Advertisement
Connection Diagram
REAR VIEW
Home Docking Cradle for JVC Sirius tuner
Using the Speaker System
1
Connect the speakers and AC adapter as shown in the Connection Diagram.
2
Turn the power switch knob clockwise to turn the power on.
A click sound is heard and the power lamp lights up in green.
3
Turn the power switch knob further to obtain the optimum sound level.
• In case the sound level is not sufficient though the knob is turned up fully clockwise,
increase the output level of the signal source as it may be set too low.
• When using the headphones, plug it into the headphone jack. No sound comes out of the
speakers.
Turn the knob fully counterclockwise before connecting the headphones, not to damage
the speakers and your ears.
To turn off the speakers, turn the power switch knob fully counterclockwise.
• Never turn it on or off by any other means to ensure safe operation of the speakers.
Parts Identification
7 Front
Left speaker
7 Rear
Right speaker
Line-input cord
(green plug):
2 m (6.5 ft)
Audio Output (Green connector)
Green plug
(stereo mini:
φ 3.5 mm)
Line input cord
Right speaker
Power lamp
Headphone jack
Power switch
(volume control) knob
Left speaker
DC IN jack
L SPKR (left speaker) jack
(brown connector)
Left speaker cord
(brown plug):
2 m (6.5 ft)
Right Speaker
Black plug
Maintenance
If cleaning is required, disconnect the AC adapter from AC outlet, and wipe off with soft cloth.
For removing heavy stain, use the cloth moistened with neutral detergent.
Do not use inflammable or harmful fluid such as benzine or thinner.
Troubleshooting
Check the following if you think the system is not working correctly.
• If the problem should persist, unplug the AC adapter from the AC outlet, and refer servicing
to the qualified service personnel.
Symptom
Possible Cause
Power lamp is
• AC adapter is not connected.
turned off.
• No power is supplied.
Power lamp is turned
• Line-input cord is not connected.
on, but no sound.
• Volume level is too low.
Sound is distorted.
• Volume level is too high.
• Input sound level is too high.
Sound level is too low.
• Input sound level is too low.
Sound comes out of
• Line-input cord is not connected firmly.
only one speaker.
• Left speaker is not connected to the
right speaker.
Although the speakers are magnetically shielded, they may affect some monitors if installed
nearby. Should color deterioration occur on a monitor, place the speakers slightly away.
Turn off the monitor, and keep it turned off for about 15 to 20 minutes.
By doing this, normal color will be restored.
Specifications
7 Amplifier:
Power output
Input impedance
Input sensitivity
Power supply
Power consumption
Signal-to-noise ratio
7 Power Requirements:
7 Speaker System: Enclosures
Frequency response
Speaker uint
7 Dimensions (H/W/D):
Right speaker:
Left speaker:
7 Mass:
Right speaker: 400 g (0.89 lbs)
* Design and specifications are subject to change without notice.
REAR VIEW
Left Speaker
Brown connector
Brown plug (mini: φ 2.5 mm)
Left speaker cord
AC adapter
(AC 120 V
, 60 Hz)
To an AC outlet
After completing all other connections,
plug in the AC adapter.
Remedy
• Plug in adapter firmly.
• Try another AC outlet.
• Plug in the cord firmly.
• Turn up the volume control.
• Turn down the volume control.
• Adjust it to the optimum level.
• Adjust it to the optimum level.
• Plug in the cord firmly.
• Plug in Speaker cord firmly.
1.5 W per channel (at 10 % THD)
12 kΩ (nominal)
200 mV/1 kHz/1 W
DC 9 V 500 mA (by AC adapter)
12 W
72 dB
AC 120 V
, 60 Hz
Plastic molded
100 Hz – 20 000Hz
9
90 mm x 50 mm (3-
/
in. x 2 in.) cone type,
16
magnetically shielded
200 mm x 80.5 mm x 112 mm
7
1
7
(7-
/
in. x 3-
/
in. x 4-
/
in.)
8
4
16
200 mm x 80.5 mm x 99.3 mm
(7-
7
/
in. x 3-
1
/
in. x 3-
15
/
in.)
8
4
16
Left speaker: 345 g (0.77 lbs)
Advertisement
