Page 1 MiniTT1 and FlexTT5 Manual PDF generated using the open source mwlib toolkit. See http://code.pediapress.com/ for more information. PDF generated at: Tue, 05 Aug 2014 18:09:32 PST...
Page 2: Minitt1 And Flextt5
TTL or manual flashes anywhere to illuminate the scene: Around corners, out-of-sight and in bright sunlight. The MiniTT1 and FlexTT5 are compatible with any PocketWizard radio for triggering manual flash or remote cameras. The Canon-specific MiniTT1 and FlexTT5 radios work within the Canon E-TTL II system.
Page 3 Information you should know before using your radios. Also referred to as "READ ME FIRST" information. Key Features Learn more about the key features of your MiniTT1 and FlexTT5. Additional information on features can also be found at PocketWizard.com MiniTT1 and FlexTT5 FAQ...
Page 4 Learn Mode Learn Mode is not required for normal operation of your radios, but if you are working away from the PocketWizard Utility and in conflict with another photographer on your channel, Learn Mode allows you to change channels in the field.
Page 5: Minitt1 And Flextt5 Key Features
Dedicated TTL Triggering Locking your MiniTT1 Transmitter into the hot shoe of a Canon or Nikon DSLR camera, and mounting flashes onto FlexTT5 Transceivers gives you full flash exposure control with the freedom and reliability of a PocketWizard radio.
Page 6: Rear Curtain Sync
- both of which can produce results never possible before. HyperSync works with both Speedlights and full size studio flash. All you need is a MiniTT1 or FlexTT5 on camera that has been tuned to your specific camera and flash via the PocketWizard Utility. While performance varies by the camera and flash equipment being used, HyperSync will get the maximum possible out of any set-up.
Page 7: Getting Started
Review the owner’s manuals for your camera and flash system. For most basic functions when using Canon or Nikon’s system with PocketWizard's, operation is identical. Important exceptions will be noted in this wiki. Turn Everything OFF All equipment should be turned OFF when making connections.
Page 8: First Shot
MiniTT1 or FlexTT5 and sitting on an active camera. For example, you cannot take a 580EX II out of <MASTER> mode if the flash is in the hot shoe of a powered on remote FlexTT5. Turn the MiniTT1 or FlexTT5 off...
Page 9: Battery Chemistry
Regardless of the particular battery chemistry, the MiniTT1 and FlexTT5 regulate the batter power which gives excellent performance throughout the entire life of the batteries. The unit will continue to function normally until the batteries are nearly exhausted.
Page 10: Minitt1, Canon Or Nikon
Basic Trigger Mode consumes the coin cell battery more quickly and is not recommended when using the MiniTT1 for Nikon on a Nikon camera, or when using the MiniTT1 for Canon on a Canon camera.
Page 11: Minitt1 And Flextt5 Battery Meter In The Pocketwizard Utility
MiniTT1 and FlexTT5 Battery Meter in the PocketWizard Utility To see your battery level in the PocketWizard Utility, make sure your MiniTT1 or FlexTT5 are turned on (set to C.1 or C.2) before you connect the USB cable. Hover your mouse cursor over the battery icon to get an exact voltage and battery status.
Page 12: Safety Warnings
Operating Temperature For most PocketWizard radios, the operating temperature range is above -15° C (5° F) and below 50° C (120° F). The Nikon MiniTT1 operating temperature range is above -12° C (10° F) and below 50° C (120° F).
Page 13: Status Led
Speedlite in it set to E-TTL, this is an error. The flash needs to be set to manual (See Manual Mode for more information). <videoflash>0lHtF_8HyiE&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash> A normal green blink occurs on power up initialization and after Apply Settings has been pressed in the PocketWizard Utility. Note that a single red blink when triggering is normal operation.
Page 14 RESET A was completed. Four green blinks in a row appear when RESET B has been completed. RESET A resets channels learned in the field back to those programmed via the PocketWizard Utility. RESET B sets the radio factory default settings.
Page 15: Canon Compatibility
MiniTT1s and FlexTT5s can be updated to this version via the PocketWizard Utility. Camera Compatibility The MiniTT1 and FlexTT5 for Canon are compatible with these modern Canon digital cameras capable of using Canon's latest E-TTL II protocol: Currently Supported Cameras...
Page 16: Speedlite Compatibility
DCS 1 D2000 / D6000 BASIC TRIGGER MODE: Almost all cameras and flashes are compatible with the MiniTT1 and FlexTT5 when the radios are configured for Basic Trigger Mode. Basic Trigger Mode disables all flash power control and TTL functions of the radios.
Page 17: Previous Generation
Once that mode is enabled, the flash will work properly at HSS shutter speeds when mounted on a MiniTT1 or FlexTT5 when used as a transmitter. HSS operation is automatic (no need to set it) when used on a FlexTT5 as a receiver.
Page 18 58 AF-1 (Metz firmware v5.0) 48 AF-1 (Metz firmware v4.0) These flashes can only be used if Pre-Flash Boost is disabled on the Flash Tab in the PocketWizard Utility is disabled. Note: Pre-Flash Boost is disabled by default. These flashes may only be used on a remote FlexTT5 used as a receiver. They are not compatible as on-camera MASTER flashes.
