Sanyo PDG-DHT8000L Service Manual page 56

Electrical Adjustment
Grp / No. Item
3 AutoWait
4 CHECK - Tolerance
5 Time out wait
100 Route Switch *
261 Auto Calibration (RGB)
0 OFFSET AREA H START
1 OFFSET AREA V START
2 GAIN AREA H START
3 GAIN AREA V START
4 Image AREA H WIDTH
5 Image AREA V HEIGHT
6 OFFSET Target
7 OFFSET Tolerance
8 GAIN Target
9 GAIN Tolerance
10 Image Level Tolerance
262 Auto Calibration (CVBS/SVIDEO) PW392-AFE MDL <10bits>
0 Y Image Area Start X
1 Y Image Area Start Y
6 Image Area H WIDTH
7 Image Area V HEIGHT
8 Y Target Level
11 Gain Tolerance
12 Image Level Tolerance
264 Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START
1 Y-OFFSET AREA V START
2 CB - OFFSET AREA H START
3 CB - OFFSET AREA V START
4 CR - OFFSET AREA H START
5 CR - OFFSET AREA V START
6 Y - GAIN AREA H START
7 Y - GAIN AREA V START
8 CB - GAIN AREA H START
9 CB - GAIN AREA V START
10 CR - GAIN AREA H START
11 CR - GAIN AREA V START
12 Image AREA H WIDTH
13 Image AREA V HEIGHT
14 Y - OFFSET TARGET
15 CB OFFSET TARGET
16 CR OFFSET TARGET
17 Y - GAIN TARGET
18 CB - GAIN TARGET
19 CR - GAIN TARGET
20 OFFSET Tolerance
21 GAIN Tolerance
22 Image Level Tolerance
280 Auto PC Adjust
0 AutoPCAdjustEnable
1 Frequency Step
2 Frequency Threshold
3 Fine Phase
4 BLKDET
5 PHASEMSK
300 Closed Caption
2 Multi Window Caption
Function
Waiting time
Tolerance of Offset
Wait Time until Time out [sec.]
0: Menu
1: Input1 - RGB Analog (OnBoard - Ext.ADC)
2: Input3 - RGB Analog (Slot - Ext.ADC)
3: Input1 - RGB Analog (OnBoard - Int.ADC)
4: Input2 - YCbCr (OnBoard - Ext.ADC)
5: Input2 - YCbCr (OnBoard - Int.ADC)
6: Input2 - Video (OnBoard - Int.VDD)
PW392-AFE MDL <10bits>
Black Level Acq. Area H Start
Black Level Acq. Area V Start
White Level Acq. Area H Start
White Level Acq. Area V Start
Black/White Level Area Width
Black/White Level Area Height
Black Level Adj target
Black Level Adj telerance
White Level Adj target
White Level Adj telerance
Acq. Image Level Adj Tolerance
Y Image Area H Start
Y Image Area V Start
Image Level Acq. Width
Image Level Acq. Height
Y Level Adj target
Level Adj Tolerance
Acq. Image Level Adj Tolerance
PW392-AFE MDL <10bits>
Y - Offset Acq Area H Start
Y - Offset Acq Area V Start
CB - Offset Acq. Area H Start
CB - Offset Acq. Area V Start
CR - Offset Acq. Area H Start
CR - Offset Acq. Area V Start
Y
YCBCR Level Acq. Width
YCBCR Level Acq. Height
OFFSET Adj Tolerance
GAIN Adj Tolerance
Acq. Image Level Adj Tolerance
Auto PC Operation with the un-supported signal in.
0: Enable 1: Disable
TotalDot Search Step
TotalDot Match
Phase after Total Dot Adj.
0: Fine Phase Execute 1: Fine Phase Not Execute
Black Level Detect Area
Phase Detect Filter
0: All Bits Enable, 1: Lower 1 bit Disable, 2: Lower 2 bit Disable, 3:
Lower 3 bits Disable
Closed Caption On/Off at PIP mode
Range
1 - 20
1 - 255
1 - 255
0 - 6
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 1023
1 - 1023
0 - 1023
1 - 1023
1 - 255
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 1023
1 - 255
1 - 255
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 1023
1 - 255
1 - 255
1 - 255
0 - 1
0-3
0 - 10
0 - 1
0 - 7
0 - 3
0 - 1
-56-
Initial Note
3
4
20
0
975
500
25
500
13
9
20
1
940
1
4
10
200
8
9
808
1
4
925
500
925
500
925
500
50
500
800
500
700
500
13
9
4
512
512
808
892
892
1
1
4
0
1
5
1
1
0
1