CONTENTS 1. PRECAUTIONS -----------------------------------------------------------------------------------------------------------------------2 1-1 S AFETY RECAUTIONS ------------------------------------------------------------------------------------------------------------2 1-2 S ERVICING RECAUTIONS --------------------------------------------------------------------------------------------------------3 1-2-1 General Serving Precautions ------------------------------------------------------------------------------------------------3 1-2-2 Insulation Checking Procedure ---------------------------------------------------------------------------------------------4 1-3 ESD P RECAUTIONS ---------------------------------------------------------------------------------------------------------------4 2. REFERENCE INFORMATION ----------------------------------------------------------------------------------------------------5 2-1 C OMPONENT ESCRIPTIONS -----------------------------------------------------------------------------------------------------5 2-1-1 DVD SONY HM-313 PUH----------------------------------------------------------------------------------------------------5 2-1-2 DVD Processor Chip MTK1389E ------------------------------------------------------------------------------------------7 2-1-3 Serial EEPROM, 2K (256 x 8) (24C02) or 16 K (2048 x 8) (24C16)------------------------------------------------ 23 ...
1. PRECAUTIONS 1-1 Safety Precautions 1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: (1) Be sure that no built-in protective devices are defective or have been defeated during servicing. (1) Protective shields are provided to protect both the technician and the customer.
Page 4
2) Read and comply with all caution and safety related 5) Components, parts, and/or wiring that appear to notes non or inside the cabinet, or on the chassis. have overheated or that are otherwise damaged should be replaced with components, parts and/or 3) Design Alteration Warning-Do not alter of add to the wiring that...
Page 5
1-2-2 Insulation Checking Procedure attachment plug and accessible conductive parts (see Disconnect the attachment plug from the AC outlet and note) should be more than 1 Megohm. turn the power ON. Connect the insulation resistance Note: Accessible conductive parts include metal meter (500V) to the blades of the attachment plug.
Page 6
2. Reference Information 2-1 Component Descriptions 2-1-1 DVD SONY HM 313 Connector Pin Definition - 5 -...
Block Diagram i s r 4 χ 6 1 t a l l i o l i o & f i l r e i ) l e - 6 -...
Page 8
2-1-2 DVD Processor Chip MTK1389E/F Features Super Integration DVD player single chip High performance analog RF amplifier Servo controller and data channel processing Disc compatibility: DVD, DVD-R, DVD-RW, DVD+R, DVD+RW, Audio CD, CD-R, CD-RW, VCD, SVCD, MP3-CD, MP3-DVD, PCM, JPEG-CD, JPEG-DVD Format compatibility:MPEG-1, MPEG-2, MPEG-4, DivX 3.11, DivX 4.x, DivX5.x (Need licence), Xvid, MP3, WMA, PCM, and JPEG &...
Page 9
Fun c t i o n a l B l oc k CVBS, Y/C Debug 108MHz Port Component Module TV Encoder Video RF Amplifier Video DAC Servo IO Motor Servo Video Drive Processor Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder...
2-1-3 Serial EEPROM, 2K (256 x 8) (24C02) or 16 K (2048 x 8) (24C16) 24C02 is used for DVD player while 24C16 is for DVD receiver. The capacity is the only difference between two kinds of serial EEPROM. Both of them use same package and have same pin configuration. * Features Low-Voltage and Standard-Voltage Operation -5.0 (V CC = 4.5V to 5.5V)
Page 25
to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices. The MBM29LV160TE/BE is programmed by executing the program command sequence.
Page 28
2-1-5 1M x 16 Bit x 4 Banks Synchronous DRAM M12L64164A FEATURES ORDERING INFORMATION JEDEC standard 3.3V power supply LVTTL compatible with multiplexed address 54 Pin TSOP (Type II) Four banks operation (400mil x 875mil ) MRS cycle with address key programs - CAS Latency (2 &...
Page 29
FUNCTIONAL BLOCK DIAGRAM Clock Generator Bank D Bank C Bank B Address Address Buffer Mode Bank A & Register Refresh Counter Sense Amplifier L(U)DQM Column Column Decoder Address Buffer & Refresh Counter Data Control Circuit PIN FUNCTION DESCRIPTION NAME INPUT FUNCTION System Clock Active on the positive going edge to sample all inputs Disables or enables device operation by masking or enabling all...
Page 30
ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE UNIT Voltage on any pin relative to V -1.0 ~ 4.6 Voltage on V supply relative to V -1.0 ~ 4.6 ° Storage temperature -55 ~ +150 Power dissipation Short circuit current Permanent device damage may occur if ABSOLUTE MAXIMUM RATING are exceeded. Note: Functional operation should be restricted to recommended operating condition.
Page 31
DC CHARACTERISTICS ° Recommended operating condition unless otherwise noted,TA = 0 to 70 VERSION PARAMETER SYMBOL TEST CONDITION UNIT NOTE ≥ t Burst Length = 1, t = 0 mA, Operating Current RC(min) (One Bank Active) tcc = tcc(min) ≤ , tcc = tcc(min) CC2P IL(max)
Page 32
3. Product S pecifications Power supply AC ~110V/220 60/50Hz Power consumption 150W Temperature -10~+40 Working Relative humidity 5%~90% environment TV System PAL/NTSC Frequency Reponse 1.5dB(20Hz~20KHz) Disc output S/N(A weight) 80dB( 1KHz Dynamic Range 70dB( 1KHz THD+NOISE 60dB(1KHz) Below the limit of apparatus measure WOW FLUTTER AM frequency Range 520KHz~1620KHz...
4. Upgrading System and Changing the Region Code MTK upgrade: 1. Name upgrade file as "MTK.BIN"(must be in big caps) 2. Record it in a CD-R/W (It can be enclosed a sub-directory which size is about 30M, and the file content can be letter or non used file.) disc Format: (advise to use the tool NERO burning ROM) Disc volume: MEDIATEK, ISO9660 LEVEL1, MODE1,not JOILET.
5. Operating Instruction Please refer to the User’s Manual for the operating instruction of the system. Maintenance & Troubleshooting How to handle discs Disc Compatibility Some discs have special To handle, clean and protect discs ● requirements for playing, with which this player Do not touch the playing side of a disc ●...
Page 35
Problems and Solutions If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the set yourself, as this would invalidate the guarantee.
7.Troubleshooting No power Insert the AC power plug securely into the power outlet. Make sure that the equipment is connected properly. No picture Make sure that the input setting for TV is Video (AV). No sound Make sure that the equipment is connected properly. Make sure that the input settings for the TV and stereo system are Distorted sound correct.
11.Wiring Diagram power and signal Control Stream Tuner Video out Audio out MIC pcb board Power and signal loader MPEG PCB board Signal Audio Output Power Power Front Panel - 54 -...