Page 19: Nikon Compatibility
MiniTT1s and FlexTT5s can be updated to this version via the PocketWizard Utility. Camera Compatibility The MiniTT1 and FlexTT5 for Nikon are compatible with these modern Nikon digital cameras capable of using Nikon's latest i-TTL / CLS protocol: Currently Supported Cameras...
Page 20 D100 D70s BASIC TRIGGER MODE: Almost all cameras and flashes are compatible with the MiniTT1 and FlexTT5 when the radios are configured for Basic Trigger Mode. Basic Trigger Mode disables all flash power control and TTL functions of the radios.
Page 21: Flash Exposure Compensation
Nikon Compatibility Operational Notes ControlTL Remote Camera Using the default settings, remote cameras with a receiving FlexTT5 will be limited to Single Shot mode and there will be a delay between subsequent triggers. To learn more about remote camera triggering with ControlTL radios, visit our Remote Camera Triggering page.
Page 22: Nikon Special Notes
Remote Infrared Control ControlTL radios disable ALL infra-red/optical communication pulses used in Nikon’s native i-TTL system, and will not trigger remote flashes configured to receive these pulses. A PocketWizard radio is required for each remote flash you want to trigger.
Page 23: Standard Channels
Channels Channels allow you to work with other photographers or keep your triggering exclusive. Some Channels operate on different frequencies to help you avoid radio interference. All PocketWizard radios set to the same Channel work together. This section has Channel tables for the USA FCC / IC (Industry Canada) frequency radios that operate between 340 and 354 MHz.
Page 24 Standard Channels 17 through 32 Standard Channels 17 through 32 were introduced with the PocketWizard MAX. They are also called Quad-Zone Triggering Channels or MultiMAX Channels. These Channels add the benefit of Zones A, B, C, and D. Zones allow you to control up to 4 different groups of lights on the same Channel.
Page 25: Controltl Channels
ControlTL Channels were introduced with the Canon MiniTT1 and FlexTT5. They are used in all ControlTL radios like the Canon & Nikon MiniTT1 and FlexTT5, as well as the PowerST4, PowerMC2, or other ControlTL radios. These Channels allow for remote power control of compatible studio flashes, and work with ControlTL signals sent from a transmitting ControlTL radio.
Page 26: Mixing Controltl And Standard Channels
How you make this work will depend primarily on the transmitter you are using. ControlTL Transmitter If you are using a MiniTT1 or FlexTT5 as a transmitter, you can incorporate Standard Channel remotes without changing any radio settings. The MiniTT1 and FlexTT5 transmit both ControlTL and Standard Channels simultaneously, allowing any PockwetWizard receiver to be triggered in sync.
Page 27: Ce Standard Channels
Next recommended reading: Canon Compatibility or Nikon Compatibility Channels allow you to work with other photographers or keep your triggering exclusive. Some Channels operate on different frequencies to help you avoid radio interference. All PocketWizard radios set to the same Channel work together.
Page 28: Ce Controltl Channels
These Channels use the 434.22mHz frequency, and each Channel number is its own 24-bit digital code. CE ControlTL Channels ControlTL Channels were introduced with the Canon MiniTT1 and FlexTT5. They are used in all ControlTL radios like the Nikon MiniTT1 and FlexTT5, as well as the PowerST4, PowerMC2, or other ControlTL radios. These channels allow for remote power control of compatible studio flashes, and work with Canon E-TTL II and Nikon i-TTL/CLS commands.
Page 29: Learn Mode
If you are using a ControlTL transmitter like the MiniTT1 or FlexTT5 on your camera, and you want to have your flash respond to power settings from the AC3 or perform PowerTracking, make sure your radios learn a ControlTL channel.
Page 30: Engaging Learn Mode
1. Prepare your ControlTL radio for Learn Mode: MiniTT1 and FlexTT5 - turn the radio on and select the configuration to be taught, C.1 or C.2. Wait 3 or 4 seconds until you see the normal green blinks indicating the radio is ready to go with good batteries. Learning takes a lot of power for the MiniTT1 so be sure you are starting with a good coin cell battery.
Page 31 4 times, Learn Mode is engaged (amber pulsing)! Quickly release TEST and 4. Immediately press and hold TEST on the teaching transmitting radio (MiniTT1, FlexTT5, MultiMAX or Plus II). 5. When the Status LED blinks green, the channel is learned:...
Page 32 Standard channel was learned and E-TTL II will not function. If you desire E-TTL II functionality, teach the FlexTT5 again from the MiniTT1 or FlexTT5 to be used as the primary transmitter and look for 3 green...
Page 33: Programming Flextt5 Units For Controltl Operation When Teaching With A Standard Pocketwizard
Standard transmitter, you need to follow this sequence to make sure all of your FlexTT5 radios transmit and receive on the same channel. 1. Teach a transmitting FlexTT5 with a standard PocketWizard. 2. Use the programmed FlexTT5 transmitter to teach all other FlexTT5 receivers. Make sure you see 3 green blinks which confirms the ControlTL channel was learned.
