Turning Off The Power With The Sleep Timer - JVC RX-D401S Instructions Manual

Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
ANALOG
AUTO SURR
L R
S.WFR
10min 20min 30min 40min 50min 60min
OFF (canceled)
90min
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly so that "SLEEP OFF" appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when you turn off the
receiver.
SLEEP indicator
SLEEP
80min 70min
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Audio input setting (see pages 16 and 17)
• Midnight mode (see page 25)
• Volume level for each source when One Touch Operation is
< >
set to "ONETOUCH ON " (see page 26)
• Speaker output level (see page 28)
• Digital equalization pattern (see page 28)
• Bass boost (see page 29)
• Input attenuator mode (see page 29)
• Surround/DSP mode selection (see page 37)
NOTE
If the source is "FM" or "AM," you can assign a different setting
for each band.
Signal and speaker indicators on the display
Signal indicators
L C R
S.WFR LFE
ANALOG DUAL MONO
DIGITAL AUTO
L
LS S RS
LINEAR PCM
S.WFR
DIGITAL
LS
SB SB SB
96 / 24
SB SB
The signal indicators light up as follows:
L: • When digital input is selected: Lights up when the
left channel signal comes in.
• When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the
right channel signal comes in.
• When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS: Lights up when the left surround channel signal comes
in.
RS: Lights up when the right surround channel signal comes
in.
S: Lights up when monaural surround signal comes in.
SB: Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
NOTES
• When "A MULTI" is selected in "AUDIO INPUT" setting (see
pages 16 and 17), all the signal indicators except "SB," "S,"
and "LFE" light up.
• When playing back multi-channel digital sound recorded in
DVD-Audio with HDMI connection (see pages 9, 16, and
17), the signal indicators may not light up correctly.
The speaker indicators light up as follows:
• The subwoofer indicator (
S.WFR
"SUBWOOFER" is set to "SUBWFR
see page 22.
• The other speaker indicators light up only when the
corresponding speaker is set to "SML (small)" or "LRG
(large)," and also when required for the current playback.
Speaker indicators
L C R
S.WFR LFE
AUTO SURR
R
C HEADPHONE
LS S RS
PL x
LFE
NEO : 6 DSP
S RS
3D-PHONIC
SB SB SB
SB
VIRTUAL SB
) lights up when
< >
YES ." For details,
19