Ddc Instructions - Philips 150X3M Service Manual

General
DDC Data Re-programming
In case the DDC data memory IC or main EEPROM which storage all
factory settings were replaced due to a defect, the serial numbers have
to be re-programmed.
It is advised to re-soldered DDC IC and main EEPROM from the old
board onto the new board if circuit board have been replaced, in this
case the DDC data does not need to be re-programmed.
Additional information
Additional information about DDC (Display Data Channel) may be
obtained from Video Electronics Standards Association (VESA).
Extended Display Identification Data(EDID) information may be also
obtained from VESA.
DDC EDID structure
For Analog interface: Standard Version 3.0
Structure Version 1.2
For Digital inferface: Standard Version 3.0
Structure Version 1.3
System and equipment requirements
1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98.
3. EDID301.EXE program (3138 106 10103) as shown in Fig. 1
4. A/D Alignment kits (3138 106 10079):
inclusion : a. Alignment box x1 (as Fig. 2)
b. Printer cable x1
c. (D-Sub) to (D-Sub) cable x1
d. (DVI-D) to (D-Sub) cable x1 (as Fig. 3)
Note: The EDID301.EXE (Release Version 1.58 20000818)is a
windows-based program, which cannot be run in MS-DOS.
Fig. 1 Fig. 1
EDID301.EXE
Ver:1.58
Diskette with EDID301.EXE
To Printer
DC 8V~12V
Power
indicator
To Monitor
Video Card
A/D Alignment Kits - Analog connection A/D Alignment Kits - Analog connection
Note: The alignment box has already build-in a batteries socket for
using batteries (9V) as power source. Pull out the socket by
remove four screws at the rear of box. Please do not forget that
remove batteries after programming. The energy of batteries can
only drive circuits for a short period of time.

DDC Instructions

Fig. 2
Fig. 3 Fig. 3
(DVI-D) to (D-Sub) cable
To Printer
DC 8V~12V
Power
indicator
To Monitor
(Digital port)
A/D Alignment Kits - Digital connection A/D Alignment Kits - Digital connection
Pin assignment
1
A. 15-pin D-Sub Connector 6
11
Pin No. Assignment
1
Red video input
Green video input
2
Blue video input
3
4 Ground
5 No Connected
6 Red video ground
Green video ground
7
8 Blue video ground
B. DVI-D Connector
1
9
17
Pin No. Assignment
1 TMDS Data 2-
2 TMDS Data 2+
3 TMDS Data 2/4 Shield
4 TMDS Data 4-
5 TMDS Data 4+
6 DDC Clock
7 DDC Data
8 No connect
9 TMDS Data 1-
10 TMDS Data 1+
11 TMDS Data 1/3 Shield
12 TMDS Data 3-
Configuration and procedure
There are threeips contained serial number on the circuit board,
Analog DDC IC, Digital DDC IC and main EEPROM which
storage all factory settings. Following descriptions are the
connection and procedure for Analog DDC IC and Digital DDC
IC, the main EEPROM can be re-programmed along with
Analog IC by enable factory memory data write function on the
DDC program (EDID301.EXE).
Initialize alignment box
In order to avoid that monitor entering power saving mode due to
sync will cut off by alignment box, it is necessary to initialize
alignment box before running programming software (EDID301.EXE).
Following steps show you the procedures and connection.
23
150X3M LCD
Go to cover page
5
10
15
Pin No. Assignment
9
+5V
10 Ground
11 Ground
12
Serial data line(SDA)
H.Sync
13
14 V.Sync(VCLK for DDC)
15
Data clock line(SCL)
8
16
24
Pin No. Assignment
13 TMDS Data 3+
14 +5V Power
15 Ground (+5V)
16 Hot Plug Detect
17 TMDS Data 0-
18 TMDS Data 0+
19 TMDS Data 0/5 Shield
20 TMDS Data 5-
21 TMDS Data 5+
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock-