Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SVP HDT-02
Summary of Contents for SVP HDT-02
- Page 1 Broadcast Microwave HIGH DEFINITION DIGITAL CAMERA TRANSMITTER HDT-02 USER MANUAL V1.0...
- Page 2 It is also explained how the information is shown on the display, transmitter’s menus, alarms, etc. Chapter 4: Applications In this last chapter some interesting applications for the HDT-02 transmitter system are shown. HDT-02 High Definition Digital Camera Transmitter...
- Page 3 We are sure that the addition of this equipment to your existing installation will cause you nothing but satisfaction. Please read these instructions carefully, and keep them at hand in case you have to refer to them. HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:...
-
Page 4: Important Notes
8. When an audio channel is not used it should be disabled. 9. The HDT-02’s keypad is locked when it is not operated for 3 minutes. To unlock it right arrow button should be pressed for several seconds. -
Page 5: Table Of Contents
Power supply voltage alarm ............ 24 5.6 Temperature alarm ..............24 6 HD Upgrade ................25 CHAPTER4: Applications 1 Introduction ................26 2 Applications example ciones ............27 2.1 Iphone application ..............27 HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... -
Page 6: Chapter 1: Introduction
MP@HL, MP@ML and 422@ML. Minimum latency when super low delay option is selected is 45ms. The HDT-02 transmitter has a Transport Stream ASI input so it can be used as a repeater. It is available in 3 different frequency ranges: from 2.0 to 2.5GHz, from 2.2 to 2.6GHz and from 3.4 to 3.7GHz. -
Page 7: Chapter2: Technical Features
Selectable (only with micro level) Maximum input level: +15dBm Signal to noise ratio: >70dB Input impedance: 20KΩ Audio coding: MPEG-2 Layer1 Audio simple rate: 48 KHz Audio Bitrate: 128, 192, 256, 384 KHz HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... - Page 8 IDC V Clip or Anton Bauer Physical features: Dimensions: Width: 110mm Height: 45mm Depth: 175mm Weight: 0.95Kg Operation temperature: -10 a 45ºC Audio and power supply cables are supplied with the HDT-02 camera transmitter HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:...
-
Page 9: Connections
2 Connections Every connection of the HDT-02 camera transmitter is on the rear panel, except for the RF antenna connection that is on the front panel. All the input/output connections of the camera transmitter are shown in the figure below: Figure 2.1 HDT-02 Connections... -
Page 10: Power Supply
SDI digital video input signal type is SMPTE 292 compliant. It is important that 75Ω connectors are used. This is because the female input connector of the HDT-02 unit may be damaged and because an impedance mismatch will occur. Table 2.2 Video input signal connection features... -
Page 11: Audio Inputs
31.65 Mbit/s 2.3 Audio inputs The HDT-02 has 4 analogue audio input signals that are inserted in pairs via two 5 pin Lemo 0B connectors on equipment’s rear panel. Only balanced audio signals are accepted. Audio cables are supplied with the equipment. -
Page 12: Rf Output/Antena
2.4 RF output/Antena The antenna is directly connected to the female N-type connector on the front panel of the HDT-02 camera transmitter. Table 2.5 RF output characteristics Item Features Connector label RF ANTENNA Connector type N female Output frequency range 2.0-2,5GHz... -
Page 13: Chapter3: Transmitter Operation And Menus
Guard Interval (1/4, 1/8, 1/16 o 1/32) Transmitted bitrate (Mpbs) Input Audio Input Selection Status Profile Type Frequency Latency Output Modulation bitrate Scheme Guard Interval Figure 1.1 HDT-02’s front panel/ Main screen HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... - Page 14 The Led lights up in green when the equipment is turned on If the equipment is locked the Led flashes in green The Led flashes green and red if the HDT-02 is alarmed. When the input signal type is configured to be composite video a “V” is displayed in the input signal selection.
