Turning Off The Sounds Temporarily; Changing The Display Brightness; Turning Off The Power With The Sleep Timer - JVC RXD212B - 110 Watts X 7 Receiver Instructions Manual

Turning off the sounds temporarily

From the remote control ONLY:
Press MUTING to turn off the sound through all
connected speakers and headphones.
"MUTING" appears on the display and the volume turns off.
ANALOG
AUTO SURR
L R
S.WFR
To restore the sound, press MUTING again.
• Pressing VOLUME +/– (or turning MASTER VOLUME control
on the front panel) also restores the sound.

Changing the display brightness

You can dim the display—Dimmer.
Press DIMMER repeatedly.
• Each time you press the button, the display brightness changes
as follows:
DIMMER 1: Dims the display.
DIMMER 2: Dims the display more than DIMMER 1.
DIMMER 3: Turns off the display.
(Temporarily canceled when you operate the
receiver.)
DIMMER OFF: Cancels the Dimmer (normal display).
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
ANALOG
AUTO SURR
L R
S.WFR
10min 20min 30min 40min 50min 60min
OFF (canceled)
90min
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly so that "SLEEP OFF" appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when you turn off the
receiver.
14
SLEEP indicator
SLEEP
80min 70min
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see page 12)
• Bass boost (see page 28)
• Digital equalization pattern (see page 27)
• Input attenuator mode (see page 28)
• Midnight mode (see page 24)
• Speaker output level (see page 27)
• Surround/DSP mode selection (see page 34)
NOTE
If the source is "FM" or "AM," you can assign a different setting
for each band.
Signal and speaker indicators on the display
Signal indicators
L C R
S.WFR LFE
ANALOG DUAL MONO
DIGITAL AUTO
L C
LS S RS
LINEAR PCM
S.WFR
DIGITAL
LS S
SB SB SB
96 / 24
SB SB
The signal indicators light up as follows:
L: • When digital input is selected: Lights up when the
left channel signal comes in.
• When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the
right channel signal comes in.
• When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS: Lights up when the left surround channel signal comes
in.
RS: Lights up when the right surround channel signal comes
in.
S: Lights up when monaural surround signal comes in.
SB: Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
The speaker indicators light up as follows:
• The subwoofer indicator (
S.WFR
"SUBWOOFER" is set to "SUBWFR
see page 22.
• The other speaker indicators light up only when the
corresponding speaker is set to "SML (small)" or "LRG
(large)," and also when required for the current playback.
Speaker indicators
L C R
S.WFR LFE
AUTO SURR
R HEADPHONE
LS S RS
PL x
LFE
NEO : 6 DSP
RS
3D-PHONIC
SB SB SB
SB
VIRTUAL SB
) lights up when
< >
YES ." For details,