Zoo Fans H30 Installation Manual
Hide thumbs
Also See for H30:
- Installation manual (12 pages) ,
- Operating manual (6 pages) ,
- Operating manual (8 pages)
Related Manuals for Zoo Fans H30
Summary of Contents for Zoo Fans H30
- Page 1 Installation Guide Models: H30 / H60 Covered by the following United States Patent: D631,148S zoofans.com ZOO Fans is a Trade Mark of Zoo Fans Incorporated...
-
Page 2: Important Safety Information
WARNING: To prevent electrical shock and/or injury disconnect fan from power source before you move or service the fan. Suitable for use with solid-state speed controls. WARNING: To reduce the risk of fire, electric shock, and injury to persons, ZOO Fans must be installed only with controllers supplied by ZOO Fans. Other parts cannot be substituted. - Page 3 AVERTISSEMENT : Restez vigilent, faites attention à ce que vous faites, et faites preuve de bon sens lors de l’installation de ventilateurs ZOO Fans. N’installez pas de ventilateurs si vous êtes fatigué ou sous l’influence de drogues, d’alcool ou de médicaments.
-
Page 4: Table Of Contents
STEP 1: Fasten Main Hanging Gripple ..........................3 STEP 2: Fasten Stabilization Tether ............................4 STEP 3: Secure the Gripples ..............................5 WIRING THE FAN ..................................7 WIRING THE CONTROLLER ..............................8 zoofans.com ZOO Fans is a Trade Mark of Zoo Fans Incorporated... -
Page 5: Pre-Installation
PRE-INSTALLATION The safe installation and operation of equipment supplied by ZOO Fans is the responsibility of the system designer, installer, maintainer, and operator (collectively, the “User”). The need for protective safety accessories to meet company standards, applicable codes, and the requirements of the Occupational Safety and Health Act (“OSHA”) must be determined by the User since safety requirements may vary depending on the location and application of the equipment. -
Page 6: Zoo Fans Specifications
You may also contact your ZOO Fans’ representative or ZOO Fans directly if you require assistance. Remember, the number of ZOO Fans required for the job, as well as where they are hung, will depend on a number of variables, some of which are: •... -
Page 7: Installation
12” from any obstruction. ZOO Fans are designed to be hung vertically or at an angle. For vertical installations, proceed to STEP 1 below. To install your ZOO Fan at an angle, additional hardware is required. Please contact ZOO Fans or your ZOO Fans’ representative. -
Page 8: Step 2: Fasten Stabilization Tether
1. Insert 1/4” Hex Head bolt through the Eyelet of Gripple 2. Insert 1/4” Hex Head bolt through the hole located at 45° on either side of the handle 3. Securely tighten 1/4” Nylock Nut Illustration 2 zoofans.com Page 4 ZOO Fans is a Trade Mark of Zoo Fans Incorporated... -
Page 9: Step 3: Secure The Gripples
1. Insert wire through Gripple 2. Loop wire over Truss, I-Beam, or support beam 3. Insert end of wire into Gripple 4. Adjust to desired height Illustration 3 zoofans.com Page 5 ZOO Fans is a Trade Mark of Zoo Fans Incorporated... - Page 10 2. At a 45 ° angle, loop wire over Truss, I-beam, or support beam 3. Push end of wire into Gripple 4. Adjust wire so there is no slack Illustration 4 zoofans.com Page 6 ZOO Fans is a Trade Mark of Zoo Fans Incorporated...
-
Page 11: Wiring The Fan
Electrical connection should be made according to the wiring diagram (See Illustration 5). • All safety features (surge suppression diode AND motor run capacitor) must remain installed. Illustration 5 zoofans.com Page 7 ZOO Fans is a Trade Mark of Zoo Fans Incorporated... -
Page 12: Wiring The Controller
Mount the controller so that the fan it controls is visible from the controller. • To control multiple fans with one controller, please contact ZOO Fans. • Ground wire must be bonded at each location where metal boxes are used. - Page 14 1650 38 St. Suite 201W Boulder, CO 80301 303.557.1852 zoofans.com...
Need help?
Do you have a question about the H30 and is the answer not in the manual?
Questions and answers