Subscribe to Our Youtube Channel
Related Manuals for Scantronic 9449
Summary of Contents for Scantronic 9449
- Page 1 INSTALLATION AND PROGRAMMING GUIDE HARDWIRED CONTROL PANEL Scantronic Leading the way in security...
- Page 2 Every effort has been made to ensure that the contents of this book are correct, errors and omissions excepted. However, neither the authors nor Scantronic accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice.
-
Page 3: Table Of Contents
Contents Contents 1. INTRODUCTION ..................1 Operator Controls and Displays ....................2 System Features ........................... 3 Detectors ..............................3 Full Setting ..............................3 Exit Times ..............................3 Part Setting ..............................4 Entry and Unsetting the System ......................... 4 Alarm .......................... - Page 4 Contents Entry/Exit Chime (Command 08) ......................25 Zone Omitted in Part Set (Command 10) ....................25 Change Engineer Code (Command 20) ....................26 Change User Codes (Commands 21, 22 and 23) ..................26 Part Set Exit Mode (Command 35) ......................27 Rearm (Command 40) ..........................
-
Page 5: Introduction
1. Introduction 1. INTRODUCTION The 9449 is a fully programmable 8 zone alarm system control unit with Full and Part Set, designed for domestic and small commercial installations. Before installing the alarm system, make sure you are familiar with the functions, system plans, and detectors described in this manual. -
Page 6: Operator Controls And Displays
1. Introduction Operator Controls and Displays Figure 2 shows the 9427 remote keypad. << >> Part Power Bell - test - Walk Code Fault Service Chime Clock Tamper OMIT ENTER Figure 2. 9427 Remote Keypad. On the remote keypads the LEDs display the following functions: ENTRY/EXIT Shows the state of the entry/exit zone. -
Page 7: System Features
1. Introduction ENTER Used to enter programming and setting/unsetting com- mands. Used to display the last 10 alarms and tampers. OMIT Used to set the system with individual zones temporarily omitted. When both keys 1 and 3 are pressed together the system gives a PA alarm. -
Page 8: Part Setting
1. Introduction Part Setting The installer can program the system so that certain zones are omitted if the user sets the system by keying "2 + ENTER + (access code)". The part set system may need a separate Entry/Exit zone from the full set system. -
Page 9: Re-Arm
1. Introduction Re-Arm The installer can program the system to rearm after an alarm. With this option selected, the control unit stops the sounder and strobe at the end of its programmed time and rearms ready for another activation. See Com- mand 40 in "4. -
Page 10: Engineer Access
1. Introduction Engineer Access The installer gains access to system programming by keying in 0 followed by # (ENTER) and a 4-digit Engineer Access Code (default 7890). The Installer can change the Engineer Access Code at any time while in programming mode. -
Page 11: Technical Description
2. Technical Description 2. Technical Description Specification Operating temperature = -10º to +55ºC Humidity = 96% RH Dimensions = 243mm W, 234mm H, 87mm D Weight = Approx 3.0 kg (without stand-by battery) Conforms to EN50131-1 Grade 1 and 2 and current BS4737 Part 1 for remote signalled systems, ACPO-IAS Policy, NACOSS NACP14, ABI log requirements. -
Page 12: Control Unit Pcb And Case
2. Technical Description Control Unit PCB and Case Figure 3 shows the layout of the control unit PCB. Battery Connector 21VAC Fuse 12V Batt Fuse 21VAC Supply from Transformer 12V Aux Fuse Entry/Exit tones volume control Lid Anti-Tamper Communicator connector Printer Connector Connector block RST Pins... -
Page 13: Installation
3. Installation 3. INSTALLATION Overview Installing the alarm system comprises the following steps: Run cables from the position of the detectors, keypad(s), internal and external sounders to the control unit position. Fit the control unit case back. Fit remote keypad(s), detectors, internal and external sounders in their chosen locations. -
Page 14: Fitting The Control Unit Pcb
3. Installation Fitting the Control Unit PCB. Figure 5. Fitting Control Unit PCB Fit the removable support pillar into the case back. Secure the PCB to the support pillars with the screws provided (Figure 5). Make sure that the bottom left corner of the PCB is seated on its support pillar. -
Page 15: Wiring The Control Unit
3. Installation Mark, drill and plug the position of two more mounting holes. Fix the keypad back in place with two more screws. Figure 6. 9427 Backplate Wiring the Control Unit Cable Entries The control unit case back provides several cable entries. The back is designed to stand away from the wall to leave space for cables. -
Page 16: Connecting A 9427 Remote Keypad
3. Installation Note that the control unit does not have an internal mains fuse. All electrical connections should be carried out by a qualified electrician and must comply with the current IEEE Wiring Regulations: 16 Edition, Appendix 5 - Standard Circuit Arrangement. -
Page 17: Keypad Addressing
3. Installation Keypad Addressing The 9449 control unit is supplied with one remote keypad. If you have fitted more keypads then each one must be given a separate "address". Links LK1 to LK3 set the keypad address, as shown in Figure 9. -
Page 18: Wiring Example
3. Installation Figure 10. Detector Circuit Connections +9V nominal Figure 11. Connecting a Pressure Mat Wiring Example Figure 12 shows an example system wired for two detectors. Note that mains and battery connections are not shown. Notes: 1. Power for detectors is available from two terminals on the control unit PCB marked "+ - 12V AUX". - Page 19 3. Installation 16 Ohm Loudspeaker (2 Max. in parallel) Bell Strobe Typical SAB Bell 6-core -ve Hold Off -ve Tamper Return +ve Hold Off -ve Apply trig Z1 PIR 6-core Terminal connector for Anti-Tamper loop (not supplied) EE Door Contact 4-core 9427 Keypad 4-core...