Page 34: Special Notes
• For a MiniTT1 or FlexTT5 only the configuration set, C.1 or C.2, will be taught. The other configuration will retain its settings. • For a MiniTT1 or FlexTT5 all other settings as set in the PocketWizard Utility will remain in effect. If you wish to reset your radio to Factory Defaults, follow that procedure, then engage Learn Mode.
Page 35: Corresponding Channels Table
Learn Mode Corresponding Channels Table When you teach a ControlTL transmitter, like a MiniTT1, from a Standard transmitter, like a Plus II, the ControlTL transmitter learns to transmit on the Standard channel you taught it with and uses a corresponding ControlTL channel from the table below.
Page 36 Learn Mode This is also true if you are teaching one ControlTL transmitter with another - the ControlTL channel will be learned and the Standard channel will be based on the table below. If you taught it It will also transmit this ControlTL Channel on this Standard Channel You will notice in this table that it is not possible to teach Standard channels 5-16 from a ControlTL transmitter.
Page 37: Basic Wireless Ttl
Basic Wireless TTL Next recommended reading: Advanced Wireless TTL This section talks about Basic Wireless TTL where all Speedlights are used as one zone of camera-controlled light and not independently controlled using zones, groups, or ratios. Read Advanced Wireless TTL for independently controlling different groups or zones of TTL flash, or for working with ratios.
Page 38: No Flash On Camera
TTL flashes as one zone of light. All remote TTL flashes will fire at the same power level which is chosen automatically by the camera. 1. Slide a MiniTT1 Transmitter onto the camera and tighten the locking ring. 2. Slide a remote Speedlite onto a FlexTT5 Transceiver's hot shoe, tighten the locking ring, and secure the FlexTT5.
Page 39 This mode is identical to the above, adding a flash to the top hot shoe of the MiniTT1. All remote E-TTL II flashes and the master flash will be treated as one zone of light and will fire at the same power level which is chosen automatically by the camera.
Page 40: Advanced Wireless Ttl
5. Adjust flash output level compensation using MASTER Speedlight flash controls. 6. Make sure all your PocketWizard radios are on the same channel and take pictures normally. IMPORTANT: Nikon Speedlights set to REMOTE = ON and connected to remote FlexTT5 radios will not function properly as remotes.
Page 41: High Speed Sync
High Speed Sync Next recommended reading: PowerTracking The MiniTT1 and FlexTT5 support High Speed Sync (HSS) for Canon and FP Sync for Nikon. No configuration is necessary for the radios. • If you have a Nikon camera, adjust the Flash Sync Speed setting in the Custom menu to 1/250s (AutoFP) for most cameras.
Page 42 High Speed Sync References [1] http:/ / www. canon. co. jp/ imaging/ flashwork/ ettl2/ high/ index. html [2] http:/ / www. nikonusa. com/ Learn-And-Explore/ Nikon-Camera-Technology/ ftlzi4zp/ 1/ Auto-FP-High-speed-Sync. html...
Page 43: Remote Manual Flash Control From Camera Position
FlexTT5 to receive on a Standard Channel via Basic Trigger Mode. This can be set in the PocketWizard Utility, under the Misc Tab while shooting on-location via Learn Mode. See the tutorial on Learn Mode here.
Page 44: Basic Power Control
See the section on Using an AC3 ZoneController for more information. Basic Power Control With only a MiniTT1 or FlexTT5 on your camera, your camera’s FEC (Flash Exposure Compensation) control will adjust your flash power output level for all supported flashes connected to ControlTL receivers. Nikon Only The camera’s FEC or EC (Exposure Compensation) control will adjust flash power output level.
Page 45: Automatic Powertracking
Center Point section for more information. To set the aperture and ISO values that will be aligned with the ControlTL center point: • Turn on your camera and transmitting MiniTT1 or FlexTT5, but wait to press your shutter button or take any pictures.
Page 46: Using An Ac3 Zonecontroller
• On the Power Dials of the AC3 ZoneController • On the camera for all zones except AC3 Manual zones • For transmitting radios, the PocketWizard Utility can adjust the PowerTracking center point for ISO and aperture which affects all zones •...
Page 47: What Is Hypersync
HyperSync, and some example images illustrating the results you can expect. What is HyperSync? HyperSync is a feature exclusive to PocketWizard radios that allows you to shoot at speeds faster than your cameras X-Sync while using studio strobes.
Page 48: When To Use Hypersync
When to Use HyperSync HyperSync has been available since just after the introduction of the MiniTT1 and FlexTT5, but we have found that there are still many photographers who don’t know how HyperSync can help them. Below are three of the most common uses of/reasons to use HyperSync.
Page 49: Overpowering The Sun
HyperSync Overpowering the Sun When using HyperSync you can reduce the ambient light apparent in your photograph by using higher shutter speeds, but still achieve sync with studio strobes. This means in bright sunlight you can darken the ambient light in the background. Being able to achieve higher shutter speeds also allows you to use a wider aperture.
