Drive Manual Operation; Drive Manual Operation Menu Screen; Disc Type; Manual Control 1 - Sony DVP-C600D Service Manual
Hide thumbs
Also See for DVP-C600D:
- Operating instructions manual (59 pages) ,
- Training manual (108 pages) ,
- Service manual (26 pages)
Table of Contents
Advertisement
6-6. Drive Manual Operation
In performing manual operation, observe the following points:
Select correct disc type on the Disc Type screen.
First, select “0. Disc TYpe” and execute “7. Hydet init” and “8.
Sled init”. (See Figure 12)
In case of abnormality, press [STOP] immediately to stop opera-
tion and turn off the power.
Do not execute Auto Adjust while executing FG Pause.
Also, as these commands are not protected, take care not to press
wrong key.
When PLL is locked, the sector address (or time code) is displayed
on the right side of SA.
6-6-1. Drive Manual Operation Menu Screen
Drive Manual Operation
SA.000000
SI.00
EMG.00
0. Disc Type
1. Manual Control 1
2. Manual Control 2
3. Manual Control 3
4. Manual Adjust 1
5. Manual Adjust 2
6. Auto Adjust
7. Check
Figure 11
This screen provides a menu for manual operation, and you can go
directly to each screen from here. To return to this screen from
each screen, press the RETURN key.
If [SET UP] button is pressed, the screen returns to the Test Mode
menu.
For switching between respective screens, use the [CLEAR] key.
After this menu is started, initializing is performed and chucking
Disc1 is started.
6-6-2. Disc Type
Disk type
SA.000000
SI.00
EMG.00
0. DVD SL
12cm
9. Home
1. CD
12cm
2. DVD DL
12cm
3. DVD SL
8cm
4. CD
8cm
5. DVD DL
8cm
6. Disc type check
7. Hydet init
8. Sled init.
DVD SL
12cm
Figure 12
On this screen, select the type of disc used.
“6. Disc type check” judges the disc loaded. Confirm that judg-
ment result meets the loaded disc type.
Judgment may fail if adjustment is not made yet immediately af-
ter EEPROM Default Set. The CD which is not cut up to the CD
detection sensor position is judged as DVD. The optical system
will be damaged if other disc is loaded after selecting DVD DL.
Be sure to set the disc type.
6-6-3. Manual Control 1
Manual Control 1
SA.000000
SI.00
EMG.00
0. LD
off
7. CLVA
1. SP
off
8. CAV
2. Tilt
off
9. Home
→. Sled FWD
3. Focus
off
←. Sled RVS
4. Track
off
↑ . Tilt Up
5. Sled
off
↓ . Tilt Down
6. AGC
off
DVD SL
12cm
Figure 13
On this screen, turn on/off servo operation items necessary for
playing.
Normally, turn on the items from 0 sequentially, and normal trace
is executed at CLVA. In the tracking status, the sector address (or
time code (at CD)) is displayed.
If not displayed, the spindle is not locked, which means a failure.
In case of spindle system failure or no RF, the spindle system may
run, overriding the control.
In this case, do not press the CLVA.
0. LD
: Turn on/off the laser diode.
1. SP
: Turn on/off the spindle.
At SP ON, the spindle runs in constant velocity mode.
2. TILT : Turn on/off the tilt servo.
3. Focus : Focus searching is executed and focus is turned on.
Operation is terminated if focus is not turned on after
focus search is retried about 3 times.
4. Track : Turn on/off the tracking servo.
5. Sled : Turn on/off the sled servo.
6. AGC : Turns on/off the focus error auto gain control by PULL
IN level.
7. CLVA : Spindle normal servo.
8. CAV : Spindle in constant velocity mode
9. Home : Return to home position.
→.
: Move the sled system outside.
Perform this with the tracking turned off.
←.
: Move the sled system inside.
Perform this with the tracking turned off.
↑ .
: Move the tilt system up.
↓ .
: Move the tilt system down.
6-14
- Quick Links:
- Table of Contents
- General
Hide quick links:
Advertisement
Table of Contents
