1. Manuals
  2. Brands
  3. SVP Manuals
  4. Transmitter
  5. UDT-70
  6. Manual

SVP UDT-70 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
UDT-70 TRANSMITTER MANUAL
V1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UDT-70 and is the answer not in the manual?

Questions and answers

Related Manuals for SVP UDT-70

Summary of Contents for SVP UDT-70

  • Page 1 UDT-70 TRANSMITTER MANUAL V1.0...
  • Page 2 Accessories included in this manual: SCDA HAP-60...
  • Page 3 Chapter 7: Up Converter This section provides the user all the necessary information to understand the general operation characteristics of the up-converter. Index A: T-Box Index B: SCDA User’s Guide Index C: HAP User’s Guide UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 4 Dear customer, We would like to thank you for selecting this equipment and welcome you to the SVP’s growing family of products. We are sure that the addition of this equipment will cause you a complete satisfaction in your existing installation.
  • Page 5 About this manual This user’s guide provides indications and explanations about how to set up easily the UDT-70 transmitter for the most common use cases. This document is intended to help first time users: To find their way around the GUI.
  • Page 6 Important Notes 1. The UDT-70 Ultra High Definition transmitter is completely compatible with the DVB-T/T2/S2/S Standards, included in the European Standard ETSI EN300744 (DVB-T), ETSI EN300755 (DVB-T2), ETSI EN302307 (DVB-S2) and ETSI EN300421 (DVB-S). 2. The control unit has available a 70 MHz output connection through which it is possible to transmit the signal to the RF head via a triax cable in DVB- T2, DVB-T, DVB-S2 or DVB-S mode.
  • Page 7 7. In the case of injuries to the mouth, it may be necessary to use mouth- to-nose resuscitation. Seal the victim’s mouth with your cheek and blow firmly into his nose, proceeding as above. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 8 If help as available or as soon as resuscitation is no longer required the wound should be covered with a DRY clean dressing. d) Oil or grease in any form should not be applied. e) If severely burnt, get the victim to hospital immediately. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 9: Table Of Contents

    Rack Unit Installation ......................124 Up-Converter and parabolic antenna installation .............. 124 Antenna Installation ......................125 Chapter 7: Up Converter ..................126 Front Panel ......................... 126 Display ..........................127 7.2.1 Main screen ........................127 UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 10 A.1 Mechanical Drawing ..................132 Index B: SCDA User’s Guide ................... 133 B.1 Description ..................... 134 B.2 Technical Specifications .................. 135 B.3 Configurations ....................136 C.1 Description ..................... 139 C.2 Technical Specifications .................. 140 UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 11: Chapter 1: Introduction

    Chapter 1: Introduction The UDT-70 is a split box portable microwave transmitter, which consists of a control unit and a RF head connected by triax cable or Fiber-Optic (optional). The control unit has a 70 MHz output connection available through which it is possible to transmit the signal to the RF head in DVB-T2, DVB-T and optionally in DVB-S2 or DVB-S modulations.
  • Page 12 The equipment is fed with AC power supply from 90 to 240 V. Its excellent design, mechanical and electronic assembly make the UDT-70 a robust and reliable solution. DVB-T2 features Its maximum output power is 3 Watt in 2 GHz and 1 Watt in the rest of the bands.
  • Page 13 46.4 Mbps. DVB-T features The RF stage of the UDT-70 transmitter is the same as the DVB-T2 one. The difference is found in the modulation part as it is commented bellow. The UDT-70 digital camera transmitter uses COFDM (Coded Orthogonal Frequency Division Multiplexing) modulation system (2K mode).
  • Page 14 31.67 Mbps. DVB-S2 features (optional) In case the UDT-70 transmitter is needed to be used as a satellite transmitter, it features an optional IF stage in the L band , that L band output that provides a 10 MHz reference oscillator.