Page 50: Hypersync Performance With Your Camera
HyperSync Performance with your Camera One of the most common questions we receive about HyperSync is “What kind of results can I get with my gear?” We at PocketWizard have been testing HyperSync performance and recording the outcome of many of the most popular camera and flash combinations. To view the results for your gear select your camera from one of the grids below, and find your lighting system on the subsequent page.
Page 51: Hypersync Setup
If you don't see your equipment, feel free to contact us directly: http:/ / www. pocketwizard. com/ contact/ inquiry/ The results below were produced with the steps detailed on the bottom parts of this page.
Page 52: All Controltl Radios - Hypersync Automation
While default HyperSync settings for ControlTL radios will usually provide great results, they may also be reconfigured by the photographer. First configure your transmitting MiniTT1 or FlexTT5, and then your receiving PocketWizard radio. Steps for configuring your ControlTL transmitter and receiver are detailed below.
Page 53: How To Configure The Controltl Transmitter
HyperSync Setup How to Configure the ControlTL Transmitter When using a MiniTT1 or FlexTT5 as a transmitter to perform HyperSync, follow these steps to configure your radio. For Nikon users: For the most consistent results and most flash energy in frame with Nikon radios, it is highly recommended that you enable “HyperSync Only:”...
Page 54: How To Configure The Receiving Flextt5 And Ac9 Alienbees Adapter
When using a Canon or Nikon FlexTT5 with an attached AC9 AlienBees Adapter as your receiver, follow these steps to configure your radio: 1. Connect your receiving FlexTT5 to the PocketWizard Utility via USB and make sure that the “Advanced Mode” box is checked 2.
Page 55: How To Configure The Receiving Powermc2
How to Configure the Receiving PowerMC2 When using a PowerMC2 as your receiver, follow these steps to configure your radio: 1. Connect your PowerMC2 to the PocketWizard Utility via USB, and make sure that the “Advanced Mode” box is checked 2.
Page 56: How To Configure The Receiving Powerst4
You can read more about this behavior on the IGBT-controlled flashes vs. Voltage-controlled flashes page. Before you connect a PowerMC2 to the PocketWizard Utility via USB, make sure to disconnect the radio from the Einstein flash. Failure to disconnect the PowerMC2 from the flash before connecting it to the Utility could result in damage to the radio.
Page 57 HyperSync Setup This video shows you how to set up your transmitter and receiver for HyperSync for the Nikon system of radios. <videoflash>Z_9-oGivLDg&loop=0&rel=0?&autohide=1|475|290</videoflash> This video shows you how to set up your transmitter and receiver for HyperSync for the Canon system of radios. <videoflash>AZEOnuma6-k&loop=0&rel=0?&autohide=1|475|290</videoflash>...
Page 58: How To Configure The Receiving Flextt5 P2 Port
When using a FlexTT5 as your receiver connected to a flash via the P2 port, follow these steps to configure your radio: 1. Connect your receiving FlexTT5 to the PocketWizard Utility via USB, and make sure that the “Advanced Mode” box is checked 2.
Page 59: Controltl Transmitter, Standard Receiver (Plus Ii, Plus Iii, Plusx, Multimax)
The transmitting MiniTT1 or FlexTT5 can account for the flash duration of remote flashes in one of two ways, “ HyperSync Flash Duration For Standard Channels” or “ Manual HyperSync For Standard Channels.” Find more information on these options on the HyperSync/HSS Tab page.
Page 60: How To Configure The Controltl Transmitter - Manual Hypersync For Standard Channels
How to Configure the ControlTL Transmitter - Manual HyperSync For Standard Channels Follow these steps to configure your ControlTL transmitter using Manual HyperSync For Standard Channels: 1. Connect your transmitting MiniTT1 or FlexTT5 to the PocketWizard Utility via USB and make sure that the “Advanced Mode” box is checked 2.
Page 61: Understanding Hypersync And High Speed Sync
HyperSync Setup If you notice clipping in frame, choose a different Manual HyperSync Offset value – typically the maximum offset (slider all the way to the left) works well as a starting point. Not all cameras can use the full range of this setting. Some cameras will show no change beyond certain offset value.
Page 62 HyperSync. There are countless combinations of flashes and cameras in the world, and we will add more cameras and flashes as time goes by. If you don't see your equipment, feel free to contact us directly: http:/ / www. pocketwizard. com/ contact/ inquiry/ Canon Camera HyperSync Results...
Page 63: How Does A Flash Work
Understanding HyperSync and High Speed Sync Nikon Camera HyperSync Results Nikon D4S Nikon D810 Nikon D7100 Nikon Df Nikon D4 Nikon D800 Nikon D7000 Nikon D3x Nikon D800E Nikon D5300* Nikon D90 Nikon D3s Nikon D700 Nikon D5200* Nikon D80 Nikon D3 Nikon D610 Nikon D5100* Nikon D40x*...
Page 64: X-Sync - Flash Behavior With Normal Sync Limits
Understanding HyperSync and High Speed Sync A simulated shutter above X-sync] The faster the shutter speed, the smaller the slit: Faster shutter speeds have smaller slits X-sync - Flash behavior with normal sync limits A flash directly connected to a camera Your camera has a limit where it can fully open its shutter and capture flash across the entire sensor all at once.
