Advertisement
®
We are delighted that you have chosen the InSinkErator
to be a part of your home. This unique appliance will save you time and effort in the
kitchen, and you'll enjoy discovering new uses for it each day. That's exactly why
millions of people are now using an InSinkErator Instant Hot Water Dispenser.
We are confident that by following our step-by-step instructions, you'll soon be enjoying
the convenience of instant hot water.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
■
For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing
or using this instant hot water dispenser.
■
This particular unit is not intended for commercial use.
■
Make sure that all electrical wiring and connections conform to local codes.
■
A standard 120-volt grounded electrical outlet is required under the sink for the dispenser's electrical power.
■
The wall outlet powering your dispenser must have power supplied to it continuously.
■
This outlet must be fused and should not be controlled by the same wall switch that operates the
disposer, unless you have a SinkTop Switch
■
It is recommended that a dedicated control valve be installed on the cold water line supplying water
to this system.
■
If you suspect elevated levels of chlorine in your water, it is recommended to use our water
filtration system.
■
The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).
If it does, this will prevent your unit from operating properly.
■
Moving parts inside the tank causing a rattling noise is normal.
WHAT YOU NEED TO GET STARTED
Equipment Required:
■
Drill
■
T-fitting
■
Dedicated control valve
■
Adjustable wrench
Equipment You May Need:
■
Anchors for drywall
■
Hole saw
If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a
1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line. See Step 1-B.
If you need to cut a mounting hole in your stainless steel sink, you may need a 1
for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other
than stainless steel.
2
®
Instant Hot Water Dispenser
™
from InSinkErator
®
.
■
Phillips and flat blade screwdrivers
■
Pencil
■
Tape measure
■
Level
■
Basin wrench
■
Hole punch
⁄
" - 1
⁄
" hole saw made
1
1
4
2
Identify the model of your instant hot water dispenser and record it here:________________
HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS
HOW TO USE THIS INSTRUCTION MANUAL
These instructions are separated into main sections, indicated by numbers, and subsections,
indicated by capital letters. The manual is setup this way to allow you to take a break at any
point after completing a section or subsection without affecting the installation process.
What you'll see in the
INSTALLING THE FAUCET - View/Wave/HC3/GN3
instruction manual:
A
2
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
Provides a step-by-step narrative describing the installation step, with check boxes that
1
can be marked as you progress through the installation.
2
Contains simple illustrations that provide visual instruction to support the narrative.
3
CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.
An imminently hazardous situation, which, if not avoided, will result in death or serious injury.
A potentially hazardous situation, which, if not avoided, could result in death or serious injury.
A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
OVERVIEW OF A
COMPLETED SETUP
HC3-SS
GN3-SS
H990-SS
H770-SS
View / Wave / HC3 / GN3
Unpack dispenser components.
On a firm, flat surface, carefully
straighten the copper tubing.
Remove the wing nut from
3
1
the valve body.
3
Advertisement