  • Page 15: Chapter 2:Technical Features

    Bandwidth: 5, 6, 7, 8 MHz Max. bitrate: 31.67 Mbps DVB-S2 (Optional): QPSK, 8PSK, 16APSK, 32APSK LDPC FEC: 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10 Max. Symbol Rate: 25 Msymb/s UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 16 Frequency Tolerance: ± 1,0 ppm Frequency Stability: ± 0,30 ppm Operating Temperature Range:-40 to +85ºC Phase Noise: 10 Hz_____-100 dBc/Hz 100 Hz____-130 dBc/Hz 1 kHz_____-147 dBc/Hz 10 kHz____-156 dBc/Hz 100 kHz___-160 dBc/Hz 1 MHz_____-160 dBc/Hz UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 17 1,200 to 57,600 bps ASI and IP Input and Output: ASI Transport Stream (EN50083-9) ASI over IP (SMPTE2022/CoP3) – FEC (optional) Encryption BISS: BISS-1 and BISS-E AES (Optional): AES-128 and AES-256 Remux: (Optional) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 18 Size: 185.5 x 84 x 339 mm Weight: 4.6 kg Max. distance Between: 2Km with Fiber-Optic (Optional) Control unit and RF Head 400 m (triax cable 11 mm) Control unit- IF Head: SMPTE Fiber-Optic (Optional) Connector TRIAX UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 19: Chapter 3: How To Order

    Chapter 3: How to Order UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 20: Chapter 4:Transmitter Operation And Menus

    This third chapter provides the user all the necessary information to control, configure and operate the equipment properly. 4.1 Display To switch the equipment on and off, press ON/OFF button. When the equipment is turned on, the main screen of the UDT-70 transmitter is shown. Reflected Power Frequency Transmission Standard...
  • Page 21 Standard Delay (Lipsync < 10 ms) Low delay (Lipsync < 10 ms)  3 frame Super Low Delay (Lipsync < 10 ms)  2 frame Ultra Low Delay (Lipsync = 20 ms)  1 frame UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 22: Menus

    In the next page it is shown a scheme that specifies the different menu options available. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 23 None Nº Videos Nº Videos Status Embedded Embedded Embedded Embedded Embedded Embedded Embedded Embedded Format Bitrate Format Analogue Analogue Latency Latency Profile Profile Generator Generator Depth Depth Mode Mode Sample Sample Format Format UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 24 Audio1 PID TP per IP Audio2 PID Audio3 PID Protocol Audio4 PID Antenna 5V Baud Rate Audio5 PID Stream Audio6 PID GPS Info Diagnosis Audio7 PID Audio8 PID Data PID PMT PID PCR PID UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 25 Modulation Modulation Modulation Modulation LDPC FEC LDPC FEC LDPC FEC LDPC FEC Ratio and Bandwidth Ratio and Bandwidth Guard Interval Guard Interval ODU Unit ODU Unit Spectrum Time interleaving ODU Unit ODU Unit UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 26 Distance Units Mask Encoder OSD Timer Voltage T / T2 Carrier Gate Voltage OSD Position Activation Key Admin Pas Restore Encoder S/N Admin Pas Activation Licenses User Pas Load Encryption keys Restore User UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 27: Menu Navigation

    4.2.1 Menu Navigation This section contains a detailed description of each parameter that can be configured in the UDT-70 transmitter via the MENU. To enter the MENU, press the cross button in case of being in the principal screen or in any submenu.

  • Page 28: Menu Structure

    RF – DVB-T2/T/S2/S transmission parameters are set in this section. Unit –Parameters related to the Web Server and other internal options of the UDT-70 transmitter are configured here, as well as other characteristics of the device. UDT-70 Two Box Portable Transmitter...

  • Page 29: Encoder Menu

    Audio 6: Generator < Audio 7: Generator < Audio 8: None > ENCODER Data: RS232 <> KLV Metadata: Off > Encoder Output ENCODER TS Parameters Scrambler: None > Remux: Disable > Figure 3 Encoder Menu UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 30 Once the Audio 1 input has been selected, press the OK button to configure the parameters related to it. The available options are: None • Embedded • • Generator UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 31 Once the Audio 2 input has been selected, press the OK button to configure the parameters related to it. The available options are: None • Embedded • • Generator UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 32 None • BISS-1 • BISS-E • AES-128 (Optional) • AES-256 (Optional) • Remux (eligible parameter) (Optional): In this field, remux option can be activated. This feature is optional. Table 1: Encoder Menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 33 4xHD. Flexible video input format and 4x HD operation. • Format: In this field, the video format is selected. The available options are: Auto UHD. • Auto HD. • Manual. Used for other brand encoders. • UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 34 In this field, the sample format is selected. The available options are: • 2SI. 4K video inputs in 2 Sample Interleave format. • SQD. 4K video inputs in Square Division format. Table 2: SDI Input options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 35 (reading parameter) The available options are: Present  No Present  Bitrate: In this field, the bitrate of the ASI input signal is shown. (reading parameter) Table 3: ASI Input menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 36 4xHD. Flexible video input format and 4x HD operation. Format: In this field, the video format is selected. The available options are: • Auto UHD. Auto HD. • Manual. Used for other brand encoders. • UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 37 In this field, the sample format is selected. The available options are: • 2SI. 4K video inputs in 2 Sample Interleave format. • SQD. 4K video inputs in Square Division format. Table 4:Generator Input menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 38 Audio Stream Bitrate (Kb/s): In this field, the audio stream bitrate, currently information only which depends on the encoding mode. Table 5: Audio Embedded Input menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 39 In this field, the type of analogue audio input can be selected. The available options are: Line. • Micro Dynamic. • Micro Phantom. • • Variable. Table 6: Audio Embedded Input menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 40 • latency mode will increase video latency. Audio Stream Bitrate (Kb/s): In this field, the audio stream bitrate, currently information only which depends on the encoding mode. Table 7:Audio Embedded Input menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 41 Left keys. To save the value, press the OK button. (editable parameters) Video over IP MAC: • In this field the MAC address of the Video over IP card is displayed (reading parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 42 To save the value, press OK button. (editable parameter) Stream Diagnostics: In this field the estimated bitrate and IP packet size is shown. Table 8: IP Output menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 43 Figure 11: RS232 screen Data option Parameters Baudrate (eligible parameter): Select the baudrate at which data user is received (Baudrate options are: 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, 115200, 230400). Table 9: RS232 Parameters UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 44 GPS receiver using an external GPS antenna (which must be connected to the GPS Antenna Input). This information is sent to receiver. The antenna is fed directly from the transmitter at 5 V. Figure 12: Internal GPS Main screen UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 45 • Height of the Transmitter: The height of the transmitter from ground is specified in this value. • Satellite Level: The level of each satellite signal received is shown in this field. • Date: The updated date is shown. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 46 TS Parameters Figure 14: KLV Metadata option Once that KLV is received at ground, using the TS over IP output of the receiver, KLV metadata can be monitored by a Mission Monitor program. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 47 If the user selects the manual option, the first and second lines disappear on the main screen. When the encoder output is in Manual, if you activate the RF, the encoder output changes to AUTO mode automatically. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 48 Here the Program number must be entered. To change its value, first press the OK button and then, with the UP, Down arrows select the desired number. Press the OK button to save the introduced value. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 49 Here the Data packet identifier must be entered. To change its value, first press the OK button and then, with the UP, Down arrows select the desired number. Press the OK button to save the introduced value. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 50 To change its value, first press the OK button and then, with the UP, Down arrows select the desired number. Press the OK button to save the introduced value. Table 12:Encoder TS menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 51 Press the OK button to introduce the key. With Left and Right buttons select one field and with UP, Down buttons choose one value from 0 to 9 or A to F. Press the OK button to set the key. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 52 Figure 19: Remux work diagram ASI bitrate must be known. You must configure it to have ASI input Bit rate plus NTT encoder Bit rate minor than modulator total Bit rate. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 53 Power: High (30 dBm) < DVB-T2 Bandwidth: 8 MHz < Modul: 256QAM < LDPC Fec: 3/5 <> DVB-T2 GI: 1/16 <> FFT: 2K > Time Int: 100(100) DVB-T2 ODU Unit Figure 21: DVB-T2 UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 54 The available options are: When ODU unit selected: • Low (24dBm) • High (30 dBm) When PA-10 selected • • • High When RF OUTPUT Selected • Editable from -5dBm to +20 dBm UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 55 Here the value of the Forward Error Correction can be chosen. Use the Right, Left buttons to select the desired value. The available options are: • 1/2 • 3/5 • 2/3 • 3/4 • 4/5 • 5/6 UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 56 Up and Down buttons. ODU Unit In this field, users can control ODU units: Alarms  Temperature  Voltage  SN/RV  Edit ODU channels  Table Table 14: DVB-T2 menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 57 QPSK 10.5 11.3 11.7 14.5 17.5 19.4 16 QAM 21.8 23.3 24.3 21.5 25.9 28.8 64 QAM 32.4 34.6 36.0 29.0 34.9 38.8 256 QAM 43.7 46.6 48.6 Table 15: DVB-T2 Maximum Bitrates UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 58 F: 1.040,50 (CH 1) Power: High (30dBm) > DVB-T Bandwidth: 8 MHz < Modul: 64 QAM < FEC: 1/2 > DVB-T GI: 1/4 < Spectrum: Normal > ODU Unit Figure 22: DVB-T Menu UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 59 The available options are: When ODU unit selected: • Low (24dBm) • High (30 dBm) When PA-10 selected • • • High When RF OUTPUT Selected • Editable from -5dBm to +20 dBm UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 60   Here the Guard Interval value can be chosen. Use Right, Left buttons so as to select the desired value. (eligible parameter) The available options are:   1/16  1/32  UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 61 The available options are: Normal  Invert  ODU Unit In this field, users can control ODU units: Alarms  Temperature  Voltage  SN/RV  Edit ODU channels  Table 16: DVB-T menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 62 In the following tables, the values in italics are approximate values for the given channel bandwidth. Table 17:Useful bitrate (Mbit/s) for non-hierarchical systems in 8 MHz channels Table 18: Useful bitrate (Mbit/s) for non-hierarchical systems in 7 MHz channels UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 63 Table 19: Useful bitrate (Mbit/s) for non-hierarchical systems in 6 MHz channels Table 20: Useful bitrate (Mbit/s) for non-hierarchical systems in 5 MHz channels UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 64 DVB-S2 (Optional) DVB-S2 Sel: 1-3GHz > F: 2.300,00 (CH 1) Power: High (30 dBm) < DVB-S2 Modul: QPSK > LDPC Fec: 3/4 <> SR: 12.400 B:14.88 DVB-S2 ODU Unit Figure 23: DVB-S2 Menu UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 65 So as specify the output power, select it in the power option) Modulator (The RF output carrier with modulation. So as  specify the output power, select it in the field below) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 66 In this field, the value of the symbol rate can be introduced. (editable parameter) In this field, the value of the bandwidth of the transmitted signal is displayed. (reading parameter) This parameter is automatically adjusted according to the selected transport stream parameters. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 67 The available options are: None  12,80 GHz  13,05 GHz  Table 21:DVB-S Menu Additionally, when L-Band is selected, the following parameters can be configured: UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 68  Antenna Gain: Select the gain of the transmitter antenna. Press the OK button to configure it and then the OK button again to save the introduced value.(editable parameter) Table 22:DVB-S2 menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 69 Next, it is shown a table as an example of the Symbol Rate values for a determined Bandwidth of 28 MHz. Symbol Rate Bandwidth (MHz) Roll-off (Msymb/s) 0.20 23.33 0.25 22.4 0.35 20.74 Table 23: Symbol Rate calculation UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 70 4.2.3.1.4 DVB-S (Optional) DVB-S DVB-S Sel: 1-3 GHz > FEC: 7/8 < F: 2.300,00 (CH 1) SR:12.400 B:16..74 Power: High (30 dBm) < ODU Select Figure 24: DVB-S Menu UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 71 So as specify the output power, select it in the power option) Modulator (The RF output carrier with modulation. So as  specify the output power, select it in the field below) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 72 Buc is used in the transmission (uplink) of satellite signals. It converts a band of frequencies from a lower frequency to a higher frequency. The available options are: None  12,80 GHz  13,05 GHz  UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 73 Antenna Gain (dBi): Select the gain of the transmitter antenna. Press the OK button to configure it and then the OK button again to save the introduced value.(editable parameter) Table 24: DVB-S menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 74 • No ASI Input: ASI source is not connected. • No GPS: GPS source is not connected. • No KLV • PA No Forward • PA Rev High • PA Volt Low • PA Temp High UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 75 (values from 0 to 3) where 0 means that the fans are stopped and value 3 is the maximum speed. (Reading parameter) Voltage:  In this field, the voltage of the transmitter is shown. (Reading parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 76 4.2.3.2.3 Remote UNIT ETHERNET LOC 192.168.001.010 MSK 255.255.000.000 GAT 192.168.001.001 UNIT ETHERNET MAC: 70-B3-D5-1A-C0-00 Admin Pass: ******** Restore Admin Pas UNIT ETHERNET User Pass: ******** Restores User Pas Figure 27: Remote UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 77 To set the password, press the OK button and then use the Up and Down buttons to establish the desired value, then press the Right and Left buttons to change other digits. Finally press OK button to save the introduced values. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 78 Left buttons to change other digits. Finally press the OK button to save the introduced values. Restore User Pass: This option enables to restore the default user password (00000000). Table 25: Unit Ethernet menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 79 T/T2 Carrier: Off UNIT MISCELLANEOUS Activ Key:******* > S/N: 660010911 Enc S/N: XXXXXXXX UNIT MISCELLANEOUS Activ Licenses: Load Encry Keys: OSD Timer: Off > UNIT MISCELLANEOUS OSD Position:Bot > Figure 28: Miscellaneous Menu UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 80 It must have 8 characters alphanumeric. S/N: In this field the serial number of the device is shown (reading parameter). Encoder S/N: In this field the serial number of the encoder is shown (reading parameter). UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 81 For a new license code, please contact us. Load Encry Keys: n this field you can load the encryption keys for BISS and AES modes by USB. The file must have “.svp” extension and the content must be as it is indicated in the following example: AES128:1202A3412348C9127348FE2348971234...
  • Page 82 The rest of the characters are important for the manufacturer but are not important for the user. Table 27: Unit Firmware menu options UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 83 Next, the necessary steps so as to make a successful update are explained. The latest firmware is allocated in the webpage of SVP Broadcast Microwave. So as to access to the firmware file, first enter www.svpbm.com in your web browser.
  • Page 84 Click on Firmware. Figure 31: Updating firmware step 3 UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 85 (with no power With equipment completely power off supply), insert the USB device in the USB connector, situated in the rear panel. Before introducing the USB device, remove the power supply of the equipment. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 86 Don’t power off the device during the updating process. You must remove the USB before start working with the new firmware. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 87: Chapter 5: Web Server