Page 65 Understanding HyperSync and High Speed Sync the slit becomes. 5. The first curtain reaches the bottom of the sensor. 6. The camera triggers its PC terminal and the center sync pin on the hot shoe. (Many cameras do not provide this sync output above X-sync.) 7.
Page 66: Reduced Clipping
2. Several milliseconds of time pass. This is called lag time. The amount of lag time varies from camera to camera. 3. The attached MiniTT1 or FlexTT5 senses exactly when the shutter will fire, and then fires the flash early.
Page 67: Highest Energy
Channel (meaning a (Plus II, Plus III, PlusX, MultiMAX, FlexTT5 in Basic Trigger Mode), or internal PocketWizard receiver built in to your flash.) This is done by following the directions for the How to Configure the ControlTL Transmitter - HyperSync Flash Duration For Standard Channels section, and trying to eliminate clipping at your lower HyperSync speeds without "clipping"...
Page 68: Factors To Consider
Understanding HyperSync and High Speed Sync Factors to consider There are many factors that may impact HyperSync performance. Flash Duration • Flash duration is a critical factor in HyperSync performance. The flash duration is the length of time from when your flashtube is first energized to when it is no longer emitting energy.
Page 69 Understanding HyperSync and High Speed Sync Camera Choice • Cameras with larger and slower shutters can produce more noticeable gradation. Cameras with faster moving shutters and smaller sensors can improve HyperSync success by minimizing gradation. Faster or slower moving shutters are not the same as your camera's shutter speed setting. Camera Choice Ranger RX (S Head) at full power, 1D Mark IV 1/8000th f/22 (Faster Shutter)
Page 70 • Put your flashes where you want, without worrying about accessing them during a shoot. AC3 Quick Start How-To 1. Slide the AC3 onto your on-camera MiniTT1 or FlexTT5. Power on the transmitter, then the camera. 2. Set up remote Speedlights on FlexTT5 radios normally. Power on the flash, then the FlexTT5.
Page 71 The mode switches control the modes of operation for ControlTL receiving radios. It also controls zone on/off for PocketWizard Standard Channel Receivers with Quad-Triggering Zones, like the MultiMAX, Plus III, or flash packs with built-in PocketWizard radios, when using Standard Channels 17 or higher.
Page 72 AC3 ZoneController Release Button Press the release button to remove the AC3 from your transmitter. Status LED The green Status LED blinks occasionally to indicate normal operation. Power Dials Sets the flash output power. AC3 Power Control Chart (Manual) AC3 Power Dial Setting Speedlights Most White Lightning ControlTL...
Page 73 Power Control for Non-Compatible Cameras You can use your MiniTT1 or FlexTT5 with an AC3 ZoneController on nearly *any* camera with a basic hot shoe to get Manual Power Control for Mamiya, Leica, Hassleblad, mirrorless cameras, etc. Trigger any ControlTL receiver in sync up to 1/125 on some models of camera.
Page 74: Pocketwizard Utility
Advanced features in the MiniTT1 and FlexTT5 are available when using the PocketWizard Utility and connecting your radio to your PC or Mac via a USB cable. The PocketWizard Utility allows you to update your USB enabled PocketWizard with the latest Firmware and adjust the features of the MiniTT1 and FlexTT5. The latest version of the utility can be downloaded from pocketwizard.com...
Page 75 The MiniTT1 and FlexTT5 auto detect when the USB cable has been connected. To see the battery level, the MiniTT1 and the FlexTT5 need to be powered on for at least 3 seconds before plugging in the USB cable. PocketWizard Utility FAQ...
Page 76: Factory Reset
Learn Mode or Factory Reset, read about the Status LED to see the difference. Reset A - Reset Channels Only RESET A: Returns both C.1 and C.2 to the channels you last set in the PocketWizard Utility. Reset A is primarily used for resetting channels that were taught in the field.
Page 77: Multimax Factory Reset
3. When you see the "CLEAR/RESET" message on the LCD, release C. The radio is reset to factory defaults. Default Settings When you perform a Factory Reset, the settings below are used. MiniTT1 and FlexTT5 Default Settings Utility Tab Quick Links Update...
Page 78 Transmitter Only = disabled - FlexTT5 Only Disable Shoe Communications = disabled - FlexTT5 Only SpeedCycler = disabled Top Shoe Detection Mode = AC3/AC9 - Canon MiniTT1 and FlexTT5 Only Camera Model = Auto - Canon MiniTT1 and FlexTT5 Only...
Page 79: Powerst4 Default Settings
Factory Reset PowerST4 Default Settings Channel Tab Use ControlTL for Rx Channel = enabled ControlTL Channel 1, Standard Channel 1 Exposure Tab Exposure Compensation = 0.0 Sleep Tab Modeling Light Sleep Mode = enabled Modeling Light Sleep Delay = 600 secs/10 minutes Misc Tab Ranger RX Head Selection = S-Head Digital 1200/2400RX Head Selection = Digital S...
Page 80: Update Tab
FTP communications through your network firewalls, if necessary. • Click the Check For Updates button under the Updates tab. • If there is an update to the PocketWizard Utility, a new window will give you a link to download the new firmware.