-
Page 15: Front Panel
2 Front panel The HDT-02 camera transmitter is configured following a menus structure on the display. The front panel has 5 buttons to enter and exit the equipment’s control menus and submenus and to navigate through them. -
Page 16: Left Button
This buttons are also used to change the frequency and PID parameter’s values. Pressing up and down arrows the value of those parameters can be changed, increased or decreased respectively. Figure 2.3 Left, Up, Down and Right buttons HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... -
Page 17: Menus
1. Frequency 2.0 to 2.5GHz Transmission frequency configuration 2.2 to 2.6GHz Frequency range depends on HDT-02 model 3.4 to 3.7GHz If configured frequency is out of equipment’s frequency range the transmitter adjusts it to nearest frequency inside allowed frequency band 2. - Page 18 TS Parameters Video PID PID values Audio1 PID Audio2 PID PMT PID PCR PID Prog. Number Tx. BitR: 4.95 – 31.65Mpbs Transmitted bitrate. Depends modulation scheme, FEC and guard interval used. HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:...
-
Page 19: Transmitter Operation
To enter the main menu of this equipment left button should be pressed. Two options are displayed: Monitor and Setup. To choose one or the other up and down arrows are used. Once one is selected, right button should be pressed. HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... -
Page 20: Change Of A Parameter/ Setup Menu
Once the parameter has been selected, as right button is pressed, the operator navigates through the different options for the modulations scheme parameter: QPSK, 16QAM or 64QAM. Figure 4.2 Modulation scheme selection: QPSK Figure 4.3 Modulation scheme selection: 16QAM HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... - Page 21 Then, press right arrow again and the equipment will be locked onto that frequency Figure 4.6 Frequency parameter configuration. The cursor on the las digit HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:...
-
Page 22: Monitoring A Parameter/Monitor Menu
Figure 4.8 TS parameter submenu access To exit a submenu or a parameter press Left arrow. HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... -
Page 23: Alarms
5 Alarms If an alarm is triggered in the HDT-02 camera transmitter, the led in the front panel flashes red and green. To determine which alarm has been triggered the display in the front panel should be observed. The value of the parameter that has triggered the alarm will blink in the display. -
Page 24: Asi Overflow Alarm
5.4 Transmission frequency alarm Once the frequency has been set if there is any RF problem and the equipment is not locked onto that frequency the frequency value blinks on the display. HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:... -
Page 25: Power Supply Voltage Alarm
Figure 5.5Main Screen. Power supply voltage alarm 5.6 Temperature alarm When the temperature inside the HDT-02 camera transmitter reaches or exceeds 65ºC, an alarm is triggered and the second line on the main screen is alternated every three seconds with another line where temperature and voltage values are displayed. -
Page 26: Hd Upgrade
The transmitter gives the user three choices to insert the correct keyword. In case no correct word is introduced the transmitter is blocked in SD and it will have to be sent to SVP to unblock it and to be able to carry out the HD upgrade. -
Page 27: Chapter4: Applications
Chapter 4: Applications 1 Introduction The HDT-02 camera transmitter is a very versatile equipment. Used together with other SVP Broadcast Microwave equipments much more than a camera transmitter is achieved This equipment allows multiple configurations: 1. On its own it is a robust, lightweight, easy-to-use camera transmitter. It has a display and a keypad on the front panel. -
Page 28: Applications Example Ciones
These applications aim to simplify easy but also complicated life TV (see figure) signal transmissions. The use of the HDT-02 camera transmitter makes possible to reduce the space needed for the transmission equipment. Besides, due to the DC/DC converter in the equipments it is possible to install them in vehicles as cars, motorbikes, helicopters, etc. - Page 29 PDA or the Iphone. The figure below shows the scheme to be used: Figure 2.2 Iphone application HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:...
- Page 30 Notes: HDT-02 High Definition Digital Camera Transmitter USER’S MANUAL V1.0:...
- Page 31 Final note SVP Broadcast Microwave S.L. is constantly striving to improve all of its products. Therefore, we ask you to understand that modifications may occur in designs, equipment and technology. Consequently, no responsibility can be derived from the information, illustrations or descriptions contained in this manual.
- Page 32 SVP Broadcast Microwave reserves the right to make changes to this manual and to the equipment without prior notice. Broadcast Microwave C/Uralde, 2 48215 Iurreta Vizcaya – España Tel: (+34) 94620 3722 Fax: (+34) 94620 4356 svpbm@svpbm.com www.svpbm.com...
Need help?
Do you have a question about the HDT-02 and is the answer not in the manual?
Questions and answers