    Chapter 5: Web Server 5.1.1 ENCODER Figure 33: Web Server Encoder screen UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 88 Embedded, Analogue, AES-EBU, Test Tone Generator and None. (eligible parameter) [A1] Bitrate:  Select the bitrate for the coding process of the audio 1 signal. The available options are 128, 192, 256 and 384 Kbps. (eligible parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 89 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600. (eligible parameter) Parity:  Select the parity for the RS-232 connection. The available options are None, ODD and Even. (eligible parameter) Stop Bits:  UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 90  The height of the transmitter from ground in meters is specified in this value. (reading parameter) Direction:  The direction in degrees of the transmitter is shown in this field. (reading parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 91 Here the program map tables packet identifier must be entered. (editable parameter) PCR PID:  Here the program clock reference packet identifier must be entered. (editable parameter) Program Number:  Here the program number must be entered. (editable parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 92 FEC, IG, BW used, so as to the video bitrate can be always the maximum allowed. SVP advises to use the automatic mode when the signal is transmitted through RF. Manual mode is useful when the device is used as an encoder so as to configure the desired output bitrate in the ASI output.
  • Page 93 Uses an encrypted key AES-128  AES-256  5.1.1.5.2 Remux Mode: • Here you can enable or disable Remux mode, when de enable mode is selected, Transport Stream Bitrate mode is always manual. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 94 DVB-T2, DVB-T, DVB-S2 and DVB-S. (eligible parameter) RF Status:  Select ON in case of wanting to activate the RF transmission or press OFF button so as to deactivate it. (eligible parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 95 Select the FEC value for the transmitted signal. The available options are 1/2, 2/3, 3/4, 5/6, 7/8. (eligible parameter)  Select the guard interval of the transmitted signal. The available options are 1/4, 1/8, 1/16, 1/32. (eligible parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 96 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 97 The available options are: 1-3 GHz  3-14 GHz  PA 2.0-2.4 GHz (Optional output)  RF OUTPUT  Frequency:  Introduce the frequency at which the signal is being transmitted. (editable parameter) Power:  UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 98 Only the time interleaver mode 0 (TIME_IL_TYPE=0) is supported, so one interleaving frame always equates to exactly one OFDM frame. To desactivate the time interleaver, this parameter must be set to 0. (editable parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 99 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 100  LBAND (Optional output)  Frequency:  Introduce the frequency at which the signal is being transmitted. (editable parameter) Output Mode:  Specify the transmission mode which can be no output. (eligible parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 101 In this field, the value of the bitrate of the transmitted signal is displayed. (reading parameter) 10 MHz:  10 MHz reference oscillator mode ON or OFF. This feature provides a reference signal to the satellite up-converter in case of being ON. (eligible parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 102 In this option, the user can choose the type of the ODU unit. (elegible parameter) The available options are: 1-3 GHz  3-14 GHz  LBAND (Optional output)  Frequency:  Introduce the frequency at which the signal is being transmitted. (editable parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 103 (reading parameter) Spectrum:  Here the type of the spectrum is configured. Inverted spectrum is just another method to help preventing signal theft. The spectrum options are inverted and normal. (eligible parameter) UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 104 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 105 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 106: Unit