Page 81: Channel Tab
Mode. The FlexTT5 can operate as a receiver for any PocketWizard transmitter. When a MiniTT1 or FlexTT5 is used as a transmitter, it always sends out two triggers. One is a ControlTL trigger on a ControlTL channel, and the other is sent on a Standard Channel. This enables you to use TTL or power-controlled...
Page 82 Note: When the MiniTT1 is plugged in it only shows the Transmit drop downs - ControlTL Tx and Standard Tx - because it is a Transmitter. The FlexTT5, a Transceiver, will show both Transmit and Receive options, because it perform both operations.
Page 83: Flash Tab
Receiving radios can only listen on one channel at a time; either ControlTL or Standard. If your transmitter is a MiniTT1 radio and you are triggering a remote radio that is expected to respond to E-TTL II commands, then you must use a ControlTL channel.
Page 84 Flash Tab Rear Curtain Sync Begins At (Canon Only): Canon Only Use this setting to control the shutter speed that Rear Curtain Sync begins at with your Canon camera. The default setting is 1/100th. (Nikon's Rear Curtain Sync is controlled on the Camera Body instead, and begins at 1/125th.) Read more about Rear Curtain Sync here.
Page 85 Flash Tab Force TTL Master Mode (Canon Only): Canon Only This mode enables the use of a Speedlite that lacks Master Mode in the shoe of a ControlTL transmitter to trigger remote flashes. The transmitter tells the camera that Master Mode is active even though that mode is not available or set in the flash.
Page 86: Hypersync/Hss Tab
HyperSync/HSS Tab HyperSync/HSS Tab Utility Tab Quick Links Update Channel Flash HyperSync/HSS PowerTracking Modeling Sleep Misc Exposure Fast Moving Page! The information on this page is potentially changing hour by hour or day by day as authors are actively generating content. This could be due to a recently improved feature or announcement, or as the result of a large body of behind-the-scenes work coming to fruition.
Page 87: Hss/Fp Begins At (Hypersync Ends)
HyperSync/HSS Tab HSS/FP Begins At (HyperSync Ends) Select the shutter speed where HyperSync Timings are no longer used and High Speed Sync/FP Flash is engaged. For example, selecting 1/1250th for this dropdown will use HyperSync at shutter speeds up to and including 1/1000th, and begin using High Speed Sync.
Page 88: P2 Hypersync Flash Duration
HyperSync/HSS Tab • Shooting outdoors where the sky is a major factor in the top part of the image • Using aperture priority in conditions that cause the shutter speed to go above X-sync • In any situation where the full frame must be used and cropping is not an option "Reduced Clipping"...
Page 89: Powertracking Tab
PowerTracking allows you to adjust your remote studio flash's output power via the camera's FEC, ISO, and aperture controls. PowerTracking happens automatically when you have a MiniTT1 or FlexTT5 on a Canon or Nikon camera and you are controlling a compatible studio flash connected to a supported PocketWizard radio.
Page 90 Center on ISO & Aperture with First Shot The aperture and ISO as set on the camera for the first exposure after powering on the MiniTT1 or FlexTT5 will be used as the center values for PowerTracking. For example, if your camera is set to ISO 100 and F:5.6 for its first exposure, then those exposure settings will equal 3 stops down from your flash's maximum output power.
Page 91: Modeling Tab
PowerTracking Tab Aperture Centered On: Use this control to specify the PowerTracking center point relative to aperture. ISO Centered On: Use this control to specify the PowerTracking center point relative to ISO. AC9 Flash Exposure Compensation: (FlexTT5 Only) Use this control to adjust the FEC of the flash directly connected to the AC9 in this receiving radio's hot shoe. This setting is cumulative with other FEC values set in the system.
Page 92: Sleep Tab
Modeling Tab Modeling Light Autotrack Enable this control for the modeling light level to track with the camera exposure or AC3 Power Dial settings. Modeling Light Active XX% Sets the active output level of the modeling light if Autotrack is not used. Modeling Light Sleep Check this box to have the modeling light automatically go to a set output level after a set time.
Page 93 Sleep Tab Remote TTL Flash Sleep Mode Normally your ControlTL transmitter tells all remote TTL flashes to sleep when the camera sleeps. This saves batteries in the remote flash but could cause the flash to take a moment to be ready before the next trigger. Enable this control to have your ControlTL transmitter wait to tell all remote E-TTL II flashes to sleep until a time after the camera sleeps.
Page 94 Sleep Tab Modeling Light Sleep Mode (PowerST4 / PowerMC2 Only) If you are using a standard transmitter like a Plus or MultiMAX, a sleep command is never sent over the air, and the remote flash mounted on the radio would always remain powered on. Enabling this control causes the connected flash to remain awake for a set period after any radio activity, then enter its sleep mode for power saving.
Page 95 Basic Trigger Allows the MiniTT1 or FlexTT5 to operate as a basic PocketWizard radio slave on any camera it will fit, including cameras other than the Canon or Nikon models the radio is designed for. This mode only uses the center hot shoe contact for sync input and output.
