Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Scantronic 8136
Summary of Contents for Scantronic 8136
-
Page 1: User Guide
USER GUIDE 8136 HARDWIRED CONTROL PANEL Scantronic Leading the way in security... -
Page 2: Table Of Contents
Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Scantronic accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice. -
Page 3: Introduction
1. Introduction The 8136 System zones unset unset Levels 24 hour panic alarm access code Note: Ask your Installer for details of any features mentioned in this manual. Many of them are options that the installation engineer can select while programming the system. -
Page 4: Glossary
Glossary 496256 Issue 1... - Page 5 496256 Issue 1...
-
Page 6: Using The Keypad
Using the Keypad Levels LEDs (Set or Unset) 32 character by two line Liquid Crystal Display Power (LCD) Optional programmable panic alarm keys. Press Level setting keys keys 1 and 3 together Optional programmable control function keys. Press keys 7 and 9 together. -
Page 7: About This Guide
About This Guide 496256 Issue 1... -
Page 8: Everyday Operation
2. Everyday Operation Keyswitch) exit route entry route Note: The system may be programmed so that your access code can set some Levels but not others. See "6. Supervisor". Setting the System Timed Setting exit time. exit tone 496256 Issue 1... -
Page 9: Final Door
does not set. Note: Some Levels on your system may be programmed for Silent Set. When setting these Levels the system does not give any tones from the keypads. Final Door Exit Terminate Button Note: The Installer may have programmed your system to set after a fixed time even if you do not press the exit terminate button. -
Page 10: Keyswitch Setting
Keyswitch Setting Setting an Area If the System Will Not Set fault trouble 496256 Issue 1... -
Page 11: If The System Will Not Set
The system will not set until you have cleared all the faults. Zones giving trouble reports do not affect the system security. Your alarm system will still work correctly. Contact your alarm company to let them check the system. 496256 Issue 1... -
Page 12: Unsetting The System
Unsetting the System If You Have a Keyswitch Using the Keypad entry time entry tone The system is now unset. WARNING: If you enter your premises and the keypad is silent then there may be an intruder. Tamper Faults 496256 Issue 1... -
Page 13: After An Alarm
3. After an Alarm disarm reset Fire Alarm Disarming the System Resetting the System Customer Reset Engineer Reset Remote Reset 496256 Issue 1... -
Page 14: Customer Reset
Customer Reset From Keypad Using a Keyswitch Engineer Reset Remote Reset (CSID Code) 496256 Issue 1... -
Page 15: Redcare Or Pc Reset
RedCare or PC Reset 496256 Issue 1... -
Page 16: Special Functions
4. Special Functions Introduction omitted chime Omitting Zones (Menu + Level) Menu 496256 Issue 1... -
Page 17: Omitting 24 Hour Zones (Menu 2)
Note: You can also key in the zone number of the zone you want to omit. For example, key in '005' for zone 5, or '025' for zone 25. Omitting 24 Hour Zones (Menu 2) Menu 496256 Issue 1... -
Page 18: Turning The Chime On/Off (Menu 3)
Turning the Chime On/Off (Menu 3) Menu Changing the Volume of the Internal Sounder Menu Testing the System (Menu 4) walk test 496256 Issue 1... -
Page 19: Walk Test
Note: If your system is fitted with Fire, 24 hour or personal attack detectors, you cannot walk test them. If you wish to test them call your alarm company. Walk Test Menu Note: You can abandon the test at any time by pressing Menu. Bell Test Menu 496256 Issue 1... -
Page 20: Call Out To Central Station (Menu 5)
Note: You can abandon the test at any time by pressing Menu. Call Out to Central Station (Menu 5) Menu 4 and 6 Setting the Time and Date (Menu 6) 496256 Issue 1... -
Page 21: Changing Summer/Winter Time
Menu Changing Summer/Winter Time Menu 496256 Issue 1... -
Page 22: Changing Area And Zone Names (Menu 7)
Changing Area and Zone Names (Menu 7) 496256 Issue 1... -
Page 23: To Change Area Names
To Change Area Names: Menu 496256 Issue 1... -
Page 24: To Change Zone Names
To Change Zone Names Menu 496256 Issue 1... -
Page 25: Using The Log (Menu 9)
Using the Log (Menu 9) Menu 496256 Issue 1... - Page 26 001: 13:09:55 27/3/96 U02:A02:UNSET Audit Number (not shown Event Date (day, on keypad displays) month, year) Event Time (hour, Event Description (user minute, second) number, area number, event) Notes: In the event description you may see the following user numbers: when the installer has been programming the system.
-
Page 27: Programming Chart
5. Programming Chart Access Code + Access Code + Access Code + Access Code + ENTER ENTER ENTER ENTER Use Level keys to select Press A or B to change Press C or D until the Press 4 and 6 together. Level. - Page 28 Access Code + Access Code + Menu + 8 Menu + 7 (Supervisor and restricted access for Master User) ENTER ENTER ENTER ENTER ENTER Press A or B to select ENTER user number*. ENTER Key in new name. Press A or B until the Press A or B until the display shows the area display shows the zone...
-
Page 29: Supervisor
6. Supervisor Introduction Access Codes Restricting Users to Partitions Partition 496256 Issue 1... -
Page 30: Master Users
Note: Any user with access to one Level in a Partition also has access to all the other Levels in the same Partition. Master Users Duress Code Duress Code Restricting users to Arm Only Arm Only Changing Access Codes and User Privileges (Menu 8) 496256 Issue 1... -
Page 31: Changing User Names
Menu Changing User Names Changing Access Codes 496256 Issue 1... -
Page 32: Changing Partition Access
Note: If your system is using six-digit access codes the bottom line of the display will show "******". Note: To delete an existing code key in "0000" ("000000" for six digit access codes). Changing Partition Access 496256 Issue 1... -
Page 33: Setting Up A Duress Code
Setting Up a Duress Code 496256 Issue 1... -
Page 34: Giving A User Arm Only Access
Giving a User Arm Only Access Allowing a User to Omit Zones 496256 Issue 1... -
Page 35: Giving A User Log Access
Giving a User Log Access Allowing a User to Change Zone Names 496256 Issue 1... -
Page 36: Allowing A User To Reset After An Alarm
Allowing a User to Reset After an Alarm Allowing a User to Change the Time and Date. Creating a Master User 496256 Issue 1... -
Page 37: User Records
User Records DO NOT Disabling Remote Setting Menu 496256 Issue 1... -
Page 38: Index
Index defintion ..............4 Symbols definition ..............4 definition ..............4 changing ............... 31 definition ..............4 definition ..............4 definition ..............4 setting up .............. 34 how to ..............19 definition ..............4 changing volume ........... 18 call out to .............. 20 turning on/off ............ - Page 39 deleting ..............23 definition ..............5 changing ............... 31 24 hour zones ............17 definition ..............5 granting access ............. 34 how to ..............16 how to ..............19 description .............. 5 keys ................. 7 definition ..............5 problems ............... 11 definition ..............
- Page 40 496256 Issue 1...