    5.1.3 UNIT Figure 40: Web Server UNIT screen UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 107 (constellation, FEC, GI...). The different warnings that can appear in the transmitter are: No Video Input. No GPS. UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 108 In this field, the administrator’s password is introduced. It can be set an own password which is a list of 8 digits. Then, to save the introduced value, press Enter button. Moreover, there is the option to restore the default administrator password (00000000). UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 109  In this field the serial number of the ODU is shown (reading parameter). Revision  In this field it is shown the number of the version installed in the ODU (reading parameter). UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 110 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 111: Web Page Setup Notes

    1. Open a new tab, in the address bar enter about:config 2. In the Filter box, enter disk 3. Set the value for 'browser.cache.disk.enable' to false (double click to change the setting). 4. Close the about:config tab. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 112: Chapter 6: Equipment Installation

    6.2 Connections Every connection of the UDT-70 camera transmitter is on the rear panel, except for the RF antenna connections that are on the front panel. All the Lemo part numbers and pinout refer to the connector that is fixed to the cable.
  • Page 113 The following figures show the UDT-70 front and rear panel. The connections mentioned in the upper figure are shown below. Figure 42: UDT-70 front panel Figure 43: UDT-70 rear panel UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 114: Power Supply

    Power supply AC connection technical features Item Features Connector label POWER A.C. Connector type MLC Neutrik Supply voltage 90-240 V. (50/60Hz) Table 28: AC Power supply features Pinout UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 115 Power supply DC connection technical features Item Features Connector Label POWER D.C. Connector Type XLR-4 male Supply voltage 11-36 V. Table 30: DC Power supply features UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 116 Pinout Figure 44: Connector pinout Description + VCC + VCC Table 31: DC Power supply connector pinout Connector needed Figure 45: Connector needed The DC input is protected by a fuse (ATO model) UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 117: Intermediate Frequency

    There is a 70 MHz test signal output available. 70 MHz TEST connection technical features Item Features Connector label 70 MHz TEST Connector type SMA female Impedance 50 Ω Table 33:70 MHz Test connections characteristics UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 118: L-Band Dvb-S2 (Optional)

    6.2.4 L-Band DVB-S2 (Optional) The satellite up – converter is directly connected to the female SMA – type connector on the rear panel of the UDT-70. L Band connection technical features Item Features Connector label L Band DVB-S2 Connector type...

  • Page 119: Asi

    ASI output signal type uses 75Ω Mini BNC connector. This connector is placed on transmitter rear panel. It is important that 75 Ω connectors are used. This is because the female output connector of the UDT-70 unit may be damaged because of an impedance mismatch. ASI OUT connection technical features...

  • Page 120: Sdi 1 To 4

    800 mVpp nominal ±10% Table 39: SDI input signal connection features 6.2.9 Transport Stream over IP OUTPUT (Optional) The UDT-70 transmitter has a connector that allows using the ODI as standalone IP encoder. TS over IP connection technical features Item...

  • Page 121: Data Input

    6 pin Lemo 0B connector on equipment’s rear panel. Data connection technical features Item Features Connector Label DATA Connector type 6 pin Lemo 0B Cable connector part number FGG.0B.306.CLAZ Manufacturer Lemo Table 43: Data input connection technical features UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 122: Usb Connection

    Table 44: Data cable connector pinout 6.2.12 USB connection Thanks to the USB connection, it is possible to update directly from an external USB device the firmware of the UDT-70 transmitter. The connector is type A. USB connection technical features Item...

  • Page 123: Remote

    This connection allows the user to monitor and setup any parameter of the transmitter throughout Web Browser through the network. Remote connection technical features Item Features Connector Label Remote Connector type RJ-45 Table 46: Remote input connection technical features UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 124: Rack Unit Installation

    The up-converter is installed next to the transmitter antenna. The form that the antenna is connected to the up-converter input is through mechanical hook. The up-converter is connected to the UDT-70 transmitter through a triax cable. For better performance high quality cables and connectors should be used.

  • Page 125: Antenna Installation

    6.5 Antenna Installation Parabolic antenna is connected to the up-converter through a mechanical hook as shown Figure 47: UDT-70 transmitter system installation UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 126: Chapter 7: Up Converter

    FRQ between the 15 pre-set frequencies. If you want to edit pre-set frequencies, you must do it from settings menu in the ODU menu. To configure the reception frequency remotely, the frequency selector has to be set in slave mode. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 127: Display

    LDPC FEC (1/2, 3/5, 2/3, 3/4, 4/5, 5/6)  Guard Interval (1/4, 19/128, 1/8,19/256, 1/16, 1/32, 1/128)  Bandwidth  Transmitted bitrate  Input type  Alarms  Output power level set in the transmitter  UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 128: Settings

    Volume: to set the volume of the unit o TFT mode: to change between day and night mode. o Bright: to set different brightness levels o Advanced: To access advanced menu (only accessible by SVP technical department) 7.2.3 Info 7.2.3.1 Device...

