-30_FIUS09075 75 26-10-2009 10:50:33...
  • Page 76 PrimoViaggioSIP-US_30-30_FIUS09076 76 26-10-2009 10:50:33...
  • Page 77 PrimoViaggioSIP-US_30-30_FIUS09077 77 26-10-2009 10:50:33...
  • Page 78 PrimoViaggioSIP-US_30-30_FIUS09078 78 26-10-2009 10:50:34...
  • Page 79 PrimoViaggioSIP-US_30-30_FIUS09079 79 26-10-2009 10:50:34...
  • Page 80 PrimoViaggioSIP-US_30-30_FIUS09080 80 26-10-2009 10:50:34...
  • Page 81 PrimoViaggioSIP-US_30-30_FIUS09081 81 26-10-2009 10:50:34...
  • Page 82 PrimoViaggioSIP-US_30-30_FIUS09082 82 26-10-2009 10:50:34...
  • Page 83 PrimoViaggioSIP-US_30-30_FIUS09083 83 26-10-2009 10:50:34...
  • Page 84 PrimoViaggioSIP-US_30-30_FIUS09084 84 26-10-2009 10:50:35...
  • Page 85 PrimoViaggioSIP-US_30-30_FIUS09085 85 26-10-2009 10:50:36...
  • Page 86 PrimoViaggioSIP-US_30-30_FIUS09086 86 26-10-2009 10:50:36...
  • Page 87 PrimoViaggioSIP-US_30-30_FIUS09087 87 26-10-2009 10:50:36...
  • Page 88 PrimoViaggioSIP-US_30-30_FIUS09088 88 26-10-2009 10:50:36...
  • Page 89 PrimoViaggioSIP-US_30-30_FIUS09089 89 26-10-2009 10:50:36...
  • Page 90 PrimoViaggioSIP-US_30-30_FIUS09090 90 26-10-2009 10:50:36...
  • Page 91 PrimoViaggioSIP-US_30-30_FIUS09091 91 26-10-2009 10:50:36...
  • Page 92 PrimoViaggioSIP-US_30-30_FIUS09092 92 26-10-2009 10:50:37...

Table of Contents