Using The Wall-Mounted Door Control; To Open The Door Manually - Chamberlain M3100M-1/2HP Owner's Manual

Using the Wall-Mounted
Door Control
Press the push bar/button to
open or close the door. Press
again to reverse the door
during the closing cycle or to
stop the door while it's
opening.
THE MULTI-FUNCTION DOOR CONTROL
Light feature
Press the Light button to turn the opener light on or off. It
will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the
light will remain on for 4-1/2 minutes. Press again to turn it
off sooner. The 4-1/2 minute interval can be changed to
1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold
the Lock button until the light blinks (about 10 seconds). A
single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close
from the Door Control, the Outside Keylock and the
Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The push bar light will flash as long as the Lock feature is
on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The Lock
feature will also turn off whenever the "Learn" button on
the motor unit panel is activated.
Additional features when used with the
3-Button hand-held remote
A) To control the opener lights:
In addition to operating the door, you may
program the remote to operate the lights.
1. With the door closed, press and hold a small remote
button that you want to control the light.
2. Press and hold the Light button on the Multi-Function
door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights flash, release all buttons.
B) To operate one door using all three
You may program the remote to open
Push
the door with the large button, close it
Bar
with the middle button, and stop the
Push
Lock
door's movement with the third button.
Button
Button
NOTE: If remote is already programmed, you must first
Light
Button
erase all codes. See Programming.
1. With the door closed, press and hold the large remote
push button.
2. Press and hold the Lock button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.

To Open the Door Manually

To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage
• NEVER use emergency release handle unless garage doorway
• NEVER use handle to pull door open or closed. If rope knot
The door should be fully closed if
possible. Pull down on the
emergency release handle and lift
the door manually. To reconnect
the door to the opener, press the
door control push bar.
The lockout feature prevents the
trolley from reconnecting
automatically. Pull the emergency
release handle down and back
(toward the opener). The door can
then be raised and lowered
manually as often as necessary.
To disengage the lockout feature,
pull the handle straight down. The
trolley will reconnect on the next
UP or DOWN operation, either
manually or by using the door
control or remote.
27
buttons on the hand-held remote:
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
is clear of persons and obstructions.
becomes untied, you could fall.
Open
Stop
Close
Trolley
Release
Emergency
Arm
Release
Handle
(Pull Down)
MANUAL DISCONNECT
POSITION
Trolley
Release
Arm
Emergency
Release Handle
(Down and Back)
LOCKOUT POSITION