Page 96 Transmitter Only (FlexTT5 Only): Allows the FlexTT5 to be used as a Transmitter only, just like the MiniTT1. This mode allows a photographer to work in the same area as other photographers, and share remote flashes, without the flash on top of the FlexTT5 being triggered by the other photographers.
Page 97 Misc Tab Ranger RX Head Selection (PowerST4) Only Use this setting to select the flash head in use with your Ranger RX series pack. Digital 1200/2400RX Head Selection (PowerST4) Only Use this setting to select the flash head in use with your Digital RX series pack. Flash Model (PowerST4) Only Use this setting to determine what kind of Elinchrom monobloc or flash pack you are using with your PowerST4.
Page 98: Remote Camera Triggering
FlexTT5 attached to the camera has either Disable Shoe Communications or Basic Trigger Mode set via the PocketWizard Utility. It is not possible to combine continuous remote camera triggering with advanced features like TTL and FP/High Speed Sync. Relay Mode with TTL is only available in single shot mode.
Page 99: Remote Camera Cables
A camera can be remotely pre-released when connected via an ACC cable to a compatible Pocketwizard radio. They can be used with the ACC port on a MultiMAX or the P1 port on a FlexTT5. Note: -ACC cables shipped into the market starting July/August 2013 include an MSMM Adapter (stereo to mono miniphone) which converts a -ACC cable to a standard miniphone cable.
Page 100 Remote Camera Triggering FlexTT5 + ACC Cable Compatibility Chart FlexTT5 Configuration Supported Behaviors Receiving on a ControlTL Remote camera triggering in single shot mode Channel Relay Mode for Standard and ControlTL Channels Attached to camera's hot shoe Receiving on a ControlTL Unsupported Channel Remote camera cannot be triggered...
Page 101 These limitations are tied to the camera’s auto-focus system – you will see the same behavior with or without PocketWizard radios. References [1] http:/ / www. pocketwizard. com/ products/ cable_accessory/ accessories/ msmm/ [2] http:/ / www. pocketwizard. com/ products/ cable_accessory/ accessories/ ptmm/...
Page 102: Relay Mode
You can trigger flashes in sync with your remote camera. This is called Relay Mode. Here’s how it works: • Press TEST on a PocketWizard that you are holding in your hands. • The FlexTT5 connected to your remote camera receives the signal and triggers your camera.
Page 103: Controltl Accessories
ControlTL Accessories ControlTL Accessories AC7 RF Hard Shield...
Page 104 • Check your batteries - sometimes low batteries can affect radio performance. • Make sure all of your radios have been updated to the latest firmware. Connect your radio to the PocketWizard Utility and navigate to the "Update Tab." Click the “Check for Updates Button.”...
Page 105 Our radios are sold in two different versions to comply with radio laws in different countries. In the United States, the FCC reserves the 344-354 MHz frequency for PocketWizard systems. In Europe, regulations assign 433-434 MHz. A PocketWizard sold in the USA bears the letters “FCC” on the outer shell; a European version will have the letters “CE.”...
Page 106: Minitt1 And Flextt5 Faq
[1] http:/ / www. pocketwizard. com/ MiniTT1 and FlexTT5 FAQ Do you have a question about your MiniTT1 or FlexTT5? Check out these Frequently Asked Questions, compiled by PocketWizard tech support Is my camera or flash compatible with ControlTL radios like the MiniTT1 and FlexTT5? Check out our Canon Compatibility and Nikon Compatibility pages for specific information on your gear.
Page 107 MiniTT1 and FlexTT5 FAQ quickly as you can press the test button on the radio in your hand. How can I increase my range? Check out our Long Range Performance page for tips. Contact PocketWizard tech support for help with unique long-distance setups.
Page 108: Long Range Performance
Long Range Performance Long Range Performance Next recommended reading: MiniTT1 and FlexTT5 Specifications {{{annotations}}} Antenna performance comparisons. <!-- --/> Long distance performance from your PocketWizards depends on the orientation and position of the radios. Whenever possible, try to maintain a line of sight between the radios and keep the antennas parallel. While radio does not require line of sight, it does help dramatically.
Page 109: Range Extending Options
A few Canon flashes, including the popular 580EX II, 580EX and 430EX, emit strong RF noise across the frequency range used by PocketWizard radios, impacting both the FCC 344MHz radios used in the American market and the CE 433MHz radios used in Europe and other international markets. This interference can impede the out-of-box range performance with any PocketWizard radio.
Page 110: Use The Default C2 Setting On The Receiving Flextt5 Transceiver
2, 4, 5, 6 & 20. A channel frequency guide can be found on the Channels page. Use a FlexTT5 Transceiver as your transmitter and your receiver. As a transmitter, the FlexTT5 Transceiver has a more optimize-able antenna than the MiniTT1 Transmitter and will improve range up to 20%.
Page 111: Hardware Options
Long Range Performance Orient your antenna so that the tip of the antenna is a vertical straight line with the opposite corner of the FlexTT5 Transceiver. Yes, it's a bit contorted but it works. Hardware Options Use a Canon OC-E3 cord. Ideally, use the cord with a ferrite choke added to the end of the cord nearest the flash, to separate the flash from the FlexTT5 Transceiver.
