Related Manuals for AMT Datasouth M7 SERIES
Summary of Contents for AMT Datasouth M7 SERIES
-
Page 1: Part List
M7 SERIES Thermal Printer Service Manua 4. PART LIST 4.1 Main Printer Assemblies... - Page 2 M7 SERIES Thermal Printer Service Manua Part No. Description Remark Spare Requirement 120732 Electronics cover 1 pc Mainframe 1 pc 120733 Cover, front 1 pc 120734 Top right side cover 1 pc 120735 Cover, rear 1 pc 30-0240016-00LF Media view window...
-
Page 3: Lcd Panel Assembly
M7 SERIES Thermal Printer Service Manua 4.2 LCD Panel Assembly Spare Part No. Description Remark Requirement 120747 Panel plate 1 pc 120748 Panel cover 1 pc 120749 Keypad 1 pc 120750 LCD panel board assembly 1 pc 120751 Screw, TP3*8... - Page 4 M7 SERIES Thermal Printer Service Manua 4.3 Print Engine Lower Mechanism Assembly Spare Part No. Description Remark Requirement 1 37-1502510-34LF Screw, M2.5*10 2 pcs 2 30-0240032-00LF Print head release lever (Left) 1 pc 3 32-0240032-00LF Spring torsion 1 pc 4 37-1503006-G4LF Screw, M3*6...
- Page 5 M7 SERIES Thermal Printer Service Manua 4.4 Ribbon Rewind Spindle Assembly Spare Part No. Description Remark Requirement 1 37-3410200-02LF E-ring, ID10*OD20*T0.6mm 2 pcs 2 32-0240036-00LF Bearing 1 pc 3 32-0240014-00LF Spring 1 pc 120753 Gear 1 pc 5 32-0240037-00LF Bearing...
- Page 6 M7 SERIES Thermal Printer Service Manua 4.5 Ribbon Supply Spindle Assembly & Damper Assembly Spare Part No. Description Remark Requirement 1 32-0240012-00LF Ribbon supply spindle shaft 1 pc 32-0240011-00LF Spring, ribbon supply spindle 2 pcs 3 98-0240059-00LF Ribbon supply spindle front cover...
- Page 7 M7 SERIES Thermal Printer Service Manua 4.6 Electronics Maintenance Kit & Drive System Spare Part No. Description Remark Requirement 120754 Power supply unit (M7 PLUS) 1 set 120755 Power supply unit (M7) 120806 Multi-interface board 1 set (Dealer option for M7)
-
Page 8: Option And Accessories
M7 SERIES Thermal Printer Service Manua 4.7 Option and Accessories... - Page 9 M7 SERIES Thermal Printer Service Manua Spare Part No. Description Remark Requirement 120761 Power cord / US Standard 72-0050007-00LF Power cord / EU Option 72-0050007-10LF Power cord / EU 90 degree Option 72-0050010-10LF Power cord / UK Option 72-0050011-10LF Power cord / AU...
-
Page 10: Troubleshooting
M7 SERIES Thermal Printer Service Manua 5. TROUBLESHOOTING 5.1 Common Problems The following guide lists the most common problems that might be encountered when operating this bar code printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service Department of your purchased reseller or distributor for assistance. - Page 11 M7 SERIES Thermal Printer Service Manua * If the cutter module is installed, press the UP or DOWN key to rotate the cutter knife back to the * Cutter jam. start position. Fwd. * There is no cutter installed on the * Remove the label.
- Page 12 M7 SERIES Thermal Printer Service Manua * Use the supported capacity SD card. * Insert the SD card again. * The supported SD card spec. - 128MB * SD card is damaged. SD card is unable to - 256MB * SD card doesn’t insert correctly.
- Page 13 M7 SERIES Thermal Printer Service Manua LCD panel is dark and * The cable between main PCB and LCD * Check if the cable between main PCB and LCD keys are not working. panel is loose. is secured or not.
- Page 14 M7 SERIES Thermal Printer Service Manua * Calibrate the sensor sensitivity again. * Set the correct label size and gap size. * Press [MENU] [SELECT] x3 [DOWN] x6 [SELECT] to fine-tune the parameter of Shift Y. * If using the software BarTender, adjust the vertical offset in the driver.
-
Page 15: Mechanism Fine Adjustment To Avoid Ribbon Wrinkles
M7 SERIES Thermal Printer Service Manua 5.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles This printer has been fully tested before delivery. There should not be ribbon wrinkle presented on the printed media for general-purpose applications. Ribbon wrinkle is related to the media thickness, print head pressure, balance, ribbon film characteristics, print darkness setting…etc. - Page 16 M7 SERIES Thermal Printer Service Manua Adjust the print head pressure adjustment knob Adjust the print head pressure adjustment knob Left knob Right knob Right knob Left knob The print head pressure adjustment knob has 5 The print head pressure adjustment knob has 5 levels of settings.
-
Page 17: Maintenance
M7 SERIES Thermal Printer Service Manua 6. MAINTENANCE This section pertains to the cleaning tools and methods used to maintain your printer. 1. Use one of following materials to clean the printer. Cotton swab (Head cleaner pen) Lint-free cloth Vacuum / Blower brush... - Page 18 M7 SERIES Thermal Printer Service Manua 1. Turn the power off. Clean the platen roller when changing a 2. Rotate the platen roller and new label roll Platen Roller wipe it thoroughly with 100% ethanol and a cotton swab, or lint-free cloth.
-
Page 19: Update History
M7 SERIES Thermal Printer Service Manua UPDATE HISTORY Date Content Editor 1 JUN 09 Production Release AMT DATASOUTH CORPORATION 5033 Sirona Drive, Suit #800 Charlotte, NC 28273 704-523-8500...