Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SkyBell WiFi Video Doorbell
Summary of Contents for SkyBell WiFi Video Doorbell
- Page 1 WiFi Video Doorbell Installation & Starting Guide www.skybell.com...
- Page 2 110/120 VAC or 220/230/240 VAC power standard. SkyBell can only be attached to a low voltage transformer (8-36 VAC or 12 VDC) and not directly to primary power (110/120 VAC and 220/230/240 VAC).
- Page 3 Infrared LED (Night Vision) Camera Camera Positioning Hole Indicator Motion Sensor Button Microphone Speaker Set Screw Advanced Components Motion sensors detect a visitor. LED button tells you if SkyBell is disconnected from Wi-Fi. Infrared technology lets you see at night.
- Page 4 Contents SkyBell Mounting Plate Doorbell Device Special Locking Tool Wall Screws (4) Screw Anchors (4) Wire Connectors (2) Tools You May Need for Installation: Pliers or crimpers Power Drill or Screw Driver Outdoor Adhesive Wire Strippers...
-
Page 5: Installation Guide
Wi-Fi signal range at your door. To test, simply place your smartphone where you plan to install SkyBell. If you have a Wi-Fi connection on your phone, then SkyBell will also have Wi- Fi connection 99% of the time. - Page 6 Before moving to the next step, please confirm that your wires are not connected to high-voltage power. SkyBell can only be connected to a low-voltage transformer from 8-36 VAC or 12 VDC. 3. Remove existing doorbell and carefully detach or cut the 2 wires currently connected to your existing doorbell.
- Page 7 Instead of drilling the mounting plate into place, you may use an outdoor adhesive to glue the mounting plate into place. ** Caution: Do not connect SkyBell directly to high voltage wires (120/130V or 220/230/240V) from your primary power system. SkyBell...
- Page 8 7. Next, strip the ends of your home’s wires and the ends of the SkyBell wires. 8. Twist the ends of one SkyBell wire and one home doorbell wire as shown below. It does not matter which wires you use as long as you use one from the house and one from SkyBell.
- Page 9 SkyBell to either wire coming from your wall. 12. Turn your power back on. 13. Next, check SkyBell to confirm that the LED light is on. The device LED light will slowly blink red if the battery is charging.
- Page 10 This will lock the device. Do not over turn. Be sure that the screw is not exposed beyond the bottom of the device. 17. Your SkyBell device is now properly installed. Please allow the device’s battery to charge for 10-15 minutes before moving to Section 2 –...
-
Page 11: Skybell Cannot Connect To 5Ghz
2. Name of your Wi-Fi network 3. Wi-Fi network password (if necessary) 4. SkyBell Device ID Label Preparation 1. Before you get started, allow SkyBell to power up for 10 minutes. During this time the LED light should be red or slow blinking red. -
Page 12: The Syncing Process
You will need your SkyBell Device ID and Wi-Fi Password. Be sure to put the device into Sync Mode by hitting and holding the main SkyBell button until the LED light starts blinking. A. If the setup is successful: a. - Page 13 3. Once your setup is successful, it may take up to 15 minutes for the device to connect to the server and for your account to be created. 4. When the SkyBell LED is a solid green light, press the SkyBell device button...
- Page 14 Rotate the tool to position the camera with your finger and the security tool. 6. In the app, your new SkyBell device will appear in the home screen of the app. You can tap that device to adjust its individual settings.
- Page 15 SBT makes no commitment to provide any such changes, updates, enhancements or other additions to this document to you in a timely manner or at all. Visit the SkyBell Web site (www.skybell.com) for current updates and information concerning the use and operation of SBT Products.
- Page 16 SkyBell. Do not use or attempt to install your SkyBell if it has been damaged. Water and Wet Locations. Your SkyBell Wi- Fi video doorbell is weather resistant but not waterproof.
- Page 17 DISTANCE OF 20CM BETWEEN THE RADIATOR AND YOUR BODY. ALL CABLES USED TO CONNECT PERIPHERALS MUST BE SHIELDED AND GROUNDED. OPERATION WITH CABLES CONNECTED TO PERIPHERALS THAT ARE NOT SHIELDED AND GROUNDED MAY RESULT IN INTERFERENCE TO RADIO AND TELEVISION RECEPTION. SkyBell Limited Warranty...
- Page 18 Subject to the terms and conditions of this Limited Warranty, SBT, warrants to you only (the original purchaser), that under normal use, the SkyBell device (the “Product”) will substantially conform with the specifications listed on our website (www.skybell.com) and be free of reproducible defects that...
- Page 19 There is no warranty of any kind for any defects discovered after the Warranty Period has lapsed. After the Warranty Period has expired, SBT at its sole and complete discretion may offer you a replacement Product or repair of your Product in exchange for a fee to be determined at SBT’s discretion.
- Page 20 NEGLIGENCE OR OF WORKMANLIKE EFFORT); OR • (iii) INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF RELATING IN ANY WAY TO THE SKYBELL PRODUCT. SBT’S CUMULATIVE LIABILITY, WHETHER FOR BREACH OF CONTRACT, WARRANTY, NEGLIGENCE, STRICT LIABILITY IN TORT, INDEMNIFICATION, CONTRIBUTION,...
- Page 21 OR OTHERWISE, SHALL BE LIMITED TO THE DIRECT DAMAGES RECOVERABLE UNDER LAW, BUT NOT TO EXCEED THE PURCHASE PRICE FOR THE SKYBELL WI-FI VIDEO DOORBELL. YOU HEREBY RELEASE SBT, ITS MANUFACTURERS, SERVICE PROVIDERS, LICENSORS AND EACH OF THEIR RESPECTIVE AFFILIATES, FROM ANY AND ALL OBLIGATIONS, LIABILITIES, AND CLAIMS IN EXCESS OF THIS LIMITATION.
- Page 22 SYSTEM, SECURITY SYSTEM OR THEFT DETERRENT. SKYBELL MAKES NO CLAIM OR REPRESENTATION THAT IT WILL KEEP YOU OR YOUR PROPERTY SAFE FROM HARM. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
- Page 23 Warranty service or a refund of any kind. A list of authorized resellers is available on SBT’s website. To review the full warranty, visit www.skybell.com/legal. SkyBell and SkyBell Technologies, Inc. are trademarks SkyBell Technologies, Inc., registered in the U.S. and other countries.
- Page 24 SkyBell is a Wi-Fi enabled doorbell and is a trademark of SkyBell Technologies, Inc. The device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.