Page 112: Mount Your Flash On One Light Stand And Your Flextt5 Transceiver On Another Stand
Long Range Performance {{{annotations}}} Best <!-- --/> {{{annotations}}} Ferrite Choke <!-- --/> Mount your flash on one light stand and your FlexTT5 Transceiver on another stand. Just be sure there is at least 18" between the Flash and the FlexTT5. - Use a wide dual light bracket to separate the FlexTT5 Transciever from the flash.
Page 113: Use Flashes That Have No Noise Issues
The range of this flash is almost as good as the 430EX II. It is compact and easy to carry with the FlexTT5. Note: The 600EX (not RT) has not yet been tested. Use a PocketWizard designed AC7 Hard Shield for Canon Speedlites. {{{annotations}}} AC7 Hard Shield.
Page 114: Use A Pocketwizard Designed Ac5 Soft Shield For Canon Speedlites
Long Range Performance Use a PocketWizard designed AC5 Soft Shield for Canon Speedlites. {{{annotations}}} AC5 Soft Shield. <!-- --/> The AC5 RF Soft Shield was designed to block the RF emissions from certain flashes (580EX II, 580EX and 430EX) from interfering with the FlexTT5, allowing the FlexTT5 to work at considerably longer range. For proper performance the AC5 must be installed correctly.
Page 115: Beta Firmware
Beta Firmware With the latest public release candidate, or beta firmware, you get to try out MiniTT1 and FlexTT5 or other radios' firmware and features currently being developed and assist us in the final stages before a “Final Release” is available.
Page 116: Enabling Beta Firmware
Beta Firmware Enabling Beta Firmware 1. To enable access to beta firmware, open PocketWizard Utility, and navigate down to the blue gear in the bottom left corner of the window. 2. Navigate over to the "Firmware Updates" tab. 3. Navigate down to the bottom and check "Yes, I would like to have...
Page 117 For a beta program to to be of value to us in improving PocketWizard firmware, we need feedback on your experiences with testing the beta firmware. Feedback can include your opinion of overall functionality or any bugs or issues you may have encountered.
Page 118 Beta Firmware References [1] http:/ / www. pocketwizard. com/ support/ downloads/ beta [2] http:/ / www. pocketwizard. com/ contact/ [3] mailto:betalab@pocketwizard. com [4] http:/ / www. facebook. com/ pocketwizards Mounting Next recommended reading: Long Range Performance In order to achieve the best results using our radios, antenna position and placement must be considered. The photos below illustrate the optimal position for the FlexTT5 as a receiver.
Page 119: The Fcc Wants You To Know
2. Increase the separation between the equipment and the receiver. 3. Consult the dealer or an experienced radio or television technician for help. Canon MiniTT1 FCC ID Number: KDS-PW3-004 Canon FlexTT5 FCC ID Number: KDS-PW3-005 Nikon MiniTT1 FCC ID Number: KDS-PW3-007...
Page 120 Status LED Source: http://wiki.pocketwizard.com/index.php?oldid=2713 Contributors: Chris, Ian, Patrick, Seth, Zachary Canon Compatibility Source: http://wiki.pocketwizard.com/index.php?oldid=3049 Contributors: Chris, Heather, Heathers, Ian, Patrick, Seth, Steve, Zachary Nikon Compatibility Source: http://wiki.pocketwizard.com/index.php?oldid=3158 Contributors: Chris, Eric, Heather, Heathers, Ian, Patrick, Seth, Steve, Zachary Channels Source: http://wiki.pocketwizard.com/index.php?oldid=3025 Contributors: Heathers, Ian, Patrick, Steve, Zachary Channels (CE/Europe) Source: http://wiki.pocketwizard.com/index.php?oldid=2983 Contributors: Heathers, Ian...
Page 121 File:Garrison.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:Garrison.jpg License: unknown Contributors: Chris File:Pocketwizard-olli-krause-02.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:Pocketwizard-olli-krause-02.jpg License: unknown Contributors: Chris File:Eric Seo 20130516 S D'Artois 010.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:Eric_Seo_20130516_S_D'Artois_010.jpg License: unknown Contributors: Chris File:Motorcycle shot w logo and info.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:Motorcycle_shot_w_logo_and_info.jpg License: unknown Contributors: Seth File:7d motorcycle gradient.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:7d_motorcycle_gradient.jpg License: unknown Contributors: Seth File:Hypersync setup.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:Hypersync_setup.jpg License: unknown Contributors: Seth...
Page 122 Image Sources, Licenses and Contributors File:Firmware_updates_download_availability.png Source: http://wiki.pocketwizard.com/index.php?title=File:Firmware_updates_download_availability.png License: unknown Contributors: Heather Image:Velcro.jpg Source: http://wiki.pocketwizard.com/index.php?title=File:Velcro.jpg License: unknown Contributors: Chris...

This manual is also suitable for:

Flextt5

PocketWizard MiniTT1 Manual

Quick Links

Need help?

Questions and answers

Related Manuals for PocketWizard MiniTT1

Summary of Contents for PocketWizard MiniTT1

This manual is also suitable for:

Table of Contents