Drive Manual Operation - Sony DVP-PQ2 Service Manual

QQ
3 7 63 1515 0

6-5. DRIVE MANUAL OPERATION

On the Test Mode Menu screen, select
tion menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc type
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
0. Disc Check Memory
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
screen.
2. After power ON, if the Drive Manual Operation was se-
lected, first perform "Reset SLED TILT" by opening 1.
Disc Type screen.
3. In case of an alarm, immediately press the
stop the servo operation, and turn the power OFF.
TE
L 13942296513
Basic operation (controllable from front panel or remote com-
mander)
[I/ ]
1
x
[ RETURN]
O
,
> .
[1] to [9], [0]
Cursor [Q]/[q]
www
.
http://www.xiaoyu163.com
[2]
, and the manual opera-
Exit: RETURN
x
Power OFF
Servo stop
Return to Operation Menu or Test Mode
Menu
Transition between sub modes of menu
Selection of menu items
Increase/Decrease in manually adjusted
value
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
0. Disc Check Memory
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
On this screen, the mirror time is measured and written to the
EEPROM to check the disc type. First, set a DVD SL disc and
[1]
press , then set a CD disc and press
DL disc and press
spectively.
The adjustment must be executed more than once after default
data were written.
From this screen, you can go to another mode by pressing
key, but you cannot enter this mode from another mode.
.
You can enter this mode from the Operation Menu screen only.
1. Disc Type
Disc Type
button to
1. Disc Type Auto Check
Q Q
2. DVD SL
3 6 7 1 3
3. DVD DL
4. CD
5. SACD
6. DVD SL
7. DVD DL
8. CD
9. LCD
0. Reset SLED TILT
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
disc type. In case of wrong display, retry "Disc Check Memory".
Also, opening the lid causes the set disc type to be cleared. In this
case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
1. Disc Type Auto Check
2. DVD SL
3. DVD DL
4. CD
5. SACD
6. DVD SL
7. DVD DL
8. CD
9. LCD
0. Reset SLED TILT
SA.------ SI.-- EMG.00
DVD SL 12cm
.
Display when DVD SL 12cm disc was selected
6-7
9 4 2 8
Disc Check
[2]
, and finally set a DVD
[3]
. The measured mirror time is displayed re-
Disc Type
12cm
1 5 0 5 8 2 9 9 4
12cm
12cm
12cm
8cm
8cm
8cm
8cm
EMG. 00
[1]
automatically selects and displays the
Disc Type
12cm
12cm
12cm
12cm
8cm
8cm
m
8cm
8cm
co
9 9
or
>
2 8 9 9