Advertisement
Quick Links
AUTO OFF:
This unit comes with an auto-off feature to conserve battery power.
The scale will automatically turn off after approximately four minutes of
inactivity.
CAUTION:
Do not place more than the capacity of the scale on the weighing platform.
Abuse of this type can cause damage to the scale and void the warranty.
This scale is a sensitive electronic instrument. Avoid vibrations, strong
electrical or magnetic fields, and rapid changes in humidity or temperature
as they can adversely affect accuracy.
CARE AND MAINTENANCE:
• Avoid lengthy exposure to extreme heat or cold. To achieve optimum
functioning, allow this unit to acclimatize.
• Allow scale a minimum of thirty seconds to warm up before calibration to
allow internal components to stabilize.
• Keep this product clean. Dust, dirt, and moisture can adversely affect the
reliability and accuracy of this scale.
• Vibrations, air currents and proximity to other electronic equipment may
affect accuracy of this product. Avoid disturbing the environmental conditions
when weighing. Be sure weighing is done with scale on a flat surface in a
sheltered area.
• Handle with care. Although this product is durable, rough treatment may
permanently damage the internal sensor.
Hornady Electronic Scale
Instruction Manual
Model GS-
Congratulations on your selection of a quality Hornady product.
With proper care and use, this product will provide years of
dependable service. Hornady is committed to providing products
that fit your needs, manufactured to the highest of quality standards.
If you have any comments or suggestions concerning this product
please mail them to:
Hornady Manufacturing
P.O. Box 1848
Grand Island, NE 68802-1848 USA
www.hornady.com
Please read all the operating instructions to ensure the best performance
from your Hornady Electronic Scale.
CAPACITY/ACCURACY:
1000grain/65grams x 0.1grain/0.01gram
POWER SOURCE:
Four "AA" alkaline batteries or 120 Volt AC adapter
(output DC 6V 100mA)
BATTERY INSERTION:
1.
Turn scale upside down and locate battery compartment cover.
2
. Push tab toward compartment cover. Lift cover off.
3.
Insert four "AA" alkaline batteries; ensure that battery polarities
are aligned properly.
4.
Replace battery compartment cover and secure.
5.
The scale is now ready for use.
Note: Do not use excessive force in removing or replacing battery
compartment cover.
1000
Advertisement
Related Manuals for Hornady GS-1000
Summary of Contents for Hornady GS-1000
- Page 1 Model GS- inactivity. CAUTION: Congratulations on your selection of a quality Hornady product. Do not place more than the capacity of the scale on the weighing platform. With proper care and use, this product will provide years of Abuse of this type can cause damage to the scale and void the warranty.
- Page 2 KEY PAD FUNCTIONS: OPERATION: ON/OFF/ZERO Key: Place scale on a flat surface in a sheltered area. ON/OFF/ZERO Press and hold the button to turn the scale on. Press and hold to turn unit on or off. Open platform lid and place tray on weighing platform. (You may also Once unit is on, this key operates the tare function.
Need help?
Do you have a question about the GS-1000 and is the answer not in the manual?
Questions and answers
I have GS 1000 electronic scale from Hornady which I have very seldom used, now when I wanted to use it again it gives me a fault code. Please see attached picture. Can you please help me to get it work again.
If your Hornady GS-1000 electronic scale displays a fault code, follow these steps to troubleshoot:
1. Overload Error ("E" on Display)
- Remove any excessive weight immediately.
- Ensure the load does not exceed the scale’s maximum capacity (1000 grains or 65 grams).
- If the error persists, check for possible damage.
2. Calibration Error ("CAL E" on Display)
- Retry the calibration process.
- Ensure the correct calibration weight is used.
- Place the weight gently in the center of the weighing tray.
- Avoid vibrations, air currents, or unstable environmental conditions.
3. General Troubleshooting
- Ensure the scale is on a flat, stable surface.
- Keep it away from strong electrical or magnetic fields.
- Allow at least 30 seconds for warm-up before calibration.
- Check battery power or use a 120V AC adapter if necessary.
- Keep the scale clean and free from dust or moisture.
If errors persist, the scale may require professional inspection or repair.
This answer is automatically generated