Table of Contents
Advertisement
• When using the optional stay
!"#
•
•
Fire wall
Washer
Dashboard
Sleeve
!
Less than 30°
30°
30
Removing the unit
• Before removing the unit, release the rear section.
1
Remove the control panel.
2
Remove the trim plate.
3
Insert the 2 handles into the slots, as shown.
Then, while gently pulling the handles away from
each other, slide out the unit. (Be sure to keep
the handles after installing it.)
1
Control panel
!
Parts list for installation and
connection
The following parts are provided with this unit.
After checking them, please set them correctly.
Hard case/Control panel
!"#$
Handles
!"
Rubber cushion
!"
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you
disconnect the battery's negative terminal and make
all electrical connections before installing the unit. If
you are not sure how to install this unit correctly, have
it installed by a qualified technician.
Note:
This unit is designed to operate only on 12 V DC,
NEGATIVE ground electrical systems. If your vehicle
does not have this system, a voltage inverter is required,
which can be purchased at JVC car audio dealers.
• Replace the fuse with one of the specified rating. If
the fuse blows frequently, consult your JVC car audio
dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power circuit.
However, with some vehicles, clicking or other
unwanted noise may occur. If this happens, connect
the unit's rear ground terminal (see connection
diagram) to the car's chassis using shorter and
thicker cords, such as copper braiding or gauge wire.
If noise still persists, consult your JVC car audio dealer.
• Maximum input of the speakers should be more
than 50 W at the rear and 50 W at the front, with an
impedance of 4 Ω to 8 Ω.
• Be sure to ground this unit to the car's chassis.
• The heat sink becomes very hot after use. Be
careful not to touch it when removing this unit.
Heat sink
• When installing the unit without using the sleeve
•
•
•
Stay (option)
In a Toyota for example, first remove the car radio and install the unit in its place.
!"
Lock nut
!
Screw (option)
!"#$%
Mounting bolt
!
Note: When installing the unit on the mounting brackets, make sure to use the 6 mm-long screws. If longer screws are used, they could
damage the unit.
Install the unit at an angle of less
than 30°
!"#$% 30°
!
30
!
!"#$%&!"'()*+,-.(/01
•
1
!"#$
2
!"#
3
!"#$%&'()*+,-."/012
!"#$ %&'()*+,$-.
!"#$%&'()*+,
2
Trim plate
!"#$%&'(
!"#$%&'()
!"#$%&'()*
Sleeve
!
Mounting bolt (M5 x 20 mm)
!=EM5 x 20 mmF
M5 x 20
x M5
Washer (ø5)
Lock nut (M5)
!=EM5F
=Eø5F
ø5
M5
M5
!
!"#$%&'()*+,#-./012
!"#$%&'()*+,-./01+23
!"#$%&'()*+,-. !/
!"#$% 12V
!"#$%&'
!"#$%&'()*+,$-%./01)2
!"#$%&'(
JVC
!"#$%&'()*
•
!"# JVC
!"#$%&'
!"#$KKK
•
!"#$%&'()*+,-./01 23
!"#$%%&'()*+,-./0123
!"#$%&'()*+,-%./ 012
!"#$%&'(
!"#$%&'()*+,- JVC
!"
! "#$%&'()*+,'- 50 W
•
4 Ω – 8 Ω
!"#$%&'()*+,-
•
!"#$%&'(%)*+#,-.
•
!"#$%&'
!"#$%&'($
!"TOYOTA
!"#$%
!"#$%&'()$*+,- ./01
Flat type screws (M5 x 6 mm)*
!"EM5 x 6 mmF*
M5 x 6
*
Bracket*
*
*
x
M5
*
Pocket
!"#$%&'()*+, 6mm
•
1
2
3
2
Trim plate
Battery
CR2025
Remote controller
!
!+,-
!.
•
•
!"
!"#$
!"
•
/#
•
•
2
•
*
Flat type screws (M5 x 6 mm)*
Bracket*
*
*
*
*
!"#$%&'
!"()*+,-#
6
3
Handles
!"
Power cord
Only for KD-LH3105 /
KD-LH3105
KD-LH3105/
CD-ROM—Image converter
!"
CD-ROM—
CD-ROM
12
JVC
JVC
JVC
50
50
4 Ω – 8 Ω
* Not included with this unit.
!"#$
*
*
*
!"EM5 x 6 mmF*
M5 x 6
*
x
M5
•
!"#$%&
=KD-LH3105 /
DC
JVC
•
JVC
•
JVC
•
•
•
Advertisement
Table of Contents