  • Page 129: Keyboard Lock

    LED next to alarm button lights. 7.2.4 Keyboard Lock If you press this key for a few seconds, the touch screen will be locked. To unlock it, press it again. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 130: Mechanical Dimensions

    7.3 Mechanical Dimensions Figure 52: Mechanical Dimensions UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 131: Connections

    Connector label SMPTE FIBER Connector type (equipment) LEMO serie 3K.93C Part Number (equipment) EDW.3K.93C.TLE Part Number (cable) FUW 3K.93C Manufacturer Lemo Required cable 2SM-9.2-37.5 Table 48: SMPTE Fiber Intermediate frequency connector technical features UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 132: Index A - T-Box

    Index A – T-Box The T-Box is a device which splits the signal to the two up-converters. Next, it is shown the mechanical drawing of the device. A.1 Mechanical Drawing Figure 53: T-Box mechanical drawing UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 133: Index B: Scda User's Guide

    3. The high performance of this equipment is only guaranteed when using high quality cables and connectors. 4. Only authorized personnel should open the product and any repair or warranty will be invalidated if the seals are broken. Figure 54: SCDA Duplexor UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 134: Description

    The equipments can be up-converters or down-converters. This configuration makes possible for both equipments to share the same tripod and the same antenna. The bracket has two clasps, one for each equipment, to prevent an unwanted manipulation. UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 135: Technical Specifications

    Stainless Steel Weight 2 kg (4.4 Ib) Size Width: 300 mm (11.8 inches) Height: 150 mm (5.9 inches) (without connectors) Depth: 22 mm (0.86 inches) Table 49: SCDA Main Characteristics Figure 55: SCDA Duplexor UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 136: Configurations

    B.3 Configurations Figure 56: 1+1Configuration Figure 57: Bidirectional Configuration UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 137 Figure 58: Single Link Configuration UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 138 3. The high performance of this equipment is only guaranteed when using high quality cables and connectors. 4. Only authorized personnel should open the product and any repair or warranty will be invalidated if the seals are broken. Figure 59: HAP-60 Parabolic Antenna UDT-70 Two Box Portable Transmitter MANUAL V1.0...

  • Page 139: Description

    60 cm diameter. This antenna works in the 2 GHz, 6GHz, 7 GHz and 10 GHz frequency bands. It has been especially designed to be used in portable SVP links. So it can be clamped to the RF head of SVP equipment.

  • Page 140: Technical Specifications

    2 GHz, 6GHz, 7 GHz and 10 GHz Bandwidth 500 MHz Gain Depends on the frequency Polarization Linear VSWR Typ: < 1.8 Connector N female Diameter 60 cm Weight 5 kg Table 50: HAP-60 Main Characteristics UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 141 Conditional Access-BISS COFDM Coded Orthogonal Frequency Division Multiplexing Direct current DVB-S2 Digital Video Broadcasting by Satellite – Second Generation DVB-T Digital Video Broadcasting – Terrestrial DVB-T2 Digital Video Broadcasting – Terrestrial Second Generation ETSI UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 142 HDMI High-Definition Multimedia Interface High Definition Receiver High Definition Transmitter Intermediate Frequency Interval Guard Internet Protocol Liquid Crystal Display Light-Emitting Diode Low Delay MPEG Moving Picture Experts Group NLOS Non Line of Sight UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 143 Phase Alternating Line Packet Identification Quadrature Amplitude Modulation QPSK Quadrature Phase-Shift Keying RadioFrequency Remote Control Standard Delay Serial Digital Interface Thin-Film Transistor Transport Stream User Datagram Protocol Universal Serial Bus UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 144 Note UDT-70 Two Box Portable Transmitter MANUAL V1.0...
  • Page 145 Final note SVP Broadcast Microwave S.L. is constantly striving to improve all of its products. Therefore, we ask you to understand that modifications may occur in designs, equipment and technology. Consequently, no responsibility can be derived from the information, illustrations or descriptions contained in this manual.
  • Page 146 SVP Broadcast Microwave reserves the right to make changes to this manual and to the equipment without prior notice. C/ Zubiaurre 7 bajo 48215 Iurreta Vizcaya – Spain Tel: (+34) 94620 3722 info@svpbm.com www.svpbm.com...

Table of Contents