Related Manuals for C-Dax C-DIT400
Summary of Contents for C-Dax C-DIT400
- Page 1 OWNER’S MANUAL FOR THE GROUND DRIVEN SPREADER C-DIT400 C-Dax Ltd PO Box 1010, 145 Harts Road Tiritea, Palmerston North Ph:06 354 6060 Fax:06 355 3199 E-Mail: sales@c-dax.co.nz www.c-dax.co.nz...
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS CDIT400 AN IMPORTANT MESSAGE FOR OWNERS & OPERATORS OF C-Dax ATTACHMENTS/ACCESSORIES Be warned of the dangers of loading your ATV or other vehicle in excess of its carrying capacity. It is important to understand that any loads or attachments whether fastened to or placed on a vehicle or ATV will alter the stability or handling characteristics of that vehicle or ATV. - Page 3 SAFETY PRECAUTIONS Before attempting to install or operate the equipment, read and understand the manual thoroughly. Failure to comply with this instruction constitutes improper use and will invalidate the warranty. Throughout this manual there are highlighted text boxes containing warnings, cautions and notes. Warnings are mandatory instructions to prevent serious injury or permanent damage.
-
Page 4: Table Of Contents
C-Dax CDIT400 OWNER’S MANUAL (Pt.No.2400-5610 Issue 8 Dated 02 Dec 2010) TABLE OF CONTENTS Safety Precautions Table of Contents Introduction Description Specifications Order Information Warranty Liability Operation Calibration Magnesium Oxide Operating the Spreader Adjusting the Spread Pattern Fitting the Cover... -
Page 5: Introduction
All goods returned to C-Dax Ltd are freight paid by the sender and if subject to a warranty claim, must be accompanied by a completed warranty claim form. Warranty claim forms are available from C-Dax dealers. -
Page 6: Liability
LIABILITY The maximum liability, which is accepted by C-Dax Ltd, is limited to replacement of faulty goods only. Every care has been taken in the manufacture of our goods but because use of the goods is outside the control of the manufacturer, the end user assumes all responsibility for the use. -
Page 7: Operation
OPERATION The product to be spread is placed in the hopper. When the spreader is towed forward, the right hand wheel drives through the lever operated mechanical clutch and gearbox to turn the spinner in a clockwise direction. When the control handle is in the disengage position (fully back) the clutch is disengaged and the shutter is closed. -
Page 8: Calibration
CALIBRATION 1. Ensure the control handle is fully back (clutch disengaged, shutter closed). 2. To calibrate your spreader, place a measured amount of product (10 Kg) in the hopper. 1. Set the Shutter Stop Lever to the position (1-9) indicated in the Calibration Guides below. Hole position 9 (shutter fully open) is denoted by two holes vertically one above the other. -
Page 9: Operating The Spreader
OPERATING THE SPREADER When the spreader has been correctly calibrated, the hopper may be filled to the required level and spreading commenced. To reduce agitator damage to product and to ensure that product is not forced past the agitator shaft when towing the spreader to the area to be treated, the drive to the gearbox should be disconnected by ensuring the control lever is in the disengage position (fully back). -
Page 10: Maintenance
MAINTENANCE The following maintenance actions are mandatory for reliable use of the spreader. Before Use Check the tyre pressures and charge with air as required. The correct pressure is 15PSI (100Kpa). Disengage the clutch by ensuring the control lever is fully back then turn the spinner by hand to ensure that it is free to turn without interference. -
Page 11: Parts Diagram
PARTS DIAGRAM... -
Page 12: Parts List
PARTS LIST Item Part QTY. Description Drawbar-ASY-CDIT400 2550-1400 3500-5700 CDIT400 Frame-GL Hopper-CDIT400GT-MDPE 7500-2160 7500-2500 Lid-Full-CDIT400GT-MDPE WheelASY-18x950x8-Keyed-Knobbly 9200-4600 9200-4500 WheelASY-18x950x8-Bearing-Knobbly MUDGAURD-BLUE-MDPE-1/2 7500-2590 RIVET-3/16"x15-TRUSS HD-AL 3240-0015 Gearbox-Ferroni-RV10 3800-1000 Bolt-M10x120-ZP 2840-1120 NUT-M10-ZP 3180-0010 Shaft-Axle-CDIT400-ZP 5200-6600 3290-1225 Screw-HH-M12x25-ZP Washer-Flat-M12x32x3-GL 3310-5012 Nut-Nyloc-3/4UNF-ZP 3150-5100 Washer-Flat-Stub Axle-M20x29x3-ZP 3310-5021 Bolt-M12x90-ZP 2840-1290... - Page 13 Bolt-M8x80-SS 2810-0880 3290-1275 Screw-HH-M12x75-ZP BKT-Clutch-CDIT400GT-ZP 1300-3010 WASHER-FLAT-M10-ZP 3310-6010 Clamp-Hose-Oetiker3740-ZP 2000-3037 2890-0816 Screw-Cap-M8x16-Grade12.9 NIPPLE-GREASE-M6x1x5-CP 5270-0003 Screw-Cap-M8x12-Grade12.9 2890-0812 Washer-34.9IDx67ODx2SS304 6500-9000 Shutter-CDIT300GD-DLD 6500-7770 Shroud-CDIT400GT-MDPE 7500-2690 Rivet-5x5/8-SS 3240-5100 3310-9200 Washer-Flat-3/16x1/2-SS Spout-CDIT400GT-MDPE 7500-2830 SCREW-HH-M8x16-ZP 2840-0816 Link-Hopper-CDIT400-LH-ZP 5245-8000 Link-Hopper-CDIT400-RH-ZP 5245-8001 Handle-Mount-CDIT400-ZP 5245-3900 Spring-COMP-Crinkle Plate 8250-1800 BOLT-M10x65-ZP 2840-1065 Arm-Indicator-400GT 4050-4250...