-
Page 20: Wiring Examples For Programmable Output
+ve 12V Aux Figure 13. Programmable Output Wiring Examples Fitting a Communicator The 9449 can be fitted with a communicator or speech dialler (for example the Scantronic 8400, 8440, 660 or RedCare STU). To fit a communicator, follow the instructions below. - Page 21 3. Installation Figure 14. Fitting a Communicator Make any necessary connections from the communicator to the Comms Wiring Harness. Figure 15 shows the outputs available on the free ends of the .Comms Wiring Harness. Figure 15. Communications Wiring Harness. Plug the Comms Wiring Harness onto the communications connector on the main PCB (see Figure 3).
-
Page 22: Fitting A Battery
3. Installation If the system has already been installed: Re-connect the battery. Fit the case lid (don't forget to attach the earth lead from the case to the left hand support pillar, see Figure 4). Apply mains power. Test communicator operation. Fitting a Battery Fit a rechargeable battery into the back of the case. -
Page 23: Programming
4. Programming 4. PROGRAMMING Initial Start Up Before applying power to the control unit, ensure that any remote keypad(s), all zone circuits and sounders are connected. Connect the battery to the control unit PCB. The green power LED flashes and the internal sounder may sound. Ignore any other lights Key-in the factory default user access code: 1234. -
Page 24: Engineer Program Command List
4. Programming Engineer Program Command List To change: Key-in Command: followed by: Notes Default Zone n x...x # n = zone number (1 to 7) 0n # (see "Zone Programming" x = Zone type, one or more of: on page 23) 0 = Not Used (see Note 8) Ö... - Page 25 4. Programming To change: Key-in Command: followed by: Notes Default Ö Entry time 43 # 10 seconds 20 seconds 30 seconds 45 seconds 1 minute 2 minutes Ö Exit time 44 # 10 seconds 20 seconds 30 seconds 45 seconds 1 minute 2 minutes Ö...
-
Page 26: Zone Programming
4. Programming To change: Key-in Command: followed by: Notes Default Comms O/P 1 Type 71 # Not used Ö Fire Alarm Open/Close Alarm Abort Technical Alarm Confirmation Comms O/P 2 Type 72 # See command 71 Comms O/P 3 Type 73 # See command 71 Burg... -
Page 27: To Re-Enter Programming Mode
4. Programming 1. Key in 07#. 2. Key in 0. 3. Key in 1, 6 and 7. The display shows: The display shows: The display shows: The right hand The right hand The right hand column indicates a column indicates a column indicates a value of 4 = Fire value of 0 = Not... -
Page 28: Restoring Factory Default Programming (2Nd Stage Reset)
4. Programming Place a small screwdriver blade to short between the 'RESET' pins. With the blade still across the pins, apply battery power. The keypads give a double "beep". Remove the screwdriver blade, and then re-apply mains power. Key in 1234. Key in 0 then # followed by 7890. -
Page 29: Zone Attributes
4. Programming Fire (4) Smoke or heat detectors connected to FR type zones cause the speakers to give a distinctive fire signal (inter- nal sounders pulsing “Dee Dah Dee Dah...”). Fire alarms operate whether the system is set or unset and cannot be omitted, and will always trigger communications if fitted. -
Page 30: Change Engineer Code (Command 20)
4. Programming The zone LED glows if the zone will be omitted during part set. (Read the zone number from the right hand figures in blue, see Figure 17.) 2. Key the zone number again to make sure the zone is included when the system is set (the zone LED will go out). -
Page 31: Part Set Exit Mode (Command 35)
4. Programming If the Duress code is enabled and used, then the system gives a silent alarm. Once a user enters the duress code the system allows access in the normal way. However, if a communicator is fitted, the system immediately sends a PA signal. -
Page 32: Output Programming (Commands 51)
4. Programming Terminate (option 1). Use this option if the user wants to complete setting the system by pressing an exit terminate button. The button must be connected across the ET terminals of a keypad. The system gives an infinite exit time, but sets seven seconds after the user presses the button. -
Page 33: Zone 3 As Additional Ee Zone (Command 54)
4. Programming Local Audibles (option 1) The system triggers external and internal sounders, but does NOT use the communicator. Internal Sounder (option 2) The system uses the internal sounders, but NOT the external sounder or communicator. Zone 3 as Additional EE Zone (Command 54) If you wish to provide an additional Entry/Exit zone, then use Command 54 option 1 to make zone 3 an EE zone. -
Page 34: Csid Code (Command 62)
4. Programming display. The central station verifies the user's identity, then enters the code number into a special programmer. The programmer generates a ‘Reset Code’, which the central station gives back to the user. The user then enters the ‘Reset Code’ at the keypad to reset the system. To allow the customer to use ‘Anti Code Reset’... -
Page 35: Pa Response (Command 66)
4. Programming PA Response (Command 66) This command selects how the system responds when a PA zone operates. Audible PA (option 0) The system operates the sounders and lights the FAULT and any PA zone LEDs. If a communicator is fitted the system sends a PA message to the central station. -
Page 36: Line Fault Response (Command 75)
4. Programming Technical Active when technical alarm zone triggered. Alarm Confirmation Active when second zone triggered during an alarm. (Alarm confirmation must be enabled with command 65.) For example, to send Alarm Abort on output 4 (green) key in: 74 # 5 #. Line Fault Response (Command 75) If the communicator detects a telephone line fault it will signal the control unit by applying a positive voltage to the Line Fail input (blue) on the Comms... -
Page 37: Testing
5. Testing 5. Testing You may test parts of the system by entering commands at the keypad. To carry out a test make sure the system is in programming mode and then key in one of the following commands. Press * (Omit) to end each test: 90 # To print the event log. -
Page 38: Printing The Log
Printing the Log To print the event log, make sure the system is in programming mode, then Key in 90 #. Figure 19 below shows a sample of a printed log. 9449 02-Sep, 08:51, Installer Access 02-Sep, 08:50,... -
Page 39: Engineer Walk Test (Command 97)
5. Testing Engineer Walk Test (Command 97) Allows the engineer to test all devices on the system. Enter programming mode. Key in "97 #" The system gives a continuous tone. Open and close each detector contact in turn. When a detector contact is open the system gives an interrupted tone and flashes the zone LED. -
Page 40: Fault Finding
6. Fault Finding 6. Fault Finding The diagrams below show typical displays during faults. sounder Flashing Power Power Power Fault Fault Fault Service Service Service Tamper Tamper Tamper Alarm (zone 1). Alarm (zone 1). Fire, 24Hr, Technical Customer reset Engineer reset or PA zone active. - Page 41 6. Fault Finding Power Power Power Fault Fault Fault Service Service Service "beep" Tamper Tamper Tamper Tamper (lid, remote Clear tamper fault and Battery low - no mains. keypad, sounder, reset. "beep" every 5s. global tamper). Needs engineer reset. Power Fault Service Tamper...
-
Page 42: Index
Index 67 ................31 Index 68 ................31 71 to 74 ..............31 75 ................32 90 ................33 Symbols 96 ................33 97 ..............33, 35 24Hr monitored ........25 Communicator ........4, 16 fitting ..............16 output ..............7 output type ............ - Page 43 Index silent ..............31 Panic alarm ..........24 Part key ............. 3 Humidity ............ 7 Part set ..........4, 5 alarm response ............. 28 entry exit zone ............4 exit mode ............... 27 Inputs ............7 silent ................ 4 PIR set latch ..........5 Installation overview .........
- Page 44 Index Walk test .......... 33, 35 key ................3 Weight ............7 Zone description .............. 3 programming ............24 types ..............24 wiring ..............13 Zone 1 in part set ........28 Zone 3 as EE zone ......... 29 Zone attributes ........25 Zone omitted in part set ......
- Page 45 Manufactured in the UK by Scantronic Ltd. Product Support (UK) - T el - (0891) 616343 between 09:00 and 17:30, Monday to Friday. (CALLS CHARGED AT 50P PER MINUTE) PRODUCT SUPPORT FAX NO. (01594) 544136. Part No. 496282 Issue 1...
Need help?
Do you have a question about the 9449 and is the answer not in the manual?
